scholarly journals Spoofing Attack Detection Method for UAV Navigation System

2021 ◽  
Vol 20 (6) ◽  
pp. 1368-1394
Author(s):  
Elena Basan ◽  
Eugene Abramov ◽  
Anatoly Basyuk ◽  
Nikita Sushkin
Keyword(s):  
Low Cost ◽  
Satellite System ◽  
Attack Detection ◽  
Physical Parameters ◽  
Safe Navigation ◽  
Experimental Stand ◽  
Internal Parameters ◽  
Diagnosis Method ◽  
Global Navigation Satellite ◽  
Gps System

An implementation of methods for protecting unmanned aerial vehicles (UAVs) from spoofing attacks of the global positioning system (GPS) to ensure safe navigation is discussed in this paper. The Global Navigation Satellite System (GNSS) is widely used to locate UAVs and is by far the most popular navigation solution. This is due to the simplicity and relatively low cost of this technology, as well as the accuracy of the transmitted coordinates. However, there are many security threats to GPS navigation. Primarily this is due to the nature of the GPS signal, the signal is transmitted in the clear, so an attacker can block or tamper with it. This study analyzes the existing GPS protection methods. As part of the study, an experimental stand and scenarios of attacks on the UAV GPS system were developed. Data from the UAV flight logbook was collected and an analysis of cyber-physical parameters was carried out to see an effect of the attack on the on-board sensors readings. Based on this, a new method for detecting UAV anomalies was proposed, based on an analysis of changes in UAV internal parameters. This self-diagnosis method allows the UAV to independently assess the presence of changes in its subsystems and identify signs of a cyberattack. To detect an attack, the UAV collects data on changes in cyber-physical parameters over a certain period of time, then updates this data. As a result it is necessary for the UAV to determine the degree of difference between the two time series of the collected data. The greater the degree of difference between the updated data and the previous ones, the more likely the UAV is under attack.

scholarly journals A Self-Diagnosis Method for Detecting UAV Cyber Attacks Based on Analysis of Parameter Changes

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 509
Author(s):  
Elena Basan ◽  
Alexandr Basan ◽  
Alexey Nekrasov ◽  
Colin Fidge ◽  
Ján Gamec ◽  
...  
Keyword(s):  
Low Cost ◽  
Satellite System ◽  
Cyber Attacks ◽  
Safe Navigation ◽  
Experimental Stand ◽  
Internal Parameters ◽  
Diagnosis Method ◽  
System Data ◽  
Global Navigation Satellite ◽  
Gps System

We consider how to protect Unmanned Aerial Vehicles (UAVs) from Global Positioning System (GPS) spoofing attacks to provide safe navigation. The Global Navigation Satellite System (GNSS) is widely used for locating drones and is by far the most popular navigation solution. This is because of the simplicity and relatively low cost of this technology, as well as the accuracy of the transmitted coordinates. Nevertheless, there are many security threats to GPS navigation. These are primarily related to the nature of the GPS signal, as an intruder can jam and spoof the GPS signal. We discuss methods of protection against this type of attack and have developed an experimental stand and conducted scenarios of attacks on a drone’s GPS system. Data from the UAV’s flight log were collected and analyzed in order to see the attack’s impact on sensor readings. From this we identify a new method for detecting UAV anomalies by analyzing changes in internal parameters of the UAV. This self-diagnosis method allows a UAV to independently assess the presence of changes in its own subsystems indicative of cyber attacks.

scholarly journals Modified WiFi-RSS Fingerprint Technique to locate Indoors-Smartphones: FENG building at Koya University as a case study

2017 ◽  
Vol 2 (3) ◽  
pp. 212-217 ◽  
Author(s):  
Halgurd S. Maghdid ◽  
Ladeh Sardar Abdulrahman ◽  
Mohammed H. Ahmed ◽  
Azhin Tahir Sabir
Keyword(s):  
Global Positioning System ◽  
High Performance ◽  
Low Cost ◽  
Satellite System ◽  
Positioning System ◽  
Global Positioning ◽  
Accurate Position ◽  
Global Navigation Satellite ◽  
Gps System

Positioning system used for different purposes and different services, many researches are going on to find a more accurate position with low error within high performance. There are many localization solutions with different architectures, configurations, accuracies and reliabilities for both outdoors and indoors. For example, Global Navigation Satellite System (GNSS) technology has been used for outdoors.  Global Positioning System (GPS) is one of the most common outdoors tracking solutions in the world, for outdoors, however, when indoors; it could not be accurately tracked users by using a GPS system. This is because, when users enters into indoors the GPS signals will no longer available due to blocked by the roof of buildings and it is no longer considered as a viable option.  WiFi Positioning System (WPS) can be used as an alternative solution to define users’ position, especially when GPS signal is not available. Further, WPS is a low cost solution, because there is no need to deploying WiFi Access Points (WAPs) in the vicinity, as they are installed to access the Internet. In this paper, specifically, WiFi-RSS Fingerprinting technique is used to locate smartphones using WAPs signals with a modified calculation. The new modified calculation is to dynamic weighting of the WAPs RSS values based on the real-live indoors structure. The achieved positioning accuracy, based on several trial experiments, is up to 6 meters via the implemented algorithm in the MALTAB.

scholarly journals Design of a Multiband Global Navigation Satellite System Radio Frequency Interference Monitoring Front-End with Synchronized Secondary Sensors

Sensors ◽  
2018 ◽  
Vol 18 (8) ◽  
pp. 2594
Author(s):  
Aiden Morrison ◽  
Nadezda Sokolova ◽  
James Curran
Keyword(s):  
Radio Frequency ◽  
Global Navigation Satellite System ◽  
Low Cost ◽  
Satellite System ◽  
Radio Frequency Interference ◽  
Navigation Satellite ◽  
Inertial Measurement ◽  
Front End ◽  
Global Navigation ◽  
Global Navigation Satellite

This paper investigates the challenges of developing a multi-frequency radio frequency interference (RFI) monitoring and characterization system that is optimized for ease of deployment and operation as well as low per unit cost. To achieve this, we explore the design and development of a multiband global navigation satellite system (GNSS) front-end which is intrinsically capable of synchronizing side channel information from non-RF sensors, such as inertial measurement units and integrated power meters, to allow the simultaneous production of substantial amounts of sampled spectrum while also allowing low-cost, real-time monitoring and logging of detected RFI events. While the inertial measurement unit and barometer are not used in the RFI investigation discussed, the design features that provide for their precise synchronization with the RF sample stream are presented as design elements worth consideration. The designed system, referred to as Four Independent Tuners with Data-packing (FITWD), was utilized in a data collection campaign over multiple European and Scandinavian countries in support of the determination of the relative occurrence rates of L1/E1 and L5/E5a interference events and intensities where it proved itself a successful alternative to larger and more expensive commercial solutions. The dual conclusions reached were that it was possible to develop a compact low-cost, multi-channel radio frequency (RF) front-end that implicitly supported external data source synchronization, and that such monitoring systems or similar capabilities integrated within receivers are likely to be needed in the future due to the increasing occurrence rates of GNSS RFI events.

scholarly journals Kinematic PPP Using Mixed GPS/Glonass Single-Frequency Observations

2019 ◽  
Vol 54 (3) ◽  
pp. 97-112
Author(s):  
Mostafa Hamed ◽  
Ashraf Abdallah ◽  
Ashraf Farah
Keyword(s):  
Low Cost ◽  
Satellite System ◽  
Single Frequency ◽  
Future Research ◽  
Frequency Data ◽  
Dual Frequency ◽  
Trajectory Data ◽  
Average Improvement ◽  
Kinematic Ppp ◽  
Global Navigation Satellite

Abstract Nowadays, Precise Point Positioning (PPP) is a very popular technique for Global Navigation Satellite System (GNSS) positioning. The advantage of PPP is its low cost as well as no distance limitation when compared with the differential technique. Single-frequency receivers have the advantage of cost effectiveness when compared with the expensive dual-frequency receivers, but the ionosphere error makes a difficulty to be completely mitigated. This research aims to assess the effect of using observations from both GPS and GLONASS constellations in comparison with GPS only for kinematic purposes using single-frequency observations. Six days of the year 2018 with single-frequency data for the Ethiopian IGS station named “ADIS” were processed epoch by epoch for 24 hours once with GPS-only observations and another with GPS/GLONASS observations. In addition to “ADIS” station, a kinematic track in the New Aswan City, Aswan, Egypt, has been observed using Leica GS15, geodetic type, dual-frequency, GPS/GLONASS GNSS receiver and single-frequency data have been processed. Net_Diff software was used for processing all the data. The results have been compared with a reference solution. Adding GLONASS satellites significantly improved the satellite number and Position Dilution Of Precision (PDOP) value and accordingly improved the accuracy of positioning. In the case of “ADIS” data, the 3D Root Mean Square Error (RMSE) ranged between 0.273 and 0.816 m for GPS only and improved to a range from 0.256 to 0.550 m for GPS/GLONASS for the 6 processed days. An average improvement ratio of 24%, 29%, 30%, and 29% in the east, north, height, and 3D position components, respectively, was achieved. For the kinematic trajectory, the 3D position RMSE improved from 0.733 m for GPS only to 0.638 m for GPS/GLONASS. The improvement ratios were 7%, 5%, 28%, and 13% in the east, north, height, and 3D position components, respectively, for the kinematic trajectory data. This opens the way to add observations from the other two constellations (Galileo and BeiDou) for more accuracy in future research.

Securing the Automatic Identification System (AIS): Using public key cryptography to prevent spoofing whilst retaining backwards compatibility

2021 ◽  
pp. 1-13
Author(s):  
Gareth Wimpenny ◽  
Jan Šafář ◽  
Alan Grant ◽  
Martin Bransby
Keyword(s):  
Data Exchange ◽  
Situational Awareness ◽  
Public Key Cryptography ◽  
Satellite System ◽  
Public Key ◽  
Automatic Identification ◽  
Identification System ◽  
Automatic Identification System ◽  
Safe Navigation ◽  
Global Navigation Satellite

Abstract The civilian Automatic Identification System (AIS) has no inherent protection against spoofing. Spoofed AIS messages have the potential to interfere with the safe navigation of a vessel by, amongst other approaches, spoofing maritime virtual aids to navigation and/or differential global navigation satellite system (DGNSS) correction data conveyed across it. Acting maliciously, a single transmitter may spoof thousands of AIS messages per minute with the potential to cause considerable nuisance; compromising information provided by AIS intended to enhance the mariner's situational awareness. This work describes an approach to authenticate AIS messages using public key cryptography (PKC) and thus provide unequivocal evidence that AIS messages originate from genuine sources and so can be trusted. Improvements to the proposed AIS authentication scheme are identified which address a security weakness and help avoid false positives to spoofing caused by changes to message syntax. A channel loading investigation concludes that sufficient bandwidth is available to routinely authenticate all AIS messages whilst retaining backwards compatibility by carrying PKC ‘digital signatures’ in a separate VHF Data Exchange System (VDES) side channel.

scholarly journals Terrain changes from images acquired on opportunistic flights by SfM photogrammetry

2017 ◽  
Vol 11 (2) ◽  
pp. 827-840 ◽  
Author(s):  
Luc Girod ◽  
Christopher Nuth ◽  
Andreas Kääb ◽  
Bernd Etzelmüller ◽  
Jack Kohler
Keyword(s):  
Low Cost ◽  
Rapid Change ◽  
Satellite System ◽  
Light Transport ◽  
Area Of Interest ◽  
Accuracy And Precision ◽  
Global Navigation Satellite ◽  
The Cost ◽  
Gnss Data

Abstract. Acquiring data to analyse change in topography is often a costly endeavour requiring either extensive, potentially risky, fieldwork and/or expensive equipment or commercial data. Bringing the cost down while keeping the precision and accuracy has been a focus in geoscience in recent years. Structure from motion (SfM) photogrammetric techniques are emerging as powerful tools for surveying, with modern algorithm and large computing power allowing for the production of accurate and detailed data from low-cost, informal surveys. The high spatial and temporal resolution permits the monitoring of geomorphological features undergoing relatively rapid change, such as glaciers, moraines, or landslides. We present a method that takes advantage of light-transport flights conducting other missions to opportunistically collect imagery for geomorphological analysis. We test and validate an approach in which we attach a consumer-grade camera and a simple code-based Global Navigation Satellite System (GNSS) receiver to a helicopter to collect data when the flight path covers an area of interest. Our method is based and builds upon Welty et al. (2013), showing the ability to link GNSS data to images without a complex physical or electronic link, even with imprecise camera clocks and irregular time lapses. As a proof of concept, we conducted two test surveys, in September 2014 and 2015, over the glacier Midtre Lovénbreen and its forefield, in northwestern Svalbard. We were able to derive elevation change estimates comparable to in situ mass balance stake measurements. The accuracy and precision of our DEMs allow detection and analysis of a number of processes in the proglacial area, including the presence of thermokarst and the evolution of water channels.

scholarly journals GNSS-ISE: Instruction Set Extension for GNSS Baseband Processing

Sensors ◽  
2020 ◽  
Vol 20 (2) ◽  
pp. 465 ◽  
Author(s):  
Krzysztof Marcinek ◽  
Witold A. Pleskacz
Keyword(s):  
Flash Memory ◽  
Low Cost ◽  
Satellite System ◽  
Microprocessor System ◽  
Instruction Set ◽  
Advantages And Disadvantages ◽  
Wide Range ◽  
Instruction Set Extension ◽  
Baseband Processing ◽  
Global Navigation Satellite

This work presents the results of research toward designing an instruction set extension dedicated to Global Navigation Satellite System (GNSS) baseband processing. The paper describes the state-of-the-art techniques of GNSS receiver implementation. Their advantages and disadvantages are discussed. Against this background, a new versatile instruction set extension for GNSS baseband processing is presented. The authors introduce improved mechanisms for instruction set generation focused on multi-channel processing. The analytical approach used by the authors leads to the introduction of a GNSS-instruction set extension (ISE) for GNSS baseband processing. The developed GNSS-ISE is simulated extensively using PC software and field-programmable gate array (FPGA) emulation. Finally, the developed GNSS-ISE is incorporated into the first-in-the-world, according to the authors’ best knowledge, integrated, multi-frequency, and multi-constellation microcontroller with embedded flash memory. Additionally, this microcontroller may serve as an application processor, which is a unique feature. The presented results show the feasibility of implementing the GNSS-ISE into an embedded microprocessor system and its capability of performing baseband processing. The developed GNSS-ISE can be implemented in a wide range of applications including smart IoT (internet of things) devices or remote sensors, fostering the adaptation of multi-frequency and multi-constellation GNSS receivers to the low-cost consumer mass-market.

scholarly journals Testing Multi-Frequency Low-Cost GNSS Receivers for Geodetic Monitoring Purposes

Sensors ◽  
2020 ◽  
Vol 20 (16) ◽  
pp. 4375
Author(s):  
Veton Hamza ◽  
Bojan Stopar ◽  
Tomaž Ambrožič ◽  
Goran Turk ◽  
Oskar Sterle
Keyword(s):  
Low Cost ◽  
Base Point ◽  
Satellite System ◽  
Gnss Receivers ◽  
The Difference ◽  
Short Baselines ◽  
Height Component ◽  
Global Navigation Satellite ◽  
High Level ◽  
Positional Precision

Global Navigation Satellite System (GNSS) technology is widely used for geodetic monitoring purposes. However, in cases where a higher risk of receiver damage is expected, geodetic GNSS receivers may be considered too expensive to be used. As an alternative, low-cost GNSS receivers that are cheap, light, and prove to be of adequate quality over short baselines, are considered. The main goal of this research is to evaluate the positional precision of a multi-frequency low-cost instrument, namely, ZED-F9P with u-blox ANN-MB-00 antenna, and to investigate its potential for displacement detection. We determined the positional precision within static survey, and the displacement detection within dynamic survey. In both cases, two baselines were set, with the same rover point equipped with a low-cost GNSS instrument. The base point of the first baseline was observed with a geodetic GNSS instrument, whereas the second baseline was observed with a low-cost GNSS instrument. The results from static survey for both baselines showed comparable results for horizontal components; the precision was on a level of 2 mm or better. For the height component, the results show a better performance of low-cost instruments. This may be a consequence of unknown antenna calibration parameters for low-cost GNSS antenna, while statistically significant coordinates of rover points were obtained from both baselines. The difference was again more significant in the height component. For the displacement detection, a device was used that imposes controlled movements with sub-millimeter accuracy. Results, obtained on a basis of 30-min sessions, show that low-cost GNSS instruments can detect displacements from 10 mm upwards with a high level of reliability. On the other hand, low-cost instruments performed slightly worse as far as accuracy is concerned.

A Novel GNSS Attitude Determination Method Based on Primary Baseline Switching for A Multi-Antenna Platform

2020 ◽  
Vol 12 (5) ◽  
pp. 747
Author(s):  
Peng Zhang ◽  
Yinzhi Zhao ◽  
Huan Lin ◽  
Jingui Zou ◽  
Xinzhe Wang ◽  
...  
Keyword(s):  
Attitude Determination ◽  
Low Cost ◽  
Satellite System ◽  
Poor Quality ◽  
Integrated Navigation ◽  
Determination Method ◽  
Integrated Navigation System ◽  
Determination System ◽  
Vehicle Test ◽  
Global Navigation Satellite

The global navigation satellite system (GNSS)-based attitude determination system has attracted more and more attention with the advantages of having simplified algorithms, a low price and errors that do not accumulate over time. However, GNSS signals may have poor quality or lose lock in some epochs with the influence of signal fading and the multipath effect. When the direct attitude determination method is applied, the primary baseline may not be available (ambiguity is not fixed), leading to the inability of attitude determination. With the gradual popularization of low-cost receivers, making full use of spatial redundancy information of multiple antennas brings new ideas to the GNSS-based attitude determination method. In this paper, an attitude angle conversion algorithm, selecting an arbitrary baseline as the primary baseline, is derived. A multi-antenna attitude determination method based on primary baseline switching is proposed, which is performed on a self-designed embedded software and hardware platform. The proposed method can increase the valid epoch proportion and attitude information. In the land vehicle test, reference results output from a high-accuracy integrated navigation system were used to evaluate the accuracy and reliability. The results indicate that the proposed method is correct and feasible. The valid epoch proportion is increased by 16.2%, which can effectively improve the availability of attitude determination. The RMS of the heading, pitch and roll angles are 0.52°, 1.25° and 1.16°.

Sign in / Sign up

Export Citation Format

Share Document