Structural Characterization of a Plutonium Sequestering Agent Complex by Synchrotron X-Ray Diffraction

2006 ◽  
Vol 986 ◽  
Author(s):  
Anne E. V. Gorden ◽  
G. Szigethy ◽  
D. K. Shuh ◽  
B. E. F. Tiedemann ◽  
J. Xu ◽  
...  
Keyword(s):  
National Laboratory ◽  
Selective Extraction ◽  
Biological Transport ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selective Ligand ◽  
Detailed Evaluation ◽  
Biomimetic Approach ◽  
Solid State Structures

AbstractNew ligands and materials are required that can coordinate, sense, and purify actinides for selective extraction and reduction of toxic, radioactive wastes from the mining and purification of actinides. The similarities in the chemical, biological transport, and distribution properties of Fe(III) and Pu(IV) inspired a biomimetic approach to the development of sequestering agents for actinides. A detailed evaluation of the structure and bonding of actinide coordinating ligands like these is important for the design of new selective ligand systems. Knowing the difficulty with working with the crystals resulting from these ligand systems and safe handling considerations for working with Pu, procedures were developed that utilize the Advanced Light Source of Lawrence Berkeley National Laboratory to determine the solid-state structures of Pu complexes by X-ray diffraction.

Unprecedented transformation of [I−·I3−] to [I42−] polyiodides in the solid state: structures, phase transitions and characterization of dipyrazolium iodide triiodide

2015 ◽  
Vol 44 (42) ◽  
pp. 18447-18458 ◽  
Author(s):  
M. Węcławik ◽  
P. Szklarz ◽  
W. Medycki ◽  
R. Janicki ◽  
A. Piecha-Bisiorek ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Phase Transitions ◽  
Solid State ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Solid State Structures

Dipyrazolium iodide triiodide, [C3N2H5+]2[I−·I3−], has been synthesized and studied by means of X-ray diffraction, differential scanning calorimetry, dielectric measurements, and UV-Vis spectroscopy.

Synthesis and Structural Characterization of Bis(aziridine) Cobalt(II), Zinc(II) and Palladium(II) Complexes

2007 ◽  
Vol 62 (8) ◽  
pp. 1095-1101 ◽  
Author(s):  
J. Nicolas Roedel ◽  
Roman Bobka ◽  
Max Pfister ◽  
Martin Rieger ◽  
Bernd Neumann ◽  
...  
Keyword(s):  
Solid State ◽  
Molar Ratio ◽  
Tetrahedral Coordination ◽  
X Ray Diffraction ◽  
Metal Chlorides ◽  
X Ray ◽  
Square Planar ◽  
Solid State Structures ◽  
Planar Geometries

The reactions of anhydrous metal chlorides MCl2 [M = Co(II), Zn(II), Pd(II)] with aziridines (az) in CH2Cl2 at r. t. in a 1 : 5 molar ratio afforded the bis(aziridine)dichloro complexes M(az)2Cl2. After purification, all complexes were fully characterized. The solid state structures were determined using single crystal X-ray diffraction, and showed tetrahedral coordination geometries for the Co(II) and Zn(II) centers and trans-configurated square planar geometries for Pd(II).

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

High Resolution Replication of Organoclay Surfaces

1982 ◽  
Vol 40 ◽  
pp. 576-577
Author(s):  
W. W. Barker ◽  
W. E. Rigsby ◽  
V. J. Hurst ◽  
W. J. Humphreys
Keyword(s):  
Clay Mineral ◽  
Organic Molecule ◽  
Organic Molecules ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Naturally Occurring ◽  
Silicate Layers ◽  
Mineral Identification

Experimental clay mineral-organic molecule complexes long have been known and some of them have been extensively studied by X-ray diffraction methods. The organic molecules are adsorbed onto the surfaces of the clay minerals, or intercalated between the silicate layers. Natural organo-clays also are widely recognized but generally have not been well characterized. Widely used techniques for clay mineral identification involve treatment of the sample with H2 O2 or other oxidant to destroy any associated organics. This generally simplifies and intensifies the XRD pattern of the clay residue, but helps little with the characterization of the original organoclay. Adequate techniques for the direct observation of synthetic and naturally occurring organoclays are yet to be developed.

Synthesis and characterization of TiN / Ti / AISI 410 coatings

2018 ◽  
Vol 2 (1) ◽  
pp. 7
Author(s):  
S Chirino ◽  
Jaime Diaz ◽  
N Monteblanco ◽  
E Valderrama
Keyword(s):  
Synthesis And Characterization ◽  
Photoemission Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Columnar Grains ◽  
Tin Thin Films ◽  
Steel Aisi ◽  
Interacting Surfaces ◽  
Stainless Steel Aisi

The synthesis and characterization of Ti and TiN thin films of different thicknesses was carried out on a martensitic stainless steel AISI 410 substrate used for tool manufacturing. The mechanical parameters between the interacting surfaces such as thickness, adhesion and hardness were measured. By means of the scanning electron microscope (SEM) the superficial morphology of the Ti/TiN interface was observed, finding that the growth was of columnar grains and by means of EDAX the existence of titanium was verified.  Using X-ray diffraction (XRD) it was possible to observe the presence of residual stresses (~ -3.1 GPa) due to the different crystalline phases in the coating. Under X-ray photoemission spectroscopy (XPS) it was possible to observe the molecular chemical composition of the coating surface, being Ti-N, Ti-N-O and Ti-O the predominant ones.

Studies on the Preparation, Characterization and Solubility of -Cyclodextrin-Roxythromycin Inclusion Complexes

2009 ◽  
Vol 2 (2) ◽  
pp. 523-530
Author(s):  
D. Nagasamy Venkatesh ◽  
S. Karthick ◽  
M. Umesh ◽  
G. Vivek ◽  
R.M. Valliappan ◽  
...  
Keyword(s):  
Dissolution Rate ◽  
Inclusion Complexes ◽  
Phase Solubility ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ir Studies ◽  
Poorly Soluble ◽  
Poorly Soluble Drug

Roxythromycin/ β-cyclodextrin (Roxy/ β-CD) dispersions were prepared with a view to study the influence of β-CD on the solubility and dissolution rate of this poorly soluble drug. Phase-solubility profile indicated that the solubility of roxythromycin was significantly increased in the presence of β-cyclodextrin and was classified as AL-type, indicating the 1:1 stoichiometric inclusion complexes. Physical characterization of the prepared systems was carried out by differential scanning calorimetry (DSC), X-ray diffraction studies (XRD) and IR studies. Solid state characterization of the drug β-CD binary system using XRD, FTIR and DSC revealed distinct loss of drug crystallinity in the formulation, ostensibly accounting for enhancement of dissolution rate.

New Coordination Compounds of Fe(III) with Organic Ligands

2009 ◽  
Vol 59 (12) ◽  
Author(s):  
Mihaela Flondor ◽  
Ioan Rosca ◽  
Doina Sibiescu ◽  
Mihaela-Aurelia Vizitiu ◽  
Daniel-Mircea Sutiman ◽  
...  
Keyword(s):  
Chemical Analysis ◽  
Complex Compounds ◽  
Organic Ligands ◽  
X Ray Diffraction ◽  
X Ray ◽  
Elemental Chemical Analysis ◽  
Structural Formulae ◽  
Paramagnetic Properties

In this paper the synthesis and the study of some complex compounds of Fe(III) with ligands derived from: 2-(4-chloro-phenylsulfanyl)-1-(2-hydroxy-3,5-diiodo-phenyl)-ethanone (HL1), 1-(3,5-dibromo-2-hydroxy-phenyl)-2-phenylsulfanyl-ethanone(HL2), and 2-(4-chloro-phenylsulfanyl)-1-(3,5-dibromo-2-hydroxy-phenyl)-ethanone (HL3) is presented. The characterization of these complexes is based on method as: the elemental chemical analysis, IR and ESR spectroscopy, M�ssbauer, the thermogravimetric analysis and X-ray diffraction. Study of the IR and chemical analysis has evidenced that the precipitates form are a complexes and the combination ratio of M:L is 1:2. The central atoms of Fe(III) presented paramagnetic properties and a octaedric hybridization. Starting from this precipitation reactions, a method for the gravimetric determination of Fe(III) with this organic ligands has been possible. Based on the experimental data on literature indications, the structural formulae of the complex compounds are assigned.

scholarly journals New Insights into the Crystal Chemistry of Elpidite, Na2Zr[Si6O15]·3H2O and (Na1+YCax□1−X−Y)Σ=2Zr[Si6O15]·(3−X)H2O, and Ab Initio Modeling of IR Spectra

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2160
Author(s):  
Alexander Bogdanov ◽  
Ekaterina Kaneva ◽  
Roman Shendrik
Keyword(s):  
Ir Spectra ◽  
Structural Models ◽  
Chemical Characterization ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Special Group ◽  
X Ray ◽  
Influence Of Water ◽  
Radioactive Species

Elpidite belongs to a special group of microporous zirconosilicates, which are of great interest due to their capability to uptake various molecules and ions, e.g., some radioactive species, in their structural voids. The results of a combined electron probe microanalysis and single-crystal X-ray diffraction study of the crystals of elpidite from Burpala (Russia) and Khan-Bogdo (Mongolia) deposits are reported. Some differences in the chemical compositions are observed and substitution at several structural positions within the structure of the compounds are noted. Based on the obtained results, a detailed crystal–chemical characterization of the elpidites under study was carried out. Three different structure models of elpidite were simulated: Na2ZrSi6O15·3H2O (related to the structure of Russian elpidite), partly Ca-replaced Na1.5Ca0.25ZrSi6O15·2.75H2O (close to elpidite from Mongolia), and a hypothetical CaZrSi6O15·2H2O. The vibration spectra of the models were obtained and compared with the experimental one, taken from the literature. The strong influence of water molecule vibrations on the shape of IR spectra of studied structural models of elpidite is discussed in the paper.

scholarly journals Electrospun Membranes Based on Polycaprolactone, Nano-Hydroxyapatite and Metronidazole

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 931
Author(s):  
Ioana-Codruţa Mirică ◽  
Gabriel Furtos ◽  
Ondine Lucaciu ◽  
Petru Pascuta ◽  
Mihaela Vlassa ◽  
...  
Keyword(s):  
Fiber Diameter ◽  
Maximum Load ◽  
Guided Bone Regeneration ◽  
Attenuated Total Reflectance ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Total Reflectance ◽  
X Ray ◽  
Electrospun Membranes

The aim of this research was to develop new electrospun membranes (EMs) based on polycaprolactone (PCL) with or without metronidazole (MET)/nano-hydroxyapatite (nHAP) content. New nHAP with a mean diameter of 34 nm in length was synthesized. X-ray diffraction (XRD) and attenuated total reflectance Fourier transform infrared spectroscopy (FTIR-ATR) were used for structural characterization of precursors and EMs. The highest mechanical properties (the force at maximum load, Young’s modulus and tensile strength) were found for the PCL membranes, and these properties decreased for the other samples in the following order: 95% PCL + 5% nHAP > 80% PCL + 20% MET > 75% PCL + 5% nHAP + 20% MET. The stiffness increased with the addition of 5 wt.% nHAP. The SEM images of EMs showed randomly oriented bead-free fibers that generated a porous structure with interconnected macropores. The fiber diameter showed values between 2 and 16 µm. The fiber diameter increased with the addition of nHAP filler and decreased when MET was added. New EMs with nHAP and MET could be promising materials for guided bone regeneration or tissue engineering.

Sign in / Sign up

Export Citation Format

Share Document