X-ray Microbeam Diffraction Measurements in Polycrystalline Aluminum and Copper Thin Films

2003 ◽  
Vol 795 ◽  
Author(s):  
L. E. Moyer ◽  
G. S. Cargill ◽  
W. Yang ◽  
B. C. Larson ◽  
G. E. Ice
Keyword(s):  
Thin Films ◽  
Crystallographic Orientation ◽  
Grain Orientation ◽  
Strain Tensor ◽  
Polycrystalline Aluminum ◽  
Thermally Induced ◽  
X Ray ◽  
Glass Substrates ◽  
Orientation Mapping ◽  
Residual Strains

ABSTRACTThermally induced residual strains in polycrystalline Cu and Al films on single crystal Si and glass substrates, respectively, have been examined on a grain-by-grain basis by x-ray microbeam diffraction. The crystallographic orientation and the deviatoric strain tensor, εij*, are determined for each grain by white beam Laue diffraction. From grain orientation mapping and strain tensor measurements, information is obtained about the distributions of strains for similarly oriented grains, about strain variations within single grains, and about grain-to-grain correlations of strains. This type of information may be useful in developing and testing theories for intergrain effects in strain evolution in polycrystals.

X- ray diffraction and dielectric properties of PbSe thin films

2019 ◽  
Vol 15 (34) ◽  
pp. 1-14
Author(s):  
Bushra A. Hasan
Keyword(s):  
Thin Films ◽  
Thermal Activation ◽  
Thermal Evaporation ◽  
Thermal Activation Energy ◽  
Dielectric Constants ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Thermal Evaporation Method ◽  
X Ray ◽  
Glass Substrates

Lead selenide PbSe thin films of different thicknesses (300, 500, and 700 nm) were deposited under vacuum using thermal evaporation method on glass substrates. X-ray diffraction measurements showed that increasing of thickness lead to well crystallize the prepared samples, such that the crystallite size increases while the dislocation density decreases with thickness increasing. A.C conductivity, dielectric constants, and loss tangent are studied as function to thickness, frequency (10kHz-10MHz) and temperatures (293K-493K). The conductivity measurements confirm confirmed that hopping is the mechanism responsible for the conduction process. Increasing of thickness decreases the thermal activation energy estimated from Arhinus equation is found to decrease with thickness increasing. The increase of thickness lead to reduce the polarizability α while the increasing of temperature lead to increase α.

scholarly journals Reactive Dual Magnetron Sputtering: A Fast Method for Preparing Stoichiometric Microcrystalline ZnWO4 Thin Films

Surfaces ◽  
2021 ◽  
Vol 4 (2) ◽  
pp. 106-114
Author(s):  
Yannick Hermans ◽  
Faraz Mehmood ◽  
Kerstin Lakus-Wollny ◽  
Jan P. Hofmann ◽  
Thomas Mayer ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Fast Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Post Annealing ◽  
Rf Signal ◽  
First Time

Thin films of ZnWO4, a promising photocatalytic and scintillator material, were deposited for the first time using a reactive dual magnetron sputtering procedure. A ZnO target was operated using an RF signal, and a W target was operated using a DC signal. The power on the ZnO target was changed so that it would match the sputtering rate of the W target operated at 25 W. The effects of the process parameters were characterized using optical spectroscopy, X-ray diffraction, and scanning electron microscopy, including energy dispersive X-ray spectroscopy as well as X-ray photoelectron spectroscopy. It was found that stoichiometric microcrystalline ZnWO4 thin films could be obtained, by operating the ZnO target during the sputtering procedure at a power of 55 W and by post-annealing the resulting thin films for at least 10 h at 600 °C. As FTO coated glass substrates were used, annealing led as well to the incorporation of Na, resulting in n+ doped ZnWO4 thin films.

Effect of Substrate Temperature on the Electrochromic Properties of Cobalt Hydroxide Thin Films Prepared by Reactive Sputtering

2011 ◽  
Vol 1328 ◽  
Author(s):  
KyoungMoo Lee ◽  
Yoshio Abe ◽  
Midori Kawamura ◽  
Hidenobu Itoh
Keyword(s):  
Thin Films ◽  
Substrate Temperature ◽  
Indium Tin Oxide ◽  
Large Change ◽  
Amorphous Structure ◽  
Cobalt Hydroxide ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Substrate Temperatures

ABSTRACTCobalt hydroxide thin films with a thickness of 100 nm were deposited onto glass, Si and indium tin oxide (ITO)-coated glass substrates by reactively sputtering a Co target in H2O gas. The substrate temperature was varied from -20 to +200°C. The EC performance of the films was investigated in 0.1 M KOH aqueous solution. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy of the samples indicated that Co3O4 films were formed at substrate temperatures above 100°C, and amorphous CoOOH films were deposited in the range from 10 to -20°C. A large change in transmittance of approximately 26% and high EC coloration efficiency of 47 cm2/C were obtained at a wavelength of 600 nm for the CoOOH thin film deposited at -20°C. The good EC performance of the CoOOH films is attributed to the low film density and amorphous structure.

Effects of Surface Energy on the Microstructures of Thin Sb Films

1990 ◽  
Vol 202 ◽  
Author(s):  
L. H. Chou ◽  
M. C. Kuo
Keyword(s):  
Electron Microscopy ◽  
Surface Energy ◽  
Grain Growth ◽  
Grain Orientation ◽  
Thermal Evaporation ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates ◽  
Transmission Electron ◽  
Diffraction Peaks

ABSTRACTThin Sb films have been prepared on glass substrates by rapid thermal evaporation. Films with thicknesses varied from 260 Å to 1300Å were used for the study. X-ray diffraction data showed that for films deposited at room substrate temperature, an almost random grain orientation was observed for films of 1300 Å thick and a tendency for preferred grain orientation was observed as films got thinner. For films of 260 Å thick, only two x-ray diffraction peaks--(003) and (006) were observed. After thermal annealing, secondary grains grew to show preferred orientation in all the films. This phenomenon was explained by surface-energy-driven secondary grain growth. This paper reports the effects of annealing time and film thickness on the secondary grain growth and the evolution of thin Sb film microstmctures. Transmission electron microscopy (TEM) and x-ray diffraction were used to characterize the films.

scholarly journals Comparative Study of ZnO Thin Films Grown on Quartz Glass and Sapphire (001) Substrates by Means of Magnetron Sputtering and High-Temperature Annealing

2019 ◽  
Vol 9 (21) ◽  
pp. 4509
Author(s):  
Weijia Yang ◽  
Fengming Wang ◽  
Zeyi Guan ◽  
Pengyu He ◽  
Zhihao Liu ◽  
...  
Keyword(s):  
Thin Films ◽  
High Temperature ◽  
Magnetron Sputtering ◽  
Comparative Study ◽  
Quartz Glass ◽  
Photoelectron Spectroscopy ◽  
Zno Thin Films ◽  
High Temperature Annealing ◽  
X Ray ◽  
Glass Substrates

In this work, we reported a comparative study of ZnO thin films grown on quartz glass and sapphire (001) substrates through magnetron sputtering and high-temperature annealing. Firstly, the ZnO thin films were deposited on the quartz glass and sapphire (001) substrates in the same conditions by magnetron sputtering. Afterwards, the sputtered ZnO thin films underwent an annealing process at 600 °C for 1 h in an air atmosphere to improve the quality of the films. X-ray diffraction, scanning electron microscopy, atomic force microscopy, X-ray photoelectron spectroscopy (XPS), ultraviolet-visible spectra, photoluminescence spectra, and Raman spectra were used to investigate the structural, morphological, electrical, and optical properties of the both as-received ZnO thin films. The ZnO thin films grown on the quartz glass substrates possess a full width of half maximum value of 0.271° for the (002) plane, a surface root mean square value of 0.50 nm and O vacancies/defects of 4.40% in the total XPS O 1s peak. The comparative investigation reveals that the whole properties of the ZnO thin films grown on the quartz glass substrates are comparable to those grown on the sapphire (001) substrates. Consequently, ZnO thin films with high quality grown on the quartz glass substrates can be achieved by means of magnetron sputtering and high-temperature annealing at 600 °C.

Electrochemical Deposition and Characterization of Cd-Fe-Se Thin Films

2009 ◽  
Vol 68 ◽  
pp. 69-76 ◽  
Author(s):  
S. Thanikaikarasan ◽  
T. Mahalingam ◽  
K. Sundaram ◽  
Tae Kyu Kim ◽  
Yong Deak Kim ◽  
...  
Keyword(s):  
Thin Films ◽  
Hexagonal Structure ◽  
X Rays ◽  
X Ray Diffraction ◽  
X Ray ◽  
Iron Selenide ◽  
Glass Substrates ◽  
Diffraction Patterns ◽  
Cadmium Iron Selenide ◽  
Deposited Films

Cadmium iron selenide (Cd-Fe-Se) thin films were deposited onto tin oxide (SnO2) coated conducting glass substrates from an aqueous electrolytic bath containing CdSO4, FeSO4 and SeO2 by potentiostatic electrodeposition. The deposition potentials of Cadmium (Cd), Iron (Fe), Selenium (Se) and Cadmium-Iron-Selenide (Cd-Fe-Se) were determined from linear cathodic polarization curves. The deposited films were characterized by x-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive analysis by x-rays (EDX) and optical absorption techniques, respectively. X-ray diffraction patterns shows that the deposited films are found to be hexagonal structure with preferential orientation along (100) plane. The effect of FeSO4 concentration on structural, morphological, compositional and optical properties of the films are studied and discussed in detail.

Influence of Deposition Time and Source-Substrate Distance on Properties of CdTe Thin Films Using Close-Spaced Sublimation at Higher Source Temperature

2013 ◽  
Vol 716 ◽  
pp. 325-327
Author(s):  
Xiao Yan Dai ◽  
Cheng Wu Shi ◽  
Yan Ru Zhang ◽  
Min Yao
Keyword(s):  
Thin Films ◽  
Deposition Time ◽  
Near Infrared ◽  
Soda Lime ◽  
Soda Lime Glass ◽  
X Ray ◽  
Source Temperature ◽  
Glass Substrates ◽  
Substrate Distance ◽  
Cdte Thin Films

In this paper, CdTe thin films were deposited on soda-lime glass substrates using CdTe powder as a source by close-spaced sublimation at higher source temperature of 700°C. The influence of the deposition time and the source-substrate distance on the chemical composition, crystal phase, surface morphology and optical band gap of CdTe thin films was systemically investigated by energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscope and the ultraviolet-visible-near infrared absorption spectra, respectively. At the deposition time of 60 min and the source-substrate distance of 5 mm, the CdTe thin films had pyramid appearance with the grain size of 15 μm.

Synthesis and Characterization of Nb-Doped TiO2 Thin Films Prepared by RF Magnetron Sputtering

2015 ◽  
Vol 1117 ◽  
pp. 139-142 ◽  
Author(s):  
Marius Dobromir ◽  
Radu Paul Apetrei ◽  
A.V. Rogachev ◽  
Dmitry L. Kovalenko ◽  
Dumitru Luca
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Rf Magnetron Sputtering ◽  
X Ray ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Diffraction Patterns

Amorphous Nb-doped TiO2 thin films were deposited on (100) Si and glass substrates at room temperature by RF magnetron sputtering and a mosaic-type Nb2O5-TiO2 sputtering target. To adjust the amount of the niobium dopant in the film samples, appropriate numbers of Nb2O5 pellets were placed on the circular area of the magnetron target with intensive sputtering. By adjusting the discharge conditions and the number of niobium oxide pellets, films with dopant content varying between 0 and 16.2 at.% were prepared, as demonstrated by X-ray photoelectron spectroscopy data. The X-ray diffraction patterns of the as-deposited samples showed the lack of crystalline ordering in the samples. Surfaces roughness and energy band gap values increase with dopant concentration, as showed by atomic force microscopy and UV-Vis spectroscopy measurements.

INVESTIGATING ANNEALING EFFECT ON OPTICAL PROPERTIES OF Cd0.8Zn0.2S THIN FILMS

2014 ◽  
Vol 21 (05) ◽  
pp. 1450073 ◽  
Author(s):  
SOMAYEH AZIZI ◽  
HAMID REZAGHOLIPOUR DIZAJI ◽  
MOHAMMAD HOSSEIN EHSANI ◽  
SEYED FEYZOLAH GHAVAMI MIRMAHALLE
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Hexagonal Wurtzite Structure ◽  
Band Gap Energy ◽  
Annealing Effect ◽  
Thin Layers ◽  
Optical Parameters ◽  
Thermal Evaporation Method ◽  
X Ray ◽  
Glass Substrates

Cd 0.8 Zn 0.2 S thin films deposited on glass substrates by thermal evaporation method were annealed at different temperatures for the first time in order to investigate annealing effect on optical properties. The compositional, structural of nanoparticles precursor synthesized using microwave irradiation method and optical properties of the films were studied using energy dispersive X-ray (EDX), X-ray diffraction, transmission electron microscopy (TEM), and UV-visible spectrophotometer techniques. The annealed films were found to have hexagonal Wurtzite structure with strong preferential orientation along the (002) diffraction peak. Important optical parameters such as extinction coefficient and refractive index revealed the effect of heat treatment on the deposited thin layers. A reduction in the band gap energy from 2.41 eV to 2.29 eV was observed for the annealed samples.

Sign in / Sign up

Export Citation Format

Share Document