scholarly journals Hydrogen resistance to knock combustion in spark ignition internal combustion engines

2011 ◽  
Vol 144 (1) ◽  
pp. 13-19
Author(s):  
Stanisław SZWAJA
Keyword(s):  
Compression Ratio ◽  
Internal Combustion Engines ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Pressure Pulsations ◽  
Combustion Analysis ◽  
Dual Nature ◽  
The Moment ◽  
High Pass ◽  
Hydrogen Resistance

The results of investigations focusing on knock combustion analysis of a hydrogen-fueled engine have been presented in the paper. Knock intensity was determined as the intensity of the in-cylinder combustion pressure pulsations (recorded with a sampling frequency of 100 kHz) and filtered through high-pass filtering with cut-off frequency of 3.5 kHz. The research was conducted on the CFR engine with a variable compression ratio ranging from 6 to 14. The research has shown a rapid increase in pressure pulsations amplitude was observed while the compression ratio was changed from 11 to 12. This was interpreted as a result of in-cylinder hydrogen-air mixture self-ignition at the end of the spark ignition controlled combustion. Supporting this observation the theorem of dual nature of hydrogen knock combustion was postulated. Intensity of the pressure pulsations that accompany normal combustion without hydrogen self-ignition was in an exponential correlation with the compression ratio, which directly translates into a similar correlation of the pulsations and temperature of hydrogen-air mixture at the moment of ignition.

scholarly journals Analysis of thermodynamic parameters in spark ignition VCR engine

2019 ◽  
Vol 294 ◽  
pp. 05001
Author(s):  
Patryk Urbański ◽  
Maciej Bajerlein ◽  
Jerzy Merkisz ◽  
Andrzej Ziółkowski ◽  
Dawid Gallas
Keyword(s):  
Thermodynamic Parameters ◽  
Motion Analysis ◽  
Internal Combustion Engines ◽  
Initial Conditions ◽  
Combustion Process ◽  
Internal Combustion ◽  
3D Models ◽  
Spark Ignition ◽  
Combustion Engines ◽  
Combustion Processes

3D models of Szymkowiak and conventional engines were created in the Solidworks program. During the motion analysis, the characteristics of the piston path were analyzed for the two considered engine units. The imported file with the generated piston routes was used in the AVL Fire program, which simulated combustion processes in the two engines with identical initial conditions. The configurations for two different compression ratios were taken into account. The basic thermodynamic parameters occurring during the combustion process in internal combustion engines were analyzed.

Optimization of the Charge Motion in Internal Combustion Engines Driven by Sewage Gas for CHP-Units

2017 ◽  
Author(s):  
Lucas Konstantinoff ◽  
Lukas Möltner ◽  
Martin Pillei ◽  
Thomas Steiner ◽  
Thomas Dornauer ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Engine Performance ◽  
Internal Combustion ◽  
Optical Methods ◽  
Combustion Engines ◽  
Charge Motion ◽  
Combustion Analysis ◽  
Valve Seat ◽  
Test Engine ◽  
Indication System

In this study, the influence of the charge motion on the internal combustion in a spark ignition sewage gas-driven engine (150 kW) for combined heat and power units was investigated. For this purpose, the geometry of the combustion chamber in the immediate vicinity to the inlet valve seats was modified. The geometrical modification measures were conducted iteratively by integrative determination of the swirl motion on a flow bench, by laser-optical methods and consecutively by combustion analysis on a test engine. Two different versions of cylinder heads were characterized by dimensionless flow and swirl numbers prior to testing their on-engine performance. Combustion analysis was conducted with a cylinder pressure indication system for partial and full load, meeting the mandatory NOx limit of 500 mg m−3. Subsuming the flow bench results, the new valve seat design has a significant enhancing impact on the swirl motion but it also leads to disadvantages concerning the volumetric efficiency. A comparative consideration of the combustion rate delivers that the increased swirl motion results in a faster combustion, hence in a higher efficiency. In summary, the geometrical modifications close to the valve seat result in increased turbulence intensity. It was proven that this intensification raises the ratio of efficiency by 1.6%.

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

Development of the Control and Acquisition System for a Natural-Gas Spark-Ignition Engine Test Bench

2019 ◽  
Author(s):  
Lorenzo Gasbarro ◽  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu ◽  
Luca Ambrogi ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Test Bench ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Acquisition System ◽  
Combustion Engines ◽  
Engine Test ◽  
New Sensors

Abstract Investigations using laboratory test benches are the most common way to find the technological solutions that will increase the efficiency of internal combustion engines and curtail their emissions. In addition, the collected experimental data are used by the CFD community to develop engine models that reduce the time-to-market. This paper describes the steps made to increase the reliability of engine experiments performed in a heavy-duty natural-gas spark-ignition engine test-cell such as the design of the control and data acquisition system based on Modbus TCP communication protocol. Specifically, new sensors and a new dynamometer controller were installed. The operation of the improved test bench was investigated at several operating conditions, with data obtained at both high- and low-sampling rates. The results indicated a stable test bench operation.

A comparative study of the effect of compression ratio on the efficiency and flame development angle in a Cooperative Fuel Research engine fueled with binary gasoline–alcohol blends

2019 ◽  
pp. 146808741985910 ◽  
Author(s):  
Guillermo Rubio-Gómez ◽  
Lis Corral-Gómez ◽  
David Rodriguez-Rosa ◽  
Fausto A Sánchez-Cruz ◽  
Simón Martínez-Martínez
Keyword(s):  
Comparative Study ◽  
Compression Ratio ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Flame Development ◽  
The Impact

In the last few years, increasing concern about the harmful effects of the use of fossil fuels in internal combustion engines has been observed. In addition, the limited availability of crude oil has driven the interest in alternative fuels, especially biofuels. In the context of spark ignition engines, bioalcohols are of great interest owing to their similarities and blend capacities with gasoline. Methanol and ethanol have been widely used, mainly due to their knocking resistance. Another alcohol of great interest is butanol, thanks to its potential of being produced as biofuel and its heat value closer to gasoline. In this study, a comparative study of gasoline–alcohol blend combustion, with up to 20% volume, with neat gasoline has been carried out. A single-cylinder, variable compression ratio, Cooperative Fuel Research-type spark ignition engine has been employed. The comparison is made in terms of fuel conversion efficiency and flame development angle. Relevant information related to the impact in the combustion process of the use of the three main alcohols used in blends with gasoline has been obtained.

Behavior Prediction Model in Gas Fueled Spark Ignition Internal Combustion Engines Turbocharged for Genset Application

2013 ◽  
Author(s):  
Jorge Duarte Forero ◽  
German Amador Diaz ◽  
Fabio Blanco Castillo ◽  
Lesme Corredor Martinez ◽  
Ricardo Vasquez Padilla
Keyword(s):  
Equivalence Ratio ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Combustion Engines ◽  
Gaseous Fuels ◽  
Methane Number

In this paper, a mathematical model is performed in order to analyze the effect of the methane number (MN) on knock tendency when spark ignition internal combustion engine operate with gaseous fuels produced from different thermochemical processes. The model was validated with experimental data reported in literature and the results were satisfactory. A general correlation for estimating the autoignition time of gaseous fuels in function of cylinder temperature, and pressure, equivalence ratio and methane number of the fuel was carried out. Livengood and Wu correlation is used to predict autoignition in function of the crank angle. This criterium is a way to predict the autoignition tendency of a fuel/air mixture under engine conditions and consider the ignition delay. A chemical equilibrium model which considers 98 chemical species was used in this research in order to simulate the combustion of the gaseous fuels at differents engine operating conditions. The effect of spark advance, equivalence ratio, methane number (MN), charge (inlet pressure) and inlet temperature (manifold temperature) on engine knocking is evaluated. This work, explore the feasibility of using syngas with low methane number as fuel for commercial internal combustion engines.

Sign in / Sign up

Export Citation Format

Share Document