scholarly journals A Low-Noise Amplifier Utilizing Current-Reuse Technique and Active Shunt Feedback for MedRadio Band Applications

2020 ◽  
pp. 306-316
Author(s):  
Mutanizam Abdul Mubin ◽  
◽  
Arjuna Marzuki
Keyword(s):  
Low Power ◽  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Common Source ◽  
Cmos Process ◽  
Current Reuse ◽  
Noise Amplifier

In this work, a low-power 0.18-μm CMOS low-noise amplifier (LNA) for MedRadio applications has been designed and verified. Cadence IC5 software with Silterra’s C18G CMOS Process Design Kit were used for all design and simulation work. This LNA utilizes complementary common-source current-reuse topology and subthreshold biasing to achieve low-power operation with simultaneous high gain and low noise figure. An active shunt feedback circuit is used as input matching network to provide a suitable input return loss. For test and measurement purpose, an output buffer was designed and integrated with this LNA. Inductorless design approach of this LNA, together with the use of MOSCAPs as capacitors, help to minimize the die size. On post-layout simulations with LNA die area of 0.06 mm2 and simulated total DC power consumption of 0.5 mW, all targeted specifications are met. The simulated gain, input return loss and noise figure of this LNA are 16.3 dB, 10.1 dB and 4.9 dB respectively throughout the MedRadio frequency range. For linearity, the simulated input-referred P1dB of this LNA is -26.7 dBm while its simulated IIP3 is -18.6 dBm. Overall, the post-layout simulated performance of this proposed LNA is fairly comparable to some current state-of-the-art LNAs for MedRadio applications. The small die area of this proposed LNA is a significant improvement in comparison to those of the previously reported MedRadio LNAs.

scholarly journals Design and Analysis High Gain PHEMT LNA for Wireless Application at 5.8 GHz

2015 ◽  
Vol 5 (3) ◽  
pp. 611
Author(s):  
Kamil Pongot ◽  
Abdul Rani Othman ◽  
Zahriladha Zakaria ◽  
Mohamad Kadim Suaidi ◽  
Abdul Hamid Hamidon ◽  
...  
Keyword(s):  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Output Terminal ◽  
Wireless Application ◽  
Noise Amplifier ◽  
The Stability ◽  
Inductive Generation

This research present a design of a higher  gain (66.38dB) for PHEMT LNA  using an inductive drain feedback technique for wireless application at 5.8GHz. The amplifier it is implemented using PHEMT FHX76LP transistor devices.  The designed circuit is simulated with  Ansoft Designer SV.  The LNA was designed using  T-network as a matching technique was used at the input and output terminal,  inductive generation to the source and an inductive drain feedback. The  low noise amplifier (LNA) using lumped-component provides a noise figure 0.64 dB and a gain (S<sub>21</sub>) of 68.94 dB. The output reflection (S<sub>22</sub>), input reflection (S<sub>11</sub>) and return loss (S<sub>12</sub>) are -17.37 dB, -15.77 dB and -88.39 dB respectively. The measurement shows the  stability was at  4.54 and 3-dB bandwidth of 1.72 GHz. While, the  low noise amplifier (LNA) using  Murata manufactured component provides a noise figure 0.60 dB and a gain (S<sub>21</sub>) of 66.38 dB. The output reflection (S<sub>22</sub>), input reflection (S<sub>11</sub>) and return loss (S<sub>12</sub>) are -13.88 dB, -12.41 dB and -89.90 dB respectively. The measurement shows the  stability was at  6.81 and 3-dB bandwidth of 1.70 GHz. The input sensitivity more than -80 dBm  exceeded the standards required by IEEE 802.16.

Optimized Design of Low Power Complementary Metal Oxide Semiconductor Low Noise Amplifier for Zigbee Application

2021 ◽  
Vol 18 (4) ◽  
pp. 1327-1330
Author(s):  
S. Manjula ◽  
R. Karthikeyan ◽  
S. Karthick ◽  
N. Logesh ◽  
M. Logeshkumar
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Supply Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Oxide Semiconductor ◽  
Design System ◽  
Cmos Process ◽  
Design Specifications ◽  
Noise Amplifier

An optimized high gain low power low noise amplifier (LNA) is presented using 90 nm CMOS process at 2.4 GHz frequency for Zigbee applications. For achieving desired design specifications, the LNA is optimized by particle swarm optimization (PSO). The PSO is successfully implemented for optimizing noise figure (NF) when satisfying all the design specifications such as gain, power dissipation, linearity and stability. PSO algorithm is developed in MATLAB to optimize the LNA parameters. The LNA with optimized parameters is simulated using Advanced Design System (ADS) Simulator. The LNA with optimized parameters produces 21.470 dB of voltage gain, 1.031 dB of noise figure at 1.02 mW power consumption with 1.2 V supply voltage. The comparison of designed LNA with and without PSO proves that the optimization improves the LNA results while satisfying all the design constraints.

A Fully Integrated 5.2-GHz CMOS Variable Gain LNA for 802.11a WLAN

2012 ◽  
Vol 433-440 ◽  
pp. 5579-5583
Author(s):  
Ji Hai Duan ◽  
Chun Lei Kang
Keyword(s):  
Power Supply ◽  
Return Loss ◽  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Small Signal ◽  
Fully Integrated ◽  
Variable Gain ◽  
Noise Amplifier

A fully integrated 5.2GHz variable gain low noise amplifier (VGLNA) in a 0.18μm CMOS process is proposed in this paper. The VGLAN can achieve a maximum small signal gain of 17.85 dB within the noise figure (NF) of 2.04 dB and a minimum gain of 2.04 dB with good input return loss. The LNA’s P1dB in the high gain mode is -17.5 dBm. The LAN consumes only 14.58 mW from a 1.8V power supply.

STUDY OF PARASITIC CAPACITANCE EFFECT ON NOISE FIGURE OF IDCLNA IN DEEP SUBMICRON CMOS TECHNOLOGIES

2014 ◽  
Vol 23 (05) ◽  
pp. 1450058
Author(s):  
S. MANJULA ◽  
D. SELVATHI
Keyword(s):  
Noise Figure ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Current Gain ◽  
Cmos Process ◽  
Short Channel ◽  
Trade Offs ◽  
Noise Amplifier ◽  
The Impact

Low noise amplifier (LNA) is an important component in RF receiver front end. An inductively degenerated cascode low noise amplifier (IDCLNA) is mostly preferred for producing good trade-offs such as high gain, low noise figure (NF), high reverse isolation and low power consumption for narrowband applications. This IDCLNA structure is also used to reduce the gate induced noise on the noise performance by inserting the capacitance in parallel with the gate-to-source capacitance of main transistor. Usually, the parasitic overlap capacitances can impose serious constraints on achievable performance and is taken into account in IDCLNA. In this paper, IDCLNA is designed at a frequency of 2.4 GHz with analyzing the impact of parasitic overlap capacitances on IDCLNA in terms of unity current gain frequency (f T ) which will affect the NF of IDCLNA and simulated using 130 nm, 90 nm and 65 nm CMOS technologies. The NF of IDCLNA with and without parasitic overlap capacitances are analyzed and compared for different short channel CMOS processes. Simulation results show that the parasitic overlap capacitances have advantageous to reduce the gate induced noise in IDCLNA for 130-nm CMOS process for 2.4 GHz applications.

scholarly journals Analytical Performance of Low Noise Amplifier Using Single-Stage Configuration for ADS-B Receiver

2021 ◽  
Vol 21 (2) ◽  
pp. 91
Author(s):  
M. Reza Hidayat ◽  
Ilham Pazaesa ◽  
Salita Ulitia Prini
Keyword(s):  
Return Loss ◽  
Noise Figure ◽  
Impedance Matching ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Stability Factor ◽  
Ic 10 ◽  
Radar Applications ◽  
Noise Amplifier

Automatic dependent surveillance-broadcast (ADS-B) is an equipment of a radar system to reach difficult areas. For radar applications, an ADS-B requires a low noise amplifier (LNA) with high gain, stability, and a low noise figure. In this research, to produce an LNA with good performance, an LNA was designed using a BJT transistor 2SC5006 with DC bias, VCE = 3 V, and current Ic = 10 mA, also a DC supply with VCC = 12 V, to achieve a high gain with a low noise figure. The initial LNA impedance circuit was simulated using 2 elements and then converted into 3 elements to obtain parameters according to the target specification through the tuning process, impedance matching circuit was used to reduce return loss and voltage standing wave ratio (VSWR) values. The LNA sequence obtains the working frequency of 1090 MHz, return loss of -52.103 dB, a gain of 10.382, VSWR of 1.005, a noise figure of 0.552, stability factor of 0.997, and bandwidth of 83 MHz. From the simulation results, the LNA has been successfully designed according to the ADS-B receiver specifications.

scholarly journals A concurrent dual-band CMOS low noise amplifier at 2.4/5.2 GHz for WLAN applications

2019 ◽  
Vol 14 (2) ◽  
pp. 555
Author(s):  
S.A.Z. Murad ◽  
A. F. Hasan ◽  
A. Azizan ◽  
A. Harun ◽  
J. Karim
Keyword(s):  
Noise Figure ◽  
Supply Voltage ◽  
Notch Filter ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Dual Band ◽  
Common Source ◽  
Noise Amplifier

<span>This paper presents a concurrent dual-band CMOS low noise amplifier (LNA) at operating frequency of 2.4 GHz and 5.2 GHz for WLAN applications. The proposed LNA employed cascode common source to obtain high gain using 0.13-µm CMOS technology. The concurrent dual-band frequencies are matched using LC network band-pass and band-stop notch filter at the input and output stages. The filters help to shape the frequency response of the proposed LNA. The simulation results indicate that the LNA achieves a forward gain of 21.8 dB and 14.22 dB, input return loss of -18 dB and -14 dB at 2.4 GHz and 5.2 GHz, respectively. The noise figure of 4.1 dB and 3.5 dB with the input third-order intercept points 7 dBm and 10 dBm are obtained at 2.4 GHz and 5.2 GHz, respectively. The LNA dissipates 2.4 mW power at 1.2 V supply voltage with a chip size of 1.69 mm2.</span>

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

scholarly journals Design of Low Power UWB CMOS Low Noise Amplifier using Active Inductor for WLAN Receiver

2018 ◽  
Vol 7 (2.24) ◽  
pp. 448
Author(s):  
S Manjula ◽  
M Malleshwari ◽  
M Suganthy
Keyword(s):  
Low Power ◽  
Noise Figure ◽  
Wide Band ◽  
Cmos Technology ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Design System ◽  
Active Inductor ◽  
Chip Area ◽  
Noise Amplifier

This paper presents a low power Low Noise Amplifier (LNA) using 0.18µm CMOS technology for ultra wide band (UWB) applications. gm boosting common gate (CG) LNA is designed to improve the noise performance.  For the reduction of on chip area, active inductor is employed at the input side of the designed LNA for input impedance matching. The proposed UWB LNA is designed using Advanced Design System (ADS) at UWB frequency of 3.1-10.6 GHz. Simulation results show that the gain of 10.74+ 0.01 dB, noise figure is 4.855 dB, input return loss <-13 dB and 12.5 mW power consumption.  

Inductive Feedback Technique for Design of High Gain 0.18μm CMOS LNA for 5G Applications

2021 ◽  
pp. 2150236
Author(s):  
Anjana Jyothi Banu ◽  
G. Kavya ◽  
D. Jahnavi
Keyword(s):  
Reflection Coefficient ◽  
Noise Figure ◽  
Cmos Technology ◽  
High Gain ◽  
Low Noise ◽  
Common Source ◽  
Matching Network ◽  
Input Matching ◽  
Cmos Lna ◽  
Noise Amplifier

A 26[Formula: see text]GHz low-noise amplifier (LNA) designed for 5G applications using 0.18[Formula: see text][Formula: see text]m CMOS technology is proposed in this paper. The circuit includes a common-source in the first stage to suppress the noise in the amplifier. The successive stage has a Cascode topology along with an inductive feedback to improve the power gain. The input matching network is designed to achieve the input reflection coefficient less than [Formula: see text]7dB at the intended frequency. The matching network at the output is designed using inductor–capacitor (LC) components connected in parallel to attain the output reflection coefficient of [Formula: see text]10[Formula: see text]dB. Due to the inductor added in feedback at the second stage. The [Formula: see text] obtained is 18.208[Formula: see text]dB at 26[Formula: see text]GHz with a noise figure (NF) of 2.8[Formula: see text]dB. The power supply given to the LNA is 1.8[Formula: see text]V. The simulation and layout of the presented circuit are performed using Cadence Virtuoso software.

Design of Low-Noise Two-Path Amplifier for 6–16 GHz Applications

2020 ◽  
pp. 2150136
Author(s):  
Asieh Parhizkar Tarighat ◽  
Mostafa Yargholi
Keyword(s):  
Noise Figure ◽  
Impedance Matching ◽  
High Gain ◽  
Low Noise ◽  
Cmos Process ◽  
Input Matching ◽  
Inductive Peaking ◽  
Linearity Improvement ◽  
Noise Amplifier ◽  
Path Structure

A two-path low-noise amplifier (LNA) is designed with TSMC 0.18[Formula: see text][Formula: see text]m standard RF CMOS process for 6–16[Formula: see text]GHz frequency band applications. The principle of a conventional resistive shunt feedback LNA is analyzed to demonstrate the trade-off between the noise figure (NF) and the input matching. To alleviate the mentioned issue for wideband application, this structure with noise canceling technique and linearity improvement are applied to a two-path structure. Flat and high gain is supplied by the primary path; while the input and output impedance matching are provided by the secondary path. The [Formula: see text][Formula: see text]dB bandwidth can be increased to a higher frequency by inductive peaking, which is used at the first stage of the two paths. Besides, by biasing the transistors at the threshold voltage, low power dissipation is achieved. The [Formula: see text][Formula: see text]dB gain bandwidth of the proposed LNA is 10[Formula: see text]GHz, while the maximum power gain of 13.1[Formula: see text]dB is attained. With this structure, minimum NF of 4.6[Formula: see text]dB and noise flatness of 1[Formula: see text]dB in the whole bandwidth can be achieved. The input impedance is matched, and S[Formula: see text] is lower than [Formula: see text]10 dB. With the proposed linearized LNA, the average IIP[Formula: see text][Formula: see text]dBm is gained, while it occupies 1051.7[Formula: see text][Formula: see text]m die area.

Sign in / Sign up

Export Citation Format

Share Document