Growth of (0001) ZnO Thin Films on Sapphire

1996 ◽  
Vol 449 ◽  
Author(s):  
A. J. Drehman ◽  
P. W. Yip
Keyword(s):  
Surface Roughness ◽  
Buffer Layers ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Axis Orientation ◽  
Force Microscopy ◽  
Sapphire Substrates ◽  
Atomic Force

ABSTRACTUsing reactive rf sputtering, we have grown (0001) oriented ZnO films in situ on heated c-axis sapphire substrates, that are promising, particularly in terms of surface roughness, as buffer layers for the subsequent epitaxial growth of III-V nitride films. We compare the effects of on-axis and off-axis sputter geometries on the film epitaxy and smoothness. We also examined the effect of substrate temperature on the growth and smoothness and quality of the film. X-ray diffraction was used to verify the hexagonal ZnO phase, its c-axis orientation and, qualitatively, the degree of its epitaxy. Atomic Force Microscopy (AFM) was used to determine the ZnO growth morphology and roughness. Our best films, obtained by off-axis sputter deposition, have a surface roughness of less than 1 nm.

Ultra-Smooth ZnO Buffer Layers on (001) Sapphire

1997 ◽  
Vol 482 ◽  
Author(s):  
A. J. Drehman ◽  
S.-Q. Wang ◽  
P. W. Yip
Keyword(s):  
Buffer Layers ◽  
Zno Films ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Force Microscopy ◽  
Sapphire Substrates ◽  
Atomic Force ◽  
Electrical Resistivities

AbstractUsing off-axis reactive rf sputtering, we have grown extremely smooth, nearly epitaxial, (001) oriented ZnO films on c-axis sapphire substrates. Atomic Force Microscopy was used to determine that these films are extremely smooth, having an rms roughness of only a few tenths of a nanometer. Based on high resolution x-ray diffraction (HXRD), the ZnO is highly oriented, with a rocking curve width of less than 400 arc seconds for the (006) diffraction peak, and only somewhat larger for the (112) reflection. HXRD Phi scans show that the ZnO (112) reflection is rotated in the a-b plane by 30 degrees from the sapphire (113) direction. These two measurements indicate excellent in-plane orientation. We are investigating the use of these buffer layers for subsequent GaN growth. Electrical resistivities of the films exceeded 100 kΩ-cm making ZnO a potential candidate as an insulating buffer layer.

ZnO Films Deposited on Various Diamond Film Substrates with Different Surface Roughness

2011 ◽  
Vol 287-290 ◽  
pp. 2347-2350
Author(s):  
Rong Fan ◽  
Lin Jun Wang ◽  
Jian Huang ◽  
Ke Tang ◽  
Ji Jun Zhang ◽  
...  
Keyword(s):  
Thin Films ◽  
Surface Roughness ◽  
Diamond Film ◽  
Zno Thin Films ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Free Standing ◽  
Axis Orientation ◽  
X Ray ◽  
Force Microscopy

ZnO thin films were deposited by radio frequency (R. F.) magnetron sputtering on various diamond film substrates with different surface roughness. The influence of surface roughness on structural properties and surface morphology of ZnO thin films was investigated by X-ray diffraction (XRD) and atom force microscopy (AFM), respectively. Only on the nanocrystalline and free-standing diamond substrates, ZnO films with preferential c-axis orientation and smooth surface were obtained.

Preparation of (111)-Oriented Pt Electrode Films with Quasi-Monocrystal Properties on MgO/TiN Buffered Si(100) by PLD

2007 ◽  
Vol 280-283 ◽  
pp. 823-826 ◽  
Author(s):  
Tong Lai Chen ◽  
Xiao Min Li
Keyword(s):  
High Energy ◽  
Layer Growth ◽  
Atomic Scale ◽  
Layer By Layer ◽  
X Ray Diffraction ◽  
Pt Electrode ◽  
Force Microscopy ◽  
Atomic Force

Atomic-scale smooth Pt electrode films have been deposited on MgO/TiN buffered Si (100) by the pulsed laser deposition (PLD) technique. The whole growth process of the multilayer films was monitored by using in-situ reflection high energy electron diffraction (RHEED) apparatus. The Pt/MgO/TiN/Si(100) stacked structure was also characterized by X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM). The HREED observations show that the growth mode of the Pt electrode film is 2D layer-by-layer growth. It is found that the (111)-oriented Pt electrode film has a crystallinity comparable to that of monocrystals. The achievement of the quasi-single-crystal Pt electrode film with an atomic-scale smooth surface is ascribed to the improved crystalline quality of the MgO film.

The Refractive Index and Other Properties of Doped ZnO films

2003 ◽  
Vol 764 ◽  
Author(s):  
A. L. Cai ◽  
J. F. Muth ◽  
H. L. Porter ◽  
A. Kvit ◽  
J. Narayan
Keyword(s):  
Zinc Oxide ◽  
Refractive Index ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Refractive Index Measurement ◽  
Force Microscopy ◽  
Sapphire Substrates ◽  
Atomic Force ◽  
Transmission Electron ◽  
Index Measurement

AbstractOrdinary and extraordinary indices of refraction, film thickness and waveguide mode information of zinc oxide, zinc oxide doped with nitrogen and zinc oxide doped with tellurium were measured by using a prism coupling waveguide technique. The films were grown on c-axis sapphire substrates by pulsed laser deposition (PLD). High accuracy waveguide measurements show that the ordinary and extraordinary indices of refraction of ZnO samples change with the introduction of nitrogen or tellurium. The densification of films with annealing could also be tracked with precision refractive index measurement. The crystal structure and the optical properties of the films were also characterized by using x-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy (AFM) and cathodoluminescence (CL).

Structural and Optical Properties of InAsSbBi Grown by Molecular Beam Epitaxy on Offcut GaSb Substrates

Photonics ◽  
2021 ◽  
Vol 8 (6) ◽  
pp. 215
Author(s):  
Rajeev R. Kosireddy ◽  
Stephen T. Schaefer ◽  
Marko S. Milosavljevic ◽  
Shane R. Johnson
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Optical Quality ◽  
X Ray Diffraction ◽  
Interface Quality ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Lateral Variations

Three InAsSbBi samples are grown by molecular beam epitaxy at 400 °C on GaSb substrates with three different offcuts: (100) on-axis, (100) offcut 1° toward [011], and (100) offcut 4° toward [011]. The samples are investigated using X-ray diffraction, Nomarski optical microscopy, atomic force microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The InAsSbBi layers are 210 nm thick, coherently strained, and show no observable defects. The substrate offcut is not observed to influence the structural and interface quality of the samples. Each sample exhibits small lateral variations in the Bi mole fraction, with the largest variation observed in the on-axis growth. Bismuth rich surface droplet features are observed on all samples. The surface droplets are isotropic on the on-axis sample and elongated along the [011¯] step edges on the 1° and 4° offcut samples. No significant change in optical quality with offcut angle is observed.

scholarly journals Ultrafine metal-polymer catalysts based on polyconjugated systems for Fisher–Tropsch synthesis

2020 ◽  
Vol 92 (6) ◽  
pp. 977-984
Author(s):  
Mayya V. Kulikova ◽  
Albert B. Kulikov ◽  
Alexey E. Kuz’min ◽  
Anton L. Maximov
Keyword(s):  
Tropsch Synthesis ◽  
X Ray Diffraction ◽  
Fischer Tropsch ◽  
Force Microscopy ◽  
Composite Catalysts ◽  
Fe Catalyst ◽  
Atomic Force ◽  
And Function ◽  
Metal Polymer

AbstractFor previously studied Fischer–Tropsch nanosized Fe catalyst slurries, polymer compounds with or without polyconjugating structures are used as precursors to form the catalyst nanomatrix in situ, and several catalytic experiments and X-ray diffraction and atomic force microscopy measurements are performed. The important and different roles of the paraffin molecules in the slurry medium in the formation and function of composite catalysts with the two types of aforementioned polymer matrices are revealed. In the case of the polyconjugated polymers, the alkanes in the medium are “weakly” coordinated with the metal-polymer composites, which does not affect the effectiveness of the polyconjugated polymers. Otherwise, alkane molecules form a “tight” surface layer around the composite particles, which create transport complications for the reagents and products of Fischer-Tropsch synthesis and, in some cases, can change the course of the in situ catalyst formation.

Effect of V/III Ratio on the Properties of GaN Layers Grown by Molecular Beam Epitaxy Using NH3

1998 ◽  
Vol 512 ◽  
Author(s):  
N. Grandjean ◽  
M. Leroux ◽  
J. Massies ◽  
M. Mesrine ◽  
P. Lorenzini
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Flux Ratio ◽  
Buffer Layers ◽  
Force Microscopy ◽  
Sapphire Substrates ◽  
Atomic Force ◽  
Piezoelectric Field ◽  
Secondary Ion

ABSTRACTAmmonia as nitrogen precursor has been used to grow III-V nitrides by molecular beam epitaxy (MBE) on c-plane sapphire substrates. The efficiency of NH3 has been evaluated allowing the determination of the actual V/III flux ratio used during the GaN growth. The effects of the V/III ratio variation on the GaN layer properties have been investigated by photoluminescence (PL), Hall measurements, atomic force microscopy (AFM), and secondary ion mass spectroscopy (SIMS). It is found that a high V/III ratio leads to the best material quality. Optimized GaN thick buffer layers have been used to grow GaN/AlGaN quantum well (QW) heterostructures. Their PL spectra exhibit well resolved emission peaks for QW thicknesses varying from 3 to 15 monolayers. From the variation of the QW energies as a function of well width, a piezoelectric field of 450 kV/cm is deduced.

scholarly journals Dielectric Function of AlN Grown on Si (111) by MBE

1999 ◽  
Vol 572 ◽  
Author(s):  
Stefan Zollner ◽  
Atul Konkar ◽  
R. B. Gregory ◽  
S. R. Wilson ◽  
S. A. Nikishin ◽  
...  
Keyword(s):  
Molecular Beam ◽  
Buffer Layers ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
Growth Morphology ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Dimensional Growth ◽  
Peak Widths

ABSTRACTWe measured the ellipsometric response from 0.7–5.4 eV of c-axis oriented AlN on Si (111) grown by molecular beam epitaxy. We determine the film thicknesses and find that for our AlN the refractive index is about 5–10% lower than in bulk AlN single crystals. Most likely, this discrepancy is due to a low film density (compared to bulk AlN), based on measurements using Rutherford backscattering. The films were also characterized using atomic force microscopy and x-ray diffraction to study the growth morphology. We find that AlN can be grown on Si (111) without buffer layers resulting in truely two-dimensional growth, low surface roughness, and relatively narrow x-ray peak widths.

Large Area Supersonic Jet Epitaxy of AlN, GaN, and SiC on Silicon

1996 ◽  
Vol 449 ◽  
Author(s):  
L.J. Lauhon ◽  
S. A. Ustin ◽  
W. Ho
Keyword(s):  
Supersonic Jet ◽  
X Ray Diffraction ◽  
Large Area ◽  
Free Jets ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Supersonic Jet Epitaxy ◽  
Carrier Gases

ABSTRACTAlN, GaN, and SiC thin films were grown on 100 mm diameter Si(111) and Si(100) substrates using Supersonic Jet Epitaxy (SJE). Precursor gases were seeded in lighter mass carrier gases and free jets were formed using novel slit-jet apertures. The jet design, combined with substrate rotation, allowed for a uniform flux distribution over a large area of a 100 mm wafer at growth pressures of 1–20 mTorr. Triethylaluminum, triethylgailium, and ammonia were used for nitride growth, while disilane, acetylene, and methylsilane were used for SiC growth. The films were characterized by in situ optical reflectivity, x-ray diffraction (XRD), atomic force microscopy (AFM), and spectroscopic ellipsometry (SE).

Properties of Nano-ZnO Films Deposited by RF Magnetron Sputtering for SAW Biosensors

2011 ◽  
Vol 418-420 ◽  
pp. 293-296
Author(s):  
Qiu Yun Fu ◽  
Peng Cheng Yi ◽  
Dong Xiang Zhou ◽  
Wei Luo ◽  
Jian Feng Deng
Keyword(s):  
Magnetron Sputtering ◽  
Deposition Time ◽  
Rf Magnetron Sputtering ◽  
Zno Films ◽  
X Ray Diffraction ◽  
Zno Film ◽  
Nano Zno ◽  
Axis Orientation ◽  
X Ray

Abstract. In this article, nano-ZnO films were deposited on SiO2/Si (100) substrates by RF (radio frequency) magnetron sputtering using high purity (99.99%) ZnO target. The effects of deposition time and annealing temperature have been investigated. XRD (X-ray diffraction) and FSEM (Field Emission Scanning Electron Microscopy) were employed to characterize the quality of the films. The results show that the ZnO film with thickness of 600nm annealed at 900°C has higher quality of both C-axis orientation and crystallization. And for the Zone film with thickness of 300nm annealed at 850°C, the quality of both C-axis orientation and crystallization is higher than that annealed at 900°C and 950°C.

Sign in / Sign up

Export Citation Format

Share Document