scholarly journals Incorporating electrokinetic effects in the porochemoelastic inclined wellbore formulation and solution

2010 ◽  
Vol 82 (1) ◽  
pp. 195-222 ◽  
Author(s):  
Vinh X. Nguyen ◽  
Youname N. Abousleiman
Keyword(s):  
Pore Pressure ◽  
Chemical Potential ◽  
Electrical Potential ◽  
Three Dimensional ◽  
Biological Tissues ◽  
Exchange Capacity ◽  
Analytical Models ◽  
Pressure Distributions ◽  
Pressure Chemical ◽  
Benchmark Solutions

The porochemoelectroelastic analytical models and solutions have been used to describe the response of chemically active and electrically charged saturated porous media such as clays, shales, and biological tissues. However, these attempts have been restricted to one-dimensional consolidation problems, which are very limited in practice and not general enough to serve as benchmark solutions for numerical validation. This work summarizes the general linear porochemoelectroelastic formulation and presents the solution of an inclined wellbore drilled in a fluid-saturated chemically active and ionized formation, such as shale, and subjected to a three-dimensional in-situ state of stress. The analytical solution to this geometry incorporates the coupled solid deformation and simultaneous fluid/ion flows induced by the combined influences of pore pressure, chemical potential, and electrical potential gradients under isothermal conditions. The formation pore fluid is modeled as an electrolyte solution comprised of a solvent and one type of dissolved cation and anion. The analytical approach also integrates into the solution the quantitative use of the cation exchange capacity (CEC) commonly obtained from laboratory measurements on shale samples. The results for stresses and pore pressure distributions due to the coupled electrochemical effects are illustrated and plotted in the vicinity of the inclined wellbore and compared with the classical porochemoelastic and poroelastic solutions.

The Effects of Anisotropic Transport Coefficients on Pore Pressure in Shale Formations

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
Vahid Dokhani ◽  
Mengjiao Yu ◽  
Stefan Z. Miska ◽  
James Bloys
Keyword(s):  
Pore Pressure ◽  
Fluid Transport ◽  
Drilling Fluid ◽  
Transport Coefficients ◽  
Electrical Potential ◽  
Three Dimensional ◽  
Bedding Plane ◽  
Wellbore Stability ◽  
Coupled Flow ◽  
In Situ Conditions

This study investigates shale–fluid interactions through experimental approaches under simulated in situ conditions to determine the effects of bedding plane orientation on fluid flow through shale. Current wellbore stability models are developed based on isotropic conditions, where fluid transport coefficients are only considered in the radial direction. This paper also presents a novel mathematical method, which takes into account the three-dimensional coupled flow of water and solutes due to hydraulic, chemical, and electrical potential imposed by the drilling fluid and/or the shale formation. Numerical results indicate that the presence of microfissures can change the pore pressure distribution significantly around the wellbore and thus directly affect the mechanical strength of the shale.

Modeling Time-Dependent Pore Pressure Due to Capillary and Chemical Potential Effects and Resulting Wellbore Stability in Shales

2003 ◽  
Vol 125 (3) ◽  
pp. 169-176 ◽  
Author(s):  
M. K. Rahman ◽  
Zhixi Chen ◽  
Sheik S. Rahman
Keyword(s):  
Pore Pressure ◽  
Chemical Potential ◽  
Normal Fault ◽  
Wellbore Stability ◽  
Time Dependent ◽  
Analytical Models ◽  
Analysis Model ◽  
Stress Regime ◽  
Dependent Change ◽  
Drilling Operations

During drilling operations, the mud filtrate interacts with the pore fluid around the wellbore and changes pore pressure by capillary and chemical potential effects. Thus the change in pore pressure around borehole becomes time-dependent, particularly in extremely low permeability shaley formations. In this paper, the change in pore pressure due to capillary and chemical potential effects are investigated experimentally. Analytical models are also developed based on the experimental results. A wellbore stability analysis model incorporating the time-dependent change in pore pressure is applied to a vertical well in a shale formation under normal fault stress regime.

Three-Dimensional Visualization of the T-System of Frog Muscle Using High Voltage Electron Microscopy and a Lanthanum Stain

1977 ◽  
Vol 35 ◽  
pp. 570-571 ◽  
Author(s):  
Lee D. Peachey ◽  
Clara Franzini-Armstrong
Keyword(s):  
Electron Microscopy ◽  
High Voltage ◽  
Three Dimensional ◽  
Biological Tissues ◽  
High Voltage Electron Microscopy ◽  
Transverse Tubular System ◽  
Peroxidase Reaction ◽  
Voltage Electron ◽  
High Voltage Electron ◽  
T System

The effective study of biological tissues in thick slices of embedded material by high voltage electron microscopy (HVEM) requires highly selective staining of those structures to be visualized so that they are not hidden or obscured by other structures in the image. A tilt pair of micrographs with subsequent stereoscopic viewing can be an important aid in three-dimensional visualization of these images, once an appropriate stain has been found. The peroxidase reaction has been used for this purpose in visualizing the T-system (transverse tubular system) of frog skeletal muscle by HVEM (1). We have found infiltration with lanthanum hydroxide to be particularly useful for three-dimensional visualization of certain aspects of the structure of the T- system in skeletal muscles of the frog. Specifically, lanthanum more completely fills the lumen of the tubules and is denser than the peroxidase reaction product.

Validation of a Belt Model for Prediction of Hub Forces from a Rolling Tire4

2009 ◽  
Vol 37 (2) ◽  
pp. 62-102 ◽  
Author(s):  
C. Lecomte ◽  
W. R. Graham ◽  
D. J. O’Boy
Keyword(s):  
Internal Pressure ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Prediction Method ◽  
Analytical Models ◽  
Beam Model ◽  
Impedance Boundary ◽  
Bending Waves ◽  
Tire Rotation ◽  
Three Dimensional Models

Abstract An integrated model is under development which will be able to predict the interior noise due to the vibrations of a rolling tire structurally transmitted to the hub of a vehicle. Here, the tire belt model used as part of this prediction method is first briefly presented and discussed, and it is then compared to other models available in the literature. This component will be linked to the tread blocks through normal and tangential forces and to the sidewalls through impedance boundary conditions. The tire belt is modeled as an orthotropic cylindrical ring of negligible thickness with rotational effects, internal pressure, and prestresses included. The associated equations of motion are derived by a variational approach and are investigated for both unforced and forced motions. The model supports extensional and bending waves, which are believed to be the important features to correctly predict the hub forces in the midfrequency (50–500 Hz) range of interest. The predicted waves and forced responses of a benchmark structure are compared to the predictions of several alternative analytical models: two three dimensional models that can support multiple isotropic layers, one of these models include curvature and the other one is flat; a one-dimensional beam model which does not consider axial variations; and several shell models. Finally, the effects of internal pressure, prestress, curvature, and tire rotation on free waves are discussed.

scholarly journals Numerical simulation of the impact of an integrated renovation project on the Maowei Sea hydrodynamic environment

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Cui Wang ◽  
Ling Cai ◽  
Yaojian Wu ◽  
Yurong Ouyang
Keyword(s):  
Water Exchange ◽  
Land Reclamation ◽  
Three Dimensional ◽  
Exchange Capacity ◽  
Reclamation Project ◽  
Hydrodynamic Environment ◽  
Sea Area ◽  
Water Quality Models ◽  
The Impact ◽  
Main Factor

AbstractIntegrated renovation projects are important for marine ecological environment protection. Three-dimensional hydrodynamics and water quality models are developed for the Maowei Sea to assess the hydrodynamic environment base on the MIKE3 software with high resolution meshes. The results showed that the flow velocity changed minimally after the project, decreasing by approximately 0.12 m/s in the east of the Maowei Sea area and increasing by approximately 0.01 m/s in the northeast of the Shajing Port. The decrease in tidal prism (~ 2.66 × 106 m3) was attributed to land reclamation, and accounted for just 0.86% of the pre-project level. The water exchange half-life increased by approximately 1 day, implying a slightly reduced water exchange capacity. Siltation occurred mainly in the reclamation and dredging areas, amounting to back-silting of approximately 2 cm/year. Reclamation project is the main factor causing the decrease of tidal volume and weakening the hydrodynamics in Maowei Sea. Adaptive management is necessary for such a comprehensive regulation project. According to the result, we suggest that reclamation works should strictly prohibit and dredging schemes should optimize in the subsequent regulation works.

scholarly journals A computational framework for modeling cell–matrix interactions in soft biological tissues

2021 ◽  
Author(s):  
Jonas F. Eichinger ◽  
Maximilian J. Grill ◽  
Iman Davoodi Kermani ◽  
Roland C. Aydin ◽  
Wolfgang A. Wall ◽  
...  
Keyword(s):  
Soft Tissues ◽  
Three Dimensional ◽  
Biological Tissues ◽  
Computational Framework ◽  
Cell Matrix ◽  
Physiological Processes ◽  
Matrix Interactions ◽  
Mechanical Homeostasis ◽  
Cell Matrix Interactions ◽  
Short Time

AbstractLiving soft tissues appear to promote the development and maintenance of a preferred mechanical state within a defined tolerance around a so-called set point. This phenomenon is often referred to as mechanical homeostasis. In contradiction to the prominent role of mechanical homeostasis in various (patho)physiological processes, its underlying micromechanical mechanisms acting on the level of individual cells and fibers remain poorly understood, especially how these mechanisms on the microscale lead to what we macroscopically call mechanical homeostasis. Here, we present a novel computational framework based on the finite element method that is constructed bottom up, that is, it models key mechanobiological mechanisms such as actin cytoskeleton contraction and molecular clutch behavior of individual cells interacting with a reconstructed three-dimensional extracellular fiber matrix. The framework reproduces many experimental observations regarding mechanical homeostasis on short time scales (hours), in which the deposition and degradation of extracellular matrix can largely be neglected. This model can serve as a systematic tool for future in silico studies of the origin of the numerous still unexplained experimental observations about mechanical homeostasis.

Laminar Fluid Flow Around Two Wall-Mounted Blocks of Different Size

2009 ◽  
Author(s):  
Mohammad Mehdi Tavakol ◽  
Mohammad Eslami
Keyword(s):  
Fluid Flow ◽  
Free Stream ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Bluff Bodies ◽  
Wake Region ◽  
Science And Engineering ◽  
Vortical Structures ◽  
Laminar Fluid Flow ◽  
Pressure Distributions

Fluid flow around single or multiple bluff bodies mounted on a surface has great significance in science and engineering. Understanding the characteristics of different vortices formed around wall-mounted bodies is quite necessary for different applications. Although the case of a single surface mounted cube has been studied extensively, only little attention has been paid to the flow around two or more rectangular blocks in array. Therefore, a CFD code is developed to calculate three dimensional steady state laminar fluid flow around two cuboids of arbitrary size and configuration mounted on a surface in free stream conditions. The employed numerical scheme is finite volume and SIMPLE algorithm is used to treat pressure and velocity coupling. Results are presented for two rectangular blocks of the different size mounted on a surface in various inline arrangements. Streamlines are plotted for blocks of different size ratio. Velocity and pressure distributions are also plotted in the wake region behind the obstacles. It is shown that how the behavior of flow field and vortical structures depend on the respective size and location of the larger block in comparison with the case of two inline wall mounted cubes of the same size.

Research on Three-Dimensional Displacement Measurement Technology of the Beating Heart

2011 ◽  
Vol 403-408 ◽  
pp. 5182-5186
Author(s):  
Sheng Yi Yang ◽  
An Gu ◽  
Meng Li ◽  
Chang Jian Lu
Keyword(s):  
Heart Surgery ◽  
Classical Mechanics ◽  
Three Dimensional ◽  
Beating Heart ◽  
Displacement Measurement ◽  
Surgical Instruments ◽  
Analytical Models ◽  
Measurement Technology ◽  
Position Measurement ◽  
Mechanics Of Materials

In robotic-assisted heart surgery, the method of canceling the relative motion between the surgical site on the heart and the surgical instruments was introduced in this paper. A whisker sensor was designed for three dimensional position measurement in beating heart surgery. Analytical models were developed according to the classical mechanics of materials, and theoretical formulas were derived for displacement measurement. Feasibility and effectiveness of the method were verified by simulation experiments. We can obtain measurements by loading displacement to the whisker sensor, and draw conclusions by comparing the measurements.

scholarly journals High-resolution three-dimensional probes of biomaterials and their interfaces

2012 ◽  
Vol 370 (1963) ◽  
pp. 1337-1351 ◽  
Author(s):  
Kathryn Grandfield ◽  
Anders Palmquist ◽  
Håkan Engqvist
Keyword(s):  
High Resolution ◽  
Electron Tomography ◽  
Three Dimensional ◽  
Controlled Drug Release ◽  
Biological Tissues ◽  
Dimensional Structure ◽  
Bone Interface ◽  
Biomaterial Interfaces ◽  
Titania Coating

Interfacial relationships between biomaterials and tissues strongly influence the success of implant materials and their long-term functionality. Owing to the inhomogeneity of biological tissues at an interface, in particular bone tissue, two-dimensional images often lack detail on the interfacial morphological complexity. Furthermore, the increasing use of nanotechnology in the design and production of biomaterials demands characterization techniques on a similar length scale. Electron tomography (ET) can meet these challenges by enabling high-resolution three-dimensional imaging of biomaterial interfaces. In this article, we review the fundamentals of ET and highlight its recent applications in probing the three-dimensional structure of bioceramics and their interfaces, with particular focus on the hydroxyapatite–bone interface, titanium dioxide–bone interface and a mesoporous titania coating for controlled drug release.

Sign in / Sign up

Export Citation Format

Share Document