scholarly journals Process of Modeling and Optimizing the Osmotic Dehydration Pre-treatment of Okra Drying

2018 ◽  
Vol 10 (4) ◽  
pp. 493-497
Author(s):  
Adesoji Matthew OLANIYAN ◽  
Bamidele David OMOLEYOMI ◽  
Musliu Olushola SUNMONU

Okra [Abelmoschuscaillei (A. Chev.) Stevels] drying was studied by a factorial experiment under randomized complete block design using a laboratory-scale hot-air dryer. Two osmotic solution concentrations (40 and 60 oBrix of sucrose), three osmotic process durations (60, 120 and 180 min) and four drying temperatures (50, 60, 70 and 80 oC) were considered with each trial conducted in triplicates. Drying rate was determined as the ratio of change in mass of okra to the change in drying time as drying progresses. The ash content, crude fibre, crude fat, crude protein, bulk density, least gelation concentration and water absorption capacity were investigated as quality parameters. Model equations were developed using Essential Regression (ESSREG) analysis and Statistical Package for Social Sciences (SPSS) to relate output parameters to process variables. The results showed that an optimum drying rate of 16.69 g/h could be achieved by subjecting okra to osmotic dehydration pretreatment using a solution of 40 oBrix sucrose for 149.10 min and dried with a temperature of 80 oC. The ash content of 3.76% could be obtained at 40 oBrix, 180 min and 50 oC. An optimum value of 29.65% was obtained for crude fibre at an osmotic solution concentration of 60 °Brix, osmotic process duration of 180 min and drying temperature of 80 oC. Crude fat content of okra has 4.03% as its optimum value and this corresponds to a combination of 60 oBrix osmotic solution concentration, 180 min osmotic process duration and 74.60 oC drying temperature. An osmotic solution concentration of 60 °Brix, osmotic process duration of 60 min and drying temperature of 80 oC should be selected to give the optimum crude protein of 14.12%. Predicted values of drying rate, ash content, crude fibre, crude fat, crude protein and water absorption capacity (WAC) compared favourably with the observed values. This implies the models reliably predicted the drying characteristics of okra very well in terms of these output parameters. It could be inferred from this study that the drying process of okra can be optimized under different drying conditions. Further studies should be carried out on the factors that affect the storability of dried okra for long-time storage and preservation. An investigation into the use of sodium chloride for osmotic dehydration pretreatment as a means of improving the post-drying palatability of okra should be considered for further study.

2021 ◽  
Vol 8 (3) ◽  
pp. 032-037
Author(s):  
Christiana Alami Adamade ◽  
Joshua Olanrewaju Olaoye

A study on modeling and optimization of foam mat drying of ripe mango was carried out, three levels of whipping durations (5 min, 10 min and 15 min, three levels of Egg white albumen powder concentrations as foaming agent (6% (w/w), 12%(w/w) and 18% (w/w)), three levels of Xanthan gum concentration as foam stabilizing agent (0.02%, 0.04% and 0.06%)and three levels of air drying temperature (50°C, 60°C and 70 °C) as input parameters were used. Design Expert 6.06 version was used to design the experiment in order to get all possible combinations of durations and concentrations. After washing and deseeding all samples of fresh mango, the pulp was foamed using egg white powder and liquid as foaming agent, the was stabilized by using xantham gum at different concentrations. The foamed products were all dried at 50°C, 60°C and 70 °C respectively in an instrumented cabinet dryer. The following output parameters were modeled and optimized with Design Expert 6.0.6 version: drying rate, vitamin C, beta carotene, crude protein, crude fibre, fat content, ash content, moisture content, carbohydrate and total soluble sugar. Ten (10) model equations, one for each of the output parameters were developed, and checked for adequacy and validity. All developed model equations were found to present functional relationships between input and output parameters. Hence, all developed model equations can be used as reliable tools for estimating, predicting and conducting analysis of the process. Best optimized results were selected base on the one that is most desirable. One of the ways of explaining optimization is that, it is the process of getting the values of input parameters that will either maximize or minimize the output parameters, drying rate (maximized), vitamin C (maximized), beta carotene (maximized), crude protein (maximized), crude fibre (maximized), fat (maximized), ash content (maximized), moisture content (minimized), carbohydrate (maximized), total soluble sugar (maximized) and moisture ratio (minimized).


2019 ◽  
Vol 15 (3) ◽  
pp. 228-233
Author(s):  
Prabhavathi Supriya ◽  
Kandikere R. Sridhar

Background: Utilization of wild legumes has received prime importance in the recent past to compensate the scarcity of protein-rich foods as well as to tackle the protein energy malnutrition. Ripened split beans of Canavalia maritima devoid of seed coat and testa serve as traditional nutraceutical source for the coastal dwellers of Southwest India. Objective: The present study projects proximal and functional attributes of uncooked and cooked ripened split beans of C. maritima to be used in the preparation of functional foods. Methods: Proximal properties (moisture, crude protein, total lipids, crude fibre, carbohydrates and calorific value) and functional properties (protein solubility, gelation capacity, water-absorption, oilabsorption, emulsion qualities and foam qualities) of split beans were evaluated by standard methods. Results: Cooking did not significantly changed the crude protein, total lipids, ash, carbohydrates and calorific value, while it significantly increased the crude fibre. The protein solubility, water-absorption capacity, foam capacity and foam stability were significantly higher in uncooked than cooked beans. The cooked beans were superior to uncooked beans in least gelation concentration, low oil-absorption capacity, emulsion activity and emulsion stability. Conclusion: The functional properties of split bean flours were influenced by the proximal components like crude protein, total lipids and crude fibre. The energy-rich ripened split beans of C. maritima can serve as a new potential source for production of value added functional foods owing to their rich protein, rich carbohydrates, low-lipid and potential bioactive attributes.


2016 ◽  
Vol 5 (1) ◽  
pp. 6 ◽  
Author(s):  
Chinyere Ilodibia ◽  
Ngozi Igboabuchi

Phytochemical and nutritional potentials of various parts (leaf, stem and root) of Talinum triangulare were evaluated using standard techniques. Analysis of Variance (ANOVA) was employed in data analysis. All the parts of the species were found to contain nutrient compositions in varying levels. Dry matter and carbohydrate were highest in the stem (91.69±0.12 and 68.66±0.01) respectively. Moisture, ash content and crude fibre were highest in the root (9.78±0.04, 17.53±0.11and 15.32±0.03) respectively while ether extract and crude protein were highest in the leaf (1.09±0.01 and 17.72±0.17) respectively. The results showed also varying quantities of the phytochemicals in the leaf, stem and root with some parts lacking some of the phytochemicals. The leaf contained the highest percentage of all the phytochemical investigated alkaloid, flavonoid, tannin, sterol, Terpenoid, phenol and saponin (0.47±0.01, 0.26±0.00, 0.36±0.07, 0.03±0.01, 0.42±0.02, 0.02±0.01and 0.68±0.05 respectively. The root lacked sterol and phenol while stem lacked only phenol. The leaf, stem and root lacked cyanogenic glycoside. The results have indicated that these parts of the Talinum triangulare investigated are very nutritious and possessed bioactive compounds that could be extracted for the manufacture of new drug, food supplements and also be used in ethnomedicine for the treatment of diseases.


Author(s):  
Samson A. Adeleye ◽  
Iyiola O. Oluwaleye ◽  
Taiwo O. Oni

Aim: This work gives the reports on experimental study of the effects of drying on some selected vegetables, namely fluted pumpkin (specimen I), spinach (specimen II), lettuce (specimen III), and waterleaf (specimen IV). Methodology: The vegetable specimens were dried at regulated drying temperatures of 323K, 333K, and 343K, and the percentage amount of water, fat, crude fibre, ash, protein, and carbohydrate, as well as the fungi and bacteria counts in the vegetable specimens was determined at these temperatures. Results: The results revealed that the amount of water in the vegetable specimens reached 0% earlier at the regulated drying temperature of 343K than at the other regulated drying temperatures. The results also indicated that the dried vegetable specimen II has highest fat content of 8.2%, the dried vegetable specimen III has highest crude fibre content of 14.5%, the dried vegetable specimen IV has highest ash content of 18.6%, the dried vegetable specimen I has highest protein content of 30.3%, and the dried vegetable s specimen III has highest carbohydrate content of 42.2% at the regulated drying temperature of 323K. The same trend of results was obtained for the regulated drying temperatures of 333K and 343K. Furthermore, the results showed that at the regulated drying temperature of 323K, the dried vegetable specimen III has the lowest bacteria counts of 4.3 x 107 CFU/g. The trend of result obtained for the regulated drying temperatures of 333K and 343K is similar to that of the 323K. At the regulated drying temperature of 323K, the dried vegetable specimen II has the lowest bacteria counts of 1.7 x 107 CFU/g. The same trend of results was obtained for the regulated drying temperatures of 333K and 343K. Conclusions: Drying has effects on the percentage amount of fat, crude fibre, ash, protein, and carbohydrate in the vegetable specimens. The microbial counts and the fungi counts decrease when the temperature increases. The present work can be applied in food engineering industries, and engineering in agriculture.


2020 ◽  
pp. 21-30
Author(s):  
Animesh Sarkar ◽  
Tushar Ahmed ◽  
Mahabub Alam ◽  
Somirita Rahman ◽  
Shishir Kanti Pramanik

This research was conducted to assess the drying kinetics and product quality during osmotic dehydration and air drying of coconut cuts. The coconuts were osmotically pretreated by different concentration of sugar solution (40 °Brix, 50 °Brix, and 60 °Brix) and temperature of osmotic solution (35°C, 45°C and 55°C) were maintained. The proportion of fruit to solution was maintained 1:4 (w/v) and pretreatment process length was 3 hours. Higher osmotic solution temperature at 55°C with low concentration 40 °Brix resulted in a huge reduction of antioxidant activity, vitamin C, polyphenol, and color contents while higher osmotic solution concentration at 50 °Brix with lower temperature 35°C held more. The present investigation likewise exhibited that moisture loss and solute gain rate extended with the increasing of osmotic solution temperature and concentration. The outcomes demonstrated that drying regime was typically in the falling rate period. We used regression analysis to the experimental drying data to fit three thin layer drying models. The most appropriate model(s) was selected using correlation coefficient (R2) and root mean square error (RMSE). The page model showed a better fit of the experimental drying data (as compared to other models) on the basis that R2> 0.9997 and RMSE < 0.0011. These data represent a good contribution to further investigation on the mass transfer kinetics and also demonstrated that fruits could be preserved with higher nutrient applying osmotic dehydration technique.


Author(s):  
M. O. Sunmonu ◽  
E. O. Ajala ◽  
M. M. Odewole ◽  
S. Morrison ◽  
A. M. Alabi

This study investigates physical and chemical properties two seeds namely Ugba (Telfairia pedata) and Ugwu (Telfairia occidentalis) using soaking soxhlet methods of extraction. The physical properties examined are moisture content, ash content, crude protein, fat and oil, crude fibre and carbohydrates. The chemical properties examined are Acid value (mgKOH/g), saponification value, iodine value, free fatty acid, peroxide and refractive index. Higher mean values of moisture content, ash content, crude fibre and carbohydrates were noticed in Ugwu than in Ugba under soaking method. However, the trend was reversed for crude protein and free fatty acid, in whose case they appear to be higher in Ugba than in Ugwu. For soxhlet method, moisture content, ash content, crude fibre and carbohydrates seems to have higher mean values in Ugwu seed compared to when Ugba seed was used. However, crude protein and fat and oil content were higher using Ugba seed than Ugwu seed oil. For soaking method, Ugba seed seem to produce higher mean values of sap value, iodine value, and refractive index when compared with Ugwu seed. On the other Ugwu, seems to produce acid value, free fatty acid and peroxide value when compared with ugba for soaking method. Using soxhlet apparatus however, Ugba seed produces higher mean values for acid value, sap value, iodine value, and free fatty acid compared to Ugwu. The reverse was the case with peroxide and refractive index, still with soxhlet apparatus.Kathmandu University Journal of Science, Engineering and TechnologyVol. 13, No. 2, 2017, page: 48-60


2012 ◽  
Vol 554-556 ◽  
pp. 1466-1469
Author(s):  
Sirasa Jengsooksawat ◽  
Sawanit Aichayawanich

This research aimed to study on the optimum condition for osmotic dehydration of pomelo. The experimental procedure was divided into 2 sections. For first section, the effect of sucrose solution concentration (50, 60, and 70 oBrix) on osmotic rate and moisture content of osmotic dehydrated pomelo were evaluated. After that, the effects of drying temperature (50, 65, and 80oC) on quality of osmotic dehydrated pomelo including, odor, texture, taste, and color were determined. The experimental results showed that the osmotic dehydration rate of pomelo were 6.4, 9.4, and 9.6 oBrix/hr when the pomelo was immersed in 50, 60, and 70 oBrix sucrose solutions, respectively. The moisture content of osmotic dehydrated pomelo which immersed in 70oBrix was lowest. The osmotic dehydrated pomelo that was immersed in 70 oBrix sucrose solutions and dried at 50oC has highest quality.


1991 ◽  
Vol 27 (1) ◽  
pp. 33-37 ◽  
Author(s):  
G. O. Iremiren ◽  
A. W. Osara ◽  
D. A. Okiy

SUMMARYDifferences in the age at which okra pods were harvested (4, 7, 10 or 13 days after pod set) had no effect on vegetative growth or pod yield, but pods harvested more than seven days after pod set were of poorer quality. The reduction in pod quality arose mainly from an increase in crude fibre and a reduction in the moisture, crude protein and ash content of older pods.


Author(s):  
S. O. Oyibo ◽  
G. C. Akani ◽  
C. C. Amuzie

This paper investigated the proximate, minerals and serum biochemistry in Hoplobatrachus occipitalis. The proximate and selected minerals of edible frog Hoplobatrachus occipitalis were determined using standard analytical methods. The result showed that crude protein was 16.91% carbohydrate was 1.76%, crude fibre 2.85%, The fat was 4.96% ash content was 1.84% and moisture was 71.67%. The selected mineral constituent recorded showed that sodium> iron> calcium > potassium > manganese. The nutritive serum biochemistry was determined in male and female species, the results revealed that both sexes have high nutritional profile suitable for human consumption; nevertheless, the female species have higher nutritional values than the males.


Author(s):  
Florence A. Bello ◽  
Nkpoikana A. Akpaoko ◽  
Victor E. Ntukidem

Nutritive, less bulk and low cost complementary flour blends were produced from maize, carrot and pigeon pea. Five different blends of flour were formulated from maize, carrot and pigeon pea in the ratio of 100:0:0 (A), 90:5:5 (B), 85:5:10 (C), 80:5:15 (D) and 75:5:20 (E) while commercial formula (sample F) served as control. The formulated complementary flour blends were analyzed for their functional properties, proximate, selected mineral and vitamin compositions while the reconstituted samples (gruel) were evaluated for sensory attributes. The functional properties of the complementary flour blends showed less bulk density (0.72-0.76 g/ml) below the commercial formula (1.26 g/ml), low water and oil absorption capacity as well as swelling index. The proximate composition showed significant (p<0.05) increase and ranged from 4.08-4.91% moisture, 6.15-9.48% crude protein, 1.33-1.48% ash, 1.98-2.71% crude fibre, 3.07-4.15% lipid, and 82.93-86.72% carbohydrate. Vitamins A and C were also increased significantly as the levels of substitution increased from 1.80-2.14 µ/100g and 3.21-4.42 µ/100g, respectively. The sensory scores showed that sample A was most preferred followed by sample B in terms of general acceptability.


Sign in / Sign up

Export Citation Format

Share Document