Radiation Induced Structural Changes in Normal Spinels

2007 ◽  
Vol 1043 ◽  
Author(s):  
David Simeone ◽  
Gianguido Baldinozzi ◽  
Dominique Gosset ◽  
Leo Mazerolles ◽  
Lionel Thome
Keyword(s):  
Radiation Effects ◽  
Structural Changes ◽  
Ion Irradiation ◽  
Atomic Scale ◽  
X Ray Diffraction ◽  
Unified Framework ◽  
X Ray ◽  
Transmission Electron ◽  
Radiation Induced ◽  
Diffraction Patterns

AbstractIon irradiation induced phase transformations in three normal spinel compounds MgAl2O4, MgCr2O4 and ZnAl2O4 have been investigated by X-ray diffraction, Raman spectroscopy and Transmission Electron Microscopy. This work presents a unified framework to describe the radiation effects in normal spinels. Irradiation modifies the atomic and mesoscopic structures of theses spinels in different ways. At the atomic scale, it produces the inversion of the cations in the spinel structure which can always be described within its usual Fd-3m space group. At the mesoscopic scale, it produces microdomains, responsible for the important changes in the X-ray diffraction patterns.

scholarly journals Microstructure and properties of nano-laminated Y3Si2C2 ceramics fabricated via in situ reaction by spark plasma sintering

2021 ◽  
Vol 10 (3) ◽  
pp. 578-586
Author(s):  
Lin-Kun Shi ◽  
Xiaobing Zhou ◽  
Jian-Qing Dai ◽  
Ke Chen ◽  
Zhengren Huang ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Atomic Scale ◽  
Max Phase ◽  
X Ray Diffraction ◽  
Selected Area Electron Diffraction ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma ◽  
Diffraction Patterns

AbstractA nano-laminated Y3Si2C2 ceramic material was successfully synthesized via an in situ reaction between YH2 and SiC using spark plasma sintering technology. A MAX phase-like ternary layered structure of Y3Si2C2 was observed at the atomic-scale by high resolution transmission electron microscopy. The lattice parameters calculated from both X-ray diffraction and selected area electron diffraction patterns are in good agreement with the reported theoretical results. The nano-laminated fracture of kink boundaries, delamination, and slipping were observed at the tip of the Vickers indents. The elastic modulus and Vickers hardness of Y3Si2C2 ceramics (with 5.5 wt% Y2O3) sintered at 1500 °C were 156 and 6.4 GPa, respectively. The corresponding values of thermal and electrical conductivity were 13.7 W·m-1·K-1 and 6.3×105 S·m-1, respectively.

Cetyltrimethylammonium bromide- and ethylene glycol-assisted preparation of mono-dispersed indium oxide nanoparticles using hydrothermal method

2014 ◽  
Vol 68 (8) ◽  
Author(s):  
Selvakumar Dhanasingh ◽  
Dharmaraj Nallasamy ◽  
Saravanan Padmanapan ◽  
Vinod Padaki
Keyword(s):  
Ethylene Glycol ◽  
Hydrothermal Method ◽  
Indium Oxide ◽  
Cetyltrimethylammonium Bromide ◽  
Oxide Nanoparticles ◽  
X Ray Diffraction ◽  
Hydrothermal Conditions ◽  
X Ray ◽  
Transmission Electron ◽  
Diffraction Patterns

AbstractThe influence of cetyltrimethylammonium bromide and ethylene glycol on the size and dispersion of indium oxide nanoparticles prepared under hydrothermal conditions was investigated. The precursor compound, indium hydroxide, obtained by the hydrothermal method in the absence as well as the presence of cetyltrimethylammonium bromide, was converted to indium oxide by sintering at 400°C. The formation of nanoscale indium oxide upon sintering was ascertained by the characteristic infrared adsorption bands and X-ray diffraction patterns of indium oxide. Transmission electron microscopy and band gap values confirmed that the cetyltrimethylammonium bromide facilitated the formation of indium oxide nanoparticles smaller in size and narrower in distribution than those prepared without the assistance of cetyltrimethylammonium bromide.

Structural changes in titanium dioxide nanocrystals during plastic deformation

2005 ◽  
Vol 38 (5) ◽  
pp. 749-756 ◽  
Author(s):  
Ulrich Gesenhues
Keyword(s):  
Structural Changes ◽  
Crystal Size ◽  
Lower Layer ◽  
High Energy ◽  
Primary Crystal ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Hall Method ◽  
Means Of Transmission

The polygonization of 200 nm rutile crystals during dry ball-milling at 10gwas monitored in detail by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD). The TEM results showed how to modify the Williamson–Hall method for a successful evaluation of crystal size and microstrain from XRD profiles. Macrostrain development was determined from the minute shift of the most intense reflection. In addition, changes in pycnometrical density were monitored. Accordingly, the primary crystal is disintegrated during milling into a mosaic of 12–35 nm pieces where the grain boundaries induce up to 1.2% microstrain in a lower layer of 6 nm thickness. Macrostrain in the interior of the crystals rises to 0.03%. The pycnometrical density, reflecting the packing density of atoms in the grain boundary, decreases steadily by 1.1%. The results bear relevance to our understanding of plastic flow and the mechanism of phase transitions of metal oxides during high-energy milling.

scholarly journals Structural Evolution in Wet Mechanically Alloyed Co-Fe-(Ta,W)-B Alloys

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 800
Author(s):  
Vladimír Girman ◽  
Maksym Lisnichuk ◽  
Daria Yudina ◽  
Miloš Matvija ◽  
Pavol Sovák ◽  
...  
Keyword(s):  
Structural Changes ◽  
Magnetic Measurements ◽  
Structural Evolution ◽  
High Energy ◽  
Control Agent ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
X Ray ◽  
Transmission Electron ◽  
X Ray Absorption

In the present study, the effect of wet mechanical alloying (MA) on the glass-forming ability (GFA) of Co43Fe20X5.5B31.5 (X = Ta, W) alloys was studied. The structural evolution during MA was investigated using high-energy X-ray diffraction, X-ray absorption spectroscopy, high-resolution transmission electron microscopy and magnetic measurements. Pair distribution function and extended X-ray absorption fine structure spectroscopy were used to characterize local atomic structure at various stages of MA. Besides structural changes, the magnetic properties of both compositions were investigated employing a vibrating sample magnetometer and thermomagnetic measurements. It was shown that using hexane as a process control agent during wet MA resulted in the formation of fully amorphous Co-Fe-Ta-B powder material at a shorter milling time (100 h) as compared to dry MA. It has also been shown that substituting Ta with W effectively suppresses GFA. After 100 h of MA of Co-Fe-W-B mixture, a nanocomposite material consisting of amorphous and nanocrystalline bcc-W phase was synthesized.

Facile Refluxing Synthesis of Hydroxyapatite Nanoparticles

2015 ◽  
Vol 68 (8) ◽  
pp. 1293 ◽  
Author(s):  
Pakvipar Chaopanich ◽  
Punnama Siriphannon
Keyword(s):  
Crystallite Size ◽  
Reaction Times ◽  
Single Step ◽  
Hydroxyapatite Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Aqueous Mixture ◽  
Diffraction Patterns ◽  
Microscopy Images

Hydroxyapatite (HAp) nanoparticles were successfully synthesized from an aqueous mixture of Ca(NO3)2·4H2O and (NH4)2HPO4 by a facile single-step refluxing method using polystyrene sulfonate (PSS) as a template. The effects of reaction times, pH, and PSS concentration on the HAp formation were investigated. It was found that the crystalline HAp was obtained under all conditions after refluxing the precursors for 3 and 6 h. The longer refluxing time, the greater the crystallinity and the larger the crystallite size of the HAp nanoparticles. The HAp with poor crystallinity was obtained at pH 8.5; however, the well-crystallized HAp was obtained when reaction pH was increased to 9.5 and 10.5. In addition, the X-ray diffraction patterns revealed that the presence of PSS template caused the reduction of HAp crystallite size along the (002) plane from 52.6 nm of non-template HAp to 43.4 nm and 41.4 nm of HAp with 0.05 and 0.2 wt-% PSS template, respectively. Transmission electron microscopy images of the synthesized HAp revealed the rod-shaped crystals of all samples. The synthesized HAp nanoparticles were modified by l-aspartic acid (Asp) and l-arginine (Arg), having negative and positive charges, respectively. It was found that the zeta potential of HAp was significantly changed from +5.46 to –24.70 mV after modification with Asp, whereas it was +4.72 mV in the Arg-modified HAp. These results suggested that the negatively charged amino acid was preferentially adsorbed onto the synthesized HAp surface.

Size dependent behavior of Fe3O4crystals during electrochemical (de)lithiation: an in situ X-ray diffraction, ex situ X-ray absorption spectroscopy, transmission electron microscopy and theoretical investigation

2017 ◽  
Vol 19 (31) ◽  
pp. 20867-20880 ◽  
Author(s):  
David C. Bock ◽  
Christopher J. Pelliccione ◽  
Wei Zhang ◽  
Janis Timoshenko ◽  
K. W. Knehr ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Structural Changes ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
X Ray ◽  
Size Dependent ◽  
Transmission Electron ◽  
Dependent Behavior ◽  
X Ray Absorption

Crystal and atomic structural changes of Fe3O4upon electrochemical (de)lithiation were determined.

Influence of Aging Time on the Structural Changes of Cassava Thermoplastic Starch

2012 ◽  
Vol 1372 ◽  
Author(s):  
José H. Mina ◽  
Alex Valadez ◽  
Pedro J. Herrera-Franco ◽  
Tanit Toledano
Keyword(s):  
Yield Stress ◽  
Amorphous Phase ◽  
Structural Changes ◽  
Thermoplastic Starch ◽  
X Ray Diffraction ◽  
X Ray ◽  
Second Stage ◽  
Diffraction Patterns ◽  
Type V ◽  
Stress Drops

ABSTRACTIn this work the change in the structural properties of cassava (manihot sculenta Crantz) thermoplastic starch (TPS) under controlled environment (humidity and temperature) was studied. Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD) results showed an evident increasing in the amorphous phase of the TPS regarding the native starch. There was a relative decrease of the band at 1047 cm-1 associated to crystalline structure of starch compared to the amorphous peak at 1022 cm-1. The X-ray diffraction patterns confirmed the increment of the amorphous phase in the TPS samples. Likewise the X-ray diffraction patterns shows evidence of residual type C crystallinity and the formation of a new crystalline phase type VH due to the orientation induced in plasticization process. In first stage of conditioning the tensile yield stress drops from 7.5 drops to 0.5 MPa and the break strain increases 1000%. At the same time it seems that the crystallinity of the samples increases as was evidenced by the gradually increasing of the FTIR band at 1047 cm-1. In a second stage, the yield stress increases, the break strain drops and the crystallinity continue growing steadily. These findings suggest that coexist two phenomena simultaneously in the samples. A phenomenon of re-crystallization (retrogradation) that tends to make the material more stiff and a process of plasticization that tends to softening it. It seems that the latter mechanism predominates in the first stage, at short times, and the former in the second stage, at older times.

A Chemical Solution Route to Rapid Synthesis of Homogeneous Bi100−xSbx Alloys Nanoparticles at Room Temperature

2007 ◽  
Vol 7 (2) ◽  
pp. 525-529 ◽  
Author(s):  
Bo Zhou ◽  
Jun-Jie Zhu
Keyword(s):  
Room Temperature ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Solution Route ◽  
Diffraction Patterns ◽  
Co Reduction ◽  
Chemical Solution Route

A chemical co-reduction route in aqueous solution was developed to synthesize Bi100−xSbx alloys at room temperature. The hydrolyses of Bi(III) and Sb(III) were effectively avoided by selecting proper raw materials and coordinator. X-ray diffraction analysis indicated that the as-prepared Bi100−xSbx alloys were homogeneous and phase-pure, and the Bi/Sb ratios in the alloys were very close to those in the aqueous solutions. The transmission electron microscope observation showed that the as-prepared Bi100−xSbx (x = 0∼100) alloys were particles with a size of tens of nanometers. The selected area electron diffraction patterns confirmed the high crystallinity, the homogeneousness, and the composition controllability of as-prepared alloys. All these characters and the nanometer-scaled size of the alloys are believed to be beneficial to the thermoelectric property of the Bi100−xSbx alloys.

Millable Polyurethane/Organoclay Nanocomposites: Preparation, Characterization, and Properties

2007 ◽  
Vol 7 (2) ◽  
pp. 634-640 ◽  
Author(s):  
M. Siliani ◽  
M. A. López-Manchado ◽  
J. L. Valentín ◽  
M. Arroyo ◽  
A. Marcos ◽  
...  
Keyword(s):  
Barrier Properties ◽  
Substantial Improvement ◽  
Nanometer Scale ◽  
X Ray Diffraction ◽  
Transformation Techniques ◽  
Covalent Bonds ◽  
X Ray ◽  
Transmission Electron ◽  
Organically Modified ◽  
Diffraction Patterns

Novel millable polyurethane (PU)/organoclay nanocomposites have been successfully prepared by conventional transformation techniques. One natural (C6A) and two organically modified (C15A and C30B) montmorillonites have been used as clays for preparing PU nanocomposites. The optimum dispersion of nanofiller at a nanometer scale in PU matrix was confirmed by X-ray diffraction patterns and transmission electron microscopy. A substantial improvement of the PU properties by addition of only a small amount of organoclay was observed. It is worthy to note that the organoclays show a different interfacial interaction with the PU matrix, which was reflected in different macroscopic properties. Thus, C30B organoclay seems to react with PU chains to form covalent bonds, while C15Aonly interacts physically with PU chains. Mechanical and barrier properties are analyzed.

The structural changes of polycrystalline film C60/C70: Ni caused by Ni diffusion

1996 ◽  
Vol 11 (12) ◽  
pp. 3146-3151 ◽  
Author(s):  
E. Czerwosz ◽  
P. Byszewski ◽  
R. Diduszko ◽  
H. Wronka ◽  
P. Dluźewski ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Raman Spectroscopy ◽  
Structural Changes ◽  
Thermal Conditions ◽  
Vacuum Deposition ◽  
X Ray Diffraction ◽  
Polycrystalline Structure ◽  
X Ray ◽  
Transmission Electron

C60/C70: Ni films with 1.5 wt. % Ni concentration obtained by vacuum deposition under different thermal conditions have been investigated. The structural changes of the layers were investigated by transmission electron microscopy, electron and x-ray diffraction, and Raman spectroscopy. The polycrystalline structure was detected for the layers grown at approximately 450 K on the substrate. At elevated temperature and maintained temperature gradient on the substrate during the process, the changes of the layer's structure and the formation of Ni microcrystals were observed. The Ni microcrystals (5–10 nm in the diameter) and the elongated shapes dimensioned 10 × 150 nm were perceived.

Sign in / Sign up

Export Citation Format

Share Document