scholarly journals CHARACTERIZATION OF CLAY MATERIALS USED FOR POTTERY PURPOSES FROM RENDENG, MALO, BOJONEGORO

2021 ◽  
Vol 14 (1) ◽  
pp. 6-11
Author(s):  
Dyah Setyaningrum ◽  
Sujiat Sujiat ◽  
Aprilia Nur Azizah
Keyword(s):  
Physicochemical Characterization ◽  
Raw Material ◽  
Chemical Compositions ◽  
Clay Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plastic Type ◽  
Materials Used ◽  
Fluorescence Spectrometer

Clay material from Rendeng, Malo, Bojonegoro was studied by mineralogy and physicochemical characterization to evaluate its potential suitability as a raw material in pottery application. X-ray Diffraction (XRD) and Fourier Transform-Infrared (FTIR) spectrometry were used to establish the mineralogy composition. Meanwhile the physical properties were identified by particle size distribution and consistency limits. Chemical composition was carried out by X-ray Fluorescence Spectrometer (XRF).  The results of XRD characterization revealed that clay from Rendeng Village, Malo, Bojonegoro contained  kaolin, quartz, and feldspar. Physical characterization shows that clay material is a less plastic type based on Atterberg method. Based on the chemical compositions indicated that SiO2, Al2O3, CaO, and Fe2O3 were abundance oxides. Therefore, clay from Desa Rendeng was only suitable for the pottery purposes because most of its mineral compositions did not meet the quality requirements for making advanced ceramics.

scholarly journals Analisis Mineralogi dan Kimia Dolomit Kabupaten Bone Bolango, Provinsi Gorontalo

2021 ◽  
Vol 9 (2) ◽  
pp. 95-102
Author(s):  
Sufriadin Sufriadin ◽  
Purwanto Purwanto ◽  
Muhammad Rahmatul Jihad ◽  
Astina Aras ◽  
Angelia Santoso ◽  
...  
Keyword(s):  
Raw Materials ◽  
Xrd Analysis ◽  
Chemical Compositions ◽  
Content Increase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Agriculture Sector ◽  
Selective Mining ◽  
Fluorescence Spectrometer

Characterization of dolomite samples from Bone Bolango, Gorontalo Province have been performed with the objective to find out their mineralogical and chemical compositions. Observation and mineral analyses were carried out by means of microscopy and X-ray diffraction methods respectively; whereas chemical composition was determined by using X-ray fluorescence spectrometer. Result of XRD analysis shows that samples contain dolomite [CaMg(CO3)2], calcite [CaCO3] and [SiO2]. The proportion of dolomite is about 60.4% in average and its presence is as replacement of calcite in bioclast components and matrices in the rock. Dolomite crystals are characterized by mosaic texture with euhedral – subhedral in shapes. Spacially, dolomite content increase from west to the east of study area. The XRF analysis reveals that dolomite samples contain MgO ranging between 8.07 and 20.78% while CaO ranges between 30.04 and 56.13%. The SiO2 concentration ranges from 3.50 – 7.55%; whereas Al2O3 ranges from 1.07 – 1.84%. The average MgO content of dolomite about 12.89% can be categorized as calcium dolomite. Dolomite within the study area can be used directly in agriculture sector, but it less suitable as raw materials in glass, ceramic and refractory industries because the average content of MgO is less than 17%. However, it can be increased of their MgO with the application of selective mining or beneficiation process.

Quality Characterization of Iron Dust Exhaust Thermal as Alternative Ceramic Coating Raw Materials in a Brazilian Company

2014 ◽  
Vol 1077 ◽  
pp. 135-138
Author(s):  
Luiz Oliveira Veriano dalla Valentina ◽  
Marilena Valadares Folgueras ◽  
Wanessa Rejane Knop ◽  
Maria Cristina Pacheco do Nascimento ◽  
Glaucia Aparecida Prates
Keyword(s):  
Ceramic Coating ◽  
Raw Materials ◽  
Ceramic Materials ◽  
Raw Material ◽  
Silica Sand ◽  
Commercial Application ◽  
X Ray Diffraction ◽  
X Ray ◽  
Materials Used

As the raw materials used in the ceramic materials manufacturing are natural, it is important to use them as a alternative materials, thus decreasing the elements demand taken from nature. This paper aims the characterization of foundry solid powder exhaust from a brazilian company located in Joinville - SC as an alternative raw material for ceramic coating by X-ray diffraction (XRD), thermal analysis (DSC) and thermogravimetric (TG). The dust depletion is caused in the manufacturing mold sand process, when the bentonita (clay), silica sand and coal during the metal parts production are mixed in green sand production. The raw materials were characterized through X-ray diffraction (XRD), thermal (DSC) and thermogravimetric analisys (TG). The atomized powder thermogravimetric analysis curve shows three intervals associated with the mass loss and it is typical of clay commercial application.

scholarly journals New Insights into the Crystal Chemistry of Elpidite, Na2Zr[Si6O15]·3H2O and (Na1+YCax□1−X−Y)Σ=2Zr[Si6O15]·(3−X)H2O, and Ab Initio Modeling of IR Spectra

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2160
Author(s):  
Alexander Bogdanov ◽  
Ekaterina Kaneva ◽  
Roman Shendrik
Keyword(s):  
Ir Spectra ◽  
Structural Models ◽  
Chemical Characterization ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Special Group ◽  
X Ray ◽  
Influence Of Water ◽  
Radioactive Species

Elpidite belongs to a special group of microporous zirconosilicates, which are of great interest due to their capability to uptake various molecules and ions, e.g., some radioactive species, in their structural voids. The results of a combined electron probe microanalysis and single-crystal X-ray diffraction study of the crystals of elpidite from Burpala (Russia) and Khan-Bogdo (Mongolia) deposits are reported. Some differences in the chemical compositions are observed and substitution at several structural positions within the structure of the compounds are noted. Based on the obtained results, a detailed crystal–chemical characterization of the elpidites under study was carried out. Three different structure models of elpidite were simulated: Na2ZrSi6O15·3H2O (related to the structure of Russian elpidite), partly Ca-replaced Na1.5Ca0.25ZrSi6O15·2.75H2O (close to elpidite from Mongolia), and a hypothetical CaZrSi6O15·2H2O. The vibration spectra of the models were obtained and compared with the experimental one, taken from the literature. The strong influence of water molecule vibrations on the shape of IR spectra of studied structural models of elpidite is discussed in the paper.

Characterization and A Preliminary Study of TiO2 Synthesis from Lampung Iron Sand

2020 ◽  
Vol 849 ◽  
pp. 113-118
Author(s):  
Yayat Iman Supriyatna ◽  
Slamet Sumardi ◽  
Widi Astuti ◽  
Athessia N. Nainggolan ◽  
Ajeng W. Ismail ◽  
...  
Keyword(s):  
Food Packaging ◽  
Xrd Analysis ◽  
Major Elements ◽  
Raw Material ◽  
Solid Residue ◽  
X Ray Diffraction ◽  
X Ray ◽  
Leaching Solution ◽  
Ti Content

The purpose of this study is to characterize Lampung iron sand and to conduct preliminary experiments on the TiO2 synthesis which can be used for the manufacturing of functional food packaging. The iron sand from South Lampung Regency, Lampung Province that will be utilized as raw material. The experiment was initiated by sieving the iron sand on 80, 100, 150, 200 and 325 mesh sieves. Analysis using X-Ray Fluorescence (XRF) to determine the element content and X-Ray Diffraction (XRD) to observe the mineralization of the iron sand was conducted. The experiment was carried out through the stages of leaching, precipitation, and calcination. Roasting was applied firstly by putting the iron sand into the muffle furnace for 5 hours at a temperature of 700°C. Followed by leaching using HCl for 48 hours and heated at 105°C with a stirring speed of 300 rpm. The leaching solution was filtered with filtrate and solid residue as products. The solid residue was then leached using 10% H2O2 solution. The leached filtrate was heated at 105°C for 40 minutes resulting TiO2 precipitates (powder). Further, the powder was calcined and characterized. Characterization of raw material using XRF shows the major elements of Fe, Ti, Mg, Si, Al and Ca. The highest Ti content is found in mesh 200 with 9.6%, while iron content is about 80.7%. While from the XRD analysis, it shows five mineral types namely magnetite (Fe3O4), Rhodonite (Mn, Fe, Mg, Ca) SiO3, Quart (SiO2), Ilmenite (FeOTiO2) and Rutile (TiO2). The preliminary experiment showed that the Ti content in the synthesized TiO2 powder is 21.2%. The purity of TiO2 is low due to the presence of Fe metal which is dissolved during leaching, so that prior to precipitation purification is needed to remove impurities such as iron and other metals.

Preliminary Preparation and Characterization Studies of Cellulose from Merbau (Intsia bijuga)

2012 ◽  
Vol 620 ◽  
pp. 314-319
Author(s):  
Nur Amira Mamat Razali ◽  
Fauziah Abdul Aziz ◽  
Saadah Abdul Rahman
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Alkaline Treatment ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Preliminary Preparation ◽  
Characterization Studies ◽  
Scanning Electron

Hardwood is wood from angiosperm trees. The characteristic of hardwood include flowers, endosperm within seeds and the production of fruits that contain the seeds. This paper aims to discuss the preparation and characterization of cellulose obtained from hardwood. The hardwood Merbau (Intsia bijuga) was chosen as raw material in this study. Alkaline treatment and delignification methods were used for the preparation of cellulose. Acid hydrolysis was employed to produce cellulose nanocrystal (CNC). The treated and untreated samples were characterized using x-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The final product, from both trated and untreated samples were then compared.

scholarly journals Assay and physicochemical characterization of the antiparasitic albendazole

2012 ◽  
Vol 48 (2) ◽  
pp. 281-290 ◽  
Author(s):  
Noely Camila Tavares Cavalcanti ◽  
Giovana Damasceno Sousa ◽  
Maria Alice Maciel Tabosa ◽  
José Lamartine Soares Sobrinho ◽  
Leila Bastos Leal ◽  
...  
Keyword(s):  
Physicochemical Characterization ◽  
Analytical Techniques ◽  
Assay Method ◽  
Active Pharmaceutical Ingredients ◽  
X Ray Diffraction ◽  
Melting Points ◽  
X Ray ◽  
Pharmaceutical Ingredients ◽  
Complementary Techniques

The aim of this study was to characterize three batches of albendazole by pharmacopeial and complementary analytical techniques in order to establish more detailed specifications for the development of pharmaceutical forms. The ABZ01, ABZ02, and ABZ03 batches had melting points of 208 ºC, 208 ºC, and 209 ºC, respectively. X-ray diffraction revealed that all three batches showed crystalline behavior and the absence of polymorphism. Scanning electron microscopy showed that all the samples were crystals of different sizes with a strong tendency to aggregate. The samples were insoluble in water (5.07, 4.27, and 4.52 mg mL-1, respectively) and very slightly soluble in 0.1 M HCl (55.10, 56.90, and 61.70 mg mL-1, respectively) and additionally showed purities within the range specified by the Brazilian Pharmacopoeia 5th edition (F. Bras. V; 98% to 102%). The pharmacopeial assay method was not reproducible and some changes were necessary. The method was validated and showed to be selective, specific, linear, robust, precise, and accurate. From this characterization, we concluded that pharmacopeial techniques alone are not able to detect subtle differences in active pharmaceutical ingredients; therefore, the use of other complementary techniques is required to ensure strict quality control in the pharmaceutical industry.

scholarly journals Making and Characterization of Limnpo4 Using Solid State Reaction Method for Lithium Ion Battery Cathodes

2019 ◽  
pp. 583-588
Author(s):  
Adelyna Oktavia ◽  
Kurnia Sembiring ◽  
Slamet Priyono
Keyword(s):  
Solid State ◽  
Lithium Ion Battery ◽  
Lithium Ion ◽  
Solid State Reaction Method ◽  
Raw Material ◽  
X Ray Diffraction ◽  
Solid State Method ◽  
X Ray ◽  
General Investigation

Hospho-material of olivine, LiMnPO4 identified as promising for cathode material generation next Lithium-ion battery and has been successfully synthesized by solid-state method with Li2Co3, 2MnO2, 2NH4H2PO4 as raw material. The influence of initial concentration of precursors at kalsinasi temperatures (400-800 ° C) flows with nitrogen. The purity and composition phase verified by x-ray diffraction analysis (XRD), scanning electron microscopy (SEM), spectroscopy, energy Dispersive x-ray Analysis (EDS), Raman spectra. General investigation shows that there is a correlation between the concentration of precursors, the temperature and the temperature of sintering kalsinasi that can be exploited to design lithium-ion next generation.

Mineralogical and geochemical characterization of archaeological ceramics from the 16th century El Badi Palace, Morocco

Clay Minerals ◽  
2018 ◽  
Vol 53 (3) ◽  
pp. 459-470
Author(s):  
Mouhssin El Halim ◽  
Lahcen Daoudi ◽  
Meriam El Ouahabi ◽  
Valérie Rousseau ◽  
Catherine Cools ◽  
...  
Keyword(s):  
Sixteenth Century ◽  
Chemical Characterization ◽  
Raw Material ◽  
Maximum Temperature ◽  
X Ray Diffraction ◽  
Archaeological Ceramics ◽  
Geochemical Characterization ◽  
X Ray ◽  
Firing Tests

ABSTRACTTextural, mineralogical and chemical characterization of archaeological ceramics (zellige) from El Badi Palace (Marrakech, Morocco), the main Islamic monument from the Saadian period (sixteenth century), has been performed to enhance restoration and to determine the technology of manufacturing. A multi-analytical approach based on optical and scanning electron microscopy, cathodoluminescence, X-ray fluorescence and X-ray diffraction was used. Re-firing tests on ceramic supports were also performed to determine the firing temperatures used by the Saadian artisans. A calcareous clay raw material was used to manufacture these decorative ceramics. The sherds were fired at a maximum temperature of 800°C in oxidizing atmosphere. The low firing temperature for ‘zellige’ facilitates cutting of the pieces, but also causes fragility in these materials due to the absence of vitreous phases.

Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part I. Microstructural Characterization of Nanosemicrystalline Si3N4 Powders

1998 ◽  
Vol 13 (9) ◽  
pp. 2580-2587 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Microstructural Characterization ◽  
Degree Of Crystallinity ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Transmission Electron ◽  
Wet Chemical ◽  
Si3n4 Ceramics

The characteristics of nanosized silicon nitride powders with doped Y2O3 and Al2O3 fabricated by a plasma-reacted chemical process were investigated. The chemical compositions of the powders were analyzed by wet chemical analysis. The morphology and the size distribution were determined by transmission electron microscopy (TEM). TEM with energy dispersive spectroscopy (EDS) was used to verify the existence of sintering additives in each individual particle. The crystal structure of the powders was identified by the selected area diffraction pattern (SADP). X-ray diffraction (XRD) technique was used for phase analysis and the measurement of degree of crystallinity. The characteristics of chemical bonding was analyzed by using Fourier transform infrared spectroscopy (FTIR).

Applications of X-ray microdiffraction in the imaging industry

2006 ◽  
Vol 21 (2) ◽  
pp. 91-96 ◽  
Author(s):  
Thomas N. Blanton
Keyword(s):  
Case Studies ◽  
Digital Imaging ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructure Morphology ◽  
Materials Used ◽  
Characterization Of Materials

Characterization of materials used in the digital imaging industry has been performed using micro X-ray diffraction (microXRD) techniques. Case studies are described that demonstrate the use of microXRD for identification of phases, texture, and microstructure morphology of components used in imaging applications.

Sign in / Sign up

Export Citation Format

Share Document