scholarly journals Effect of Annealing Temperature on the Li\(^{ + }\) Ionic Conductivity of La\(_{0.67 - x}\)Li\(_{3x}\)TiO\(_{3 }\)

2009 ◽  
Vol 19 (4) ◽  
pp. 235-242
Author(s):  
Le Dinh Trong ◽  
Pham Duy Long ◽  
Nguyen Nang Dinh
Keyword(s):  
High Temperature ◽  
Ionic Conductivity ◽  
Thermal Treatment ◽  
Grain Boundary ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Boundary Conductivity ◽  
Impedance Measurements ◽  
Post Annealing ◽  
Reactive Milling

Perovskite La0.67-xLi3xTiO3 with x = 0.10, 0.11, 0.12 and 0.13 were firstly annealed at 800 oC then treated by reactive milling, followed by post-annealing at temperatures from 1100 to 1200oC. The crystalline structure of grain and grain-boundary were characterized by XRD and SEM. The impedance measurements showed that nanocrystalline La0.67-xLi3xTiO3 after being annealed at 1150 oC possessed a grain conductivity as high as 1.3×10-3 S.cm-1. The grain-boundary conductivity was enhanced one order in magnitude after annealing at temperature higher 1100oC and consists of 5.8×10-5 S.cm-1. The results have also showed the limitation of the adiabatic thermal treatment for the improvement of the grain-boundary conductivity and suggested the way to overcome the limitation by rapidly cooling the samples from the high temperature to room temperature.

scholarly journals Influence of Lithium Content on the Structure and Ionic Conductivity of Perovskite \(\mbox{La}_{(2/3) - x}\mbox{Li}_{3x}\mbox{TiO}_{3}\) Made by Double Mechanical Alloying Method

2014 ◽  
Vol 24 (3S1) ◽  
pp. 33-39
Author(s):  
Le Dinh Trong
Keyword(s):  
Activation Energy ◽  
Ionic Conductivity ◽  
Grain Boundary ◽  
Mechanical Alloying ◽  
Room Temperature ◽  
Lithium Content ◽  
Boundary Conductivity ◽  
Structural Modifications ◽  
Li Ion ◽  
Conductive Properties

Perovskite La\(_{(2/3) - x}\)Li\(_{3x}\)TiO\(_{3}\) samples with 0.06 \( \leq x \leq 0.15\) were prepared by a double mechanical alloying method. Structure and Li$^{ + }$-ion conductive properties of the La\(_{(2 / 3) - x}\)Li\(_{3x}\)TiO\(_{3}\) samples were investigated. Most of the analyzed perovskite samples exhibit a double unit cell. In these samples, a change of symmetry from tetragonal to orthorhombic is observed for sample with lithium content x = 0.06. Structural modifications were obtained mainly due to the cation vacancies ordering along the c-axis, which disappeared gradually when the lithium content increased. At room temperature, the maximum values of grains and grain boundaries conductivities of the La\(_{(2 / 3) - x}\)Li\(_{3x}\)TiO\(_{3}\) samples were found to be of \(1.5\times 10$^{ - 3}\) S/cm and \(5.8 \times 10^{ - 5}\) S/cm, respectively. The temperature dependence of ionic conductivity obeyed a non-Arrhenius behaviour. At temperature from 30 to 125\(^{\circ}\)C, the activation energy for grain and grain-boundary conductivity was found to be of $\sim $ 0.23 eV and $\sim $ 0.32 eV, respectively.

Increased Thermal Stability of Co-silicide Using Co-Ta Alloy Films

2001 ◽  
Vol 670 ◽  
Author(s):  
Min-Joo Kim ◽  
Hyo-Jick Choi ◽  
Dae-Hong Ko ◽  
Ja-Hum Ku ◽  
Siyoung Choi ◽  
...  
Keyword(s):  
Thermal Stability ◽  
High Temperature ◽  
Grain Boundary ◽  
Reaction Rate ◽  
Boundary Migration ◽  
Grain Boundary Migration ◽  
Alloy Films ◽  
Post Annealing ◽  
Alloy Process ◽  
Thermal Stability Of

ABSTRACTThe silicidation reactions and thermal stability of Co silicide formed from Co-Ta/Si systems have been investigated. In case of Co-Ta alloy process, the formation of low resistive CoSi2phase is delayed to about 660°C, as compared to conventional Co/Si system. Moreover, the presence of Ta in Co-Ta alloy films reduces the silicidation reaction rate, resulting in the strong preferential orientation in CoSi2 films. Upon high temperature post annealing in the furnace, the sheet resistance of Co-silicide formed from Co/Si systems increases significantly, while that of Co-Ta/Si systems maintains low. This is due to the formation of TaSi2 at the grain boundaries and surface of Co-silicide films, which prevents the grain boundary migration thereby slowing the agglomeration. Therefore, from our research, increased thermal stability of Co-silicide films was successfully obtained from Co-Ta alloy process.

scholarly journals Crystal Chemistry and Luminescence Properties of Eu-Doped Polycrystalline Hydroxyapatite Synthesized by Chemical Precipitation at Room Temperature

Crystals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 250 ◽  
Author(s):  
Francesco Baldassarre ◽  
Angela Altomare ◽  
Nicola Corriero ◽  
Ernesto Mesto ◽  
Maria Lacalamita ◽  
...  
Keyword(s):  
Fourier Transform ◽  
High Temperature ◽  
Inductively Coupled Plasma ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Chemical Precipitation ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled

Europium-doped hydroxyapatite Ca10(PO4)6(OH)2 (3% mol) powders were synthesized by an optimized chemical precipitation method at 25 °C, followed by drying at 120 °C and calcination at 450 °C and 900 °C. The obtained nanosized crystallite samples were investigated by means of a combination of inductively coupled plasma (ICP) spectroscopy, powder X-ray diffraction (PXRD), Fourier Transform Infrared (FTIR), Raman and photoluminescence (PL) spectroscopies. The Rietveld refinement in the hexagonal P63/m space group showed europium ordered at the Ca2 site at high temperature (900 °C), and at the Ca1 site for lower temperatures (120 °C and 450 °C). FTIR and Raman spectra showed slight band shifts and minor modifications of the (PO4) bands with increasing annealing temperature. PL spectra and decay curves revealed significant luminescence emission for the phase obtained at 900 °C and highlighted the migration of Eu from the Ca1 to Ca2 site as a result of increasing calcinating temperature.

Evaluation of Plastic Workability Limit of Magnesium Alloy by Cavitations in High Temperature Uni and Biaxial Test

2012 ◽  
Vol 735 ◽  
pp. 67-72
Author(s):  
Kunio Funami ◽  
Daisuke Yamashita ◽  
Kohji Suzuki ◽  
Masafumi Noda
Keyword(s):  
Fine Structure ◽  
High Temperature ◽  
Magnesium Alloy ◽  
Grain Boundary ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Az31 Magnesium Alloy ◽  
Temperature Deformation ◽  
Alloy Plate ◽  
Boundary Sliding

Abstract. This study examined the critical plastic formability limit of a fine-structure AZ31 magnesium alloy plate under warm and high temperature based on the strength of a magnesium alloy that has cavities at room temperature. The cyclic hot free-forging process as pre-form working following rolling at a light reduction ratio fabricated a fine-structure AZ31 magnesium alloy plate. The appearance of the cavities was examined in detail together with changes in the structure and preparation methods before further damage at high temperatures with increasing uni-and biaxial plastic deformation. The allowable deformation limit in the super plasticity process can be estimated from the strength of the deformed material and forming limit diagram (FLD) at room temperature. During high-temperature deformation, cavities are produced by stress concentrations at grain boundary triple points and striation bands due to grain boundary sliding. The cavitations growth behavior is dependent upon deformation conditions, and a high percentage of large cavities occupy the sample surface as a large amount of grain boundary sliding is present, i.e., as uniform elongation grows larger, the cavity size also increases. In a case where 200% uniaxial strain was applied to a fine-grained structure material at a temperature of 623K under a strain rate of 10-4s-1, the tensile strength at room temperature decreased about 13%, and elongation was 10% less, compared with that of a material to which no load was applied due to the influence of cavities. In a case of biaxial deformation, the values were 28% lower. It is possible to draw a FLD based on the cavity incidence fraction .

Influence of Al-Cu-Mn-Fe-Ti Alloy Composition and Production Parameters of Extruded Semi-Finished Products on their Structure and Mechanical Properties

2017 ◽  
Vol 265 ◽  
pp. 456-462 ◽  
Author(s):  
P.L. Reznik ◽  
Mikhail Lobanov
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Thermal Treatment ◽  
Low Temperature ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Ti Alloy ◽  
Low Temperature Annealing ◽  
Annealing Conditions ◽  
Concentration Changes

Studies have been conducted as to the effect of Cu, Mn, Fe concentration changes in Al-Cu-Mn-Fe-Ti alloy, the conditions of thermal and deformational treatment of ingots and extruded rods 40 mm in diameter on the microstructure, phase composition and mechanical properties. It has been determined that changing Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy to Al-6.5Cu-0.7Mn-0.11Fe-0.15Ti causes an increase in the strength characteristics of extruded rods at the room temperature both after molding and in tempered and aged conditions, irrespective of the conditions of thermal treatment of the initial ingot (low-temperature annealing 420 °С for 2 h, or high-temperature annealing at 530 °С for 12 h). Increasing the extruding temperature from 330 to 480 °С, along with increasing Cu, Mn and decreasing Fe in the alloy Al-Cu-Mn-Ti, is accompanied by the increased level of ultimate strength in a quenched condition by 25% to 410 MPa, irrespective of the annealing conditions of the original ingot. An opportunity to apply the Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy with low-temperature annealing at 420 °С for 2 h and the molding temperature of 330 °С has been found to produce rods where, in the condition of full thermal treatment (tempering at 535 °С + aging at 200 °С for 8 hours), a structure is formed that ensures satisfactory characteristics of high temperature strength by resisting to fracture for more than 100 hours at 300 °С and 70 MPa.

STRUCTURAL AND OPTICAL CHARACTERIZATION OF ZnO SINGLE CRYSTALLINE NANOBAMBOOS

2005 ◽  
Vol 19 (15n17) ◽  
pp. 2804-2810 ◽  
Author(s):  
LEI MIAO ◽  
SAKAE TANEMURA ◽  
YASUHIKO HAYASHI ◽  
MASAKI TANEMURA ◽  
RONGPING WANG ◽  
...  
Keyword(s):  
Room Temperature ◽  
Annealing Temperature ◽  
Optical Characterization ◽  
Growth Direction ◽  
Annealed Sample ◽  
Green Band ◽  
Post Annealing ◽  
High Resolution Tem ◽  
Post Annealing Temperature

ZnO nanobamboos and nanowires with diameters of 10–30 nm and lengths of 2–4 μm have been prepared by laser ablation in vacuum with precisely controlled pressure, growth and post-annealing temperature. XRD results show the annealed sample is hexagonal ZnO . Low-magnified TEM observation reveals the annealed sample includes ZnO nanobamboos and nanowires. High resolution TEM image and electron diffraction pattern confirm that the structure of ZnO nanobamboo is regular stacking of Zn and O layers with high crystal quality. The growth direction is determined as along [001] direction (c axis). TEM observations confirm that the formation of bamboo-shape ZnO is due to the stacking fault and cleavage. The bundle of those stacking faults seems to be the origin of the black contrast at the nodes. The uniformity of chemical composition for the nanobamboos is identified by EDS profiles. A strong-narrow UV band centred at 390 nm and a weak-broad green band centred at 515 nm are observed at room temperature in the PL spectrum recorded from the annealed ZnO nanobamboos and nanowires.

scholarly journals Deposition of Lu-Fe-O thin films on silica glass substrates by MOCVD

2020 ◽  
Vol 233 ◽  
pp. 05006
Author(s):  
A.F. Cardoso ◽  
A.A. Bassou ◽  
V.S. Amaral ◽  
J.R. Fernandes ◽  
P.B. Tavares
Keyword(s):  
Thin Films ◽  
Silica Glass ◽  
Room Temperature ◽  
Annealing Temperature ◽  
Magnetic Measurements ◽  
Garnet Phase ◽  
Glass Substrates ◽  
Post Annealing ◽  
Post Annealing Temperature ◽  
Deposition Conditions

Thin films of the Lu-Fe-O system were deposited by aerosol assisted MOCVD on silica glass substrates. Hexagonal h-LuFeO3, garnet Lu3Fe5O12, perovskite o-LuFeO3 or hematite Fe2O3 phases were obtained, depending on the thermodynamic deposition conditions or post annealing temperature. Magnetic measurements confirm the ferromagnetic behaviour at room temperature of the thin films with garnet phase. An indirect bandgap of 1.78 eV was measured.

Effect of Doping Concentration on Grain Boundary Conductivity of Samaria Doped Ceria Composites

2021 ◽  
Author(s):  
Prerna Vinchhi ◽  
Roma Patel ◽  
Indrajit Mukhopadhyay ◽  
Abhijit Ray ◽  
Ranjan Pati
Keyword(s):  
Ionic Conductivity ◽  
Grain Boundary ◽  
Doping Concentration ◽  
Single Phase ◽  
Precipitation Method ◽  
Molecular Water ◽  
Doped Ceria ◽  
Boundary Conductivity ◽  
Co Precipitation ◽  
Hydrated Oxide

Abstract This work aims to study the effect of Sm3+ doping concentration on the grain boundary ionic conductivity of ceria. The materials were prepared by a modified co-precipitation method, where molecular water associated with the precursor has been utilized to facilitate the hydroxylation process. The synthesized hydroxide / hydrated oxide materials were calcined and the green body (pellet) has been sintered at high temperature in order to achieve highly dense (~ 96 %) pellet. The structural analyses were done using XRD and Raman spectroscopy, which confirm the single phase cubic structure of samaria doped ceria (SDC) nanoparticles and the surface morphology of sintered samples was studied using FESEM. The ionic conductivity was measured by AC impedance spectroscopy of the sintered pellets in the temperature range of 400-700 °C, which shows superior grain boundary conductivity. The grain boundary ionic conductivity of around 0.111 S/cm has been obtained for 15SDC composition at 600 °C.

Sign in / Sign up

Export Citation Format

Share Document