scholarly journals Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers

2018 ◽  
Author(s):  
Enrique Soriano Heras ◽  
Fernando Blaya Haro ◽  
José María de Agustín del Burgo ◽  
Manuel Islán Marcos ◽  
Roberto d´Amato
Keyword(s):  
Low Cost ◽  
Normal Function ◽  
Primary Objective ◽  
Normal Operation ◽  
Fused Deposition Modelling ◽  
Optical Encoder ◽  
Design Concepts ◽  
Fused Deposition ◽  
3D Printers ◽  
The Cost

The main purpose of this paper is to present a system to detect extrusion failures in Fused Deposition Modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the Weighted Objectives Method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains coil filament, which were not spent because they were not sufficient to complete an impression and also printing models in two colours with only one extruder.

Effects of Build Orientations on Tensile Properties of PLA Material Processed by FDM

2014 ◽  
Vol 1044-1045 ◽  
pp. 31-34 ◽  
Author(s):  
Mst Faujiya Afrose ◽  
S.H. Masood ◽  
Mostafa Nikzad ◽  
Pio Iovenitti
Keyword(s):  
Tensile Properties ◽  
Low Cost ◽  
Testing Machine ◽  
Extrusion Process ◽  
Fused Deposition Modelling ◽  
Tensile Testing Machine ◽  
Thermoplastic Material ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printers

Fused Deposition Modelling (FDM) of thermoplastic materials is generally a well-known technology among all additive manufacturing (AM) technologies and therefore, it is essential to investigate the mechanical properties of such FDM processed materials. Several open-source and low cost AM machines, known as 3D Printers, have recently been developed using thermoplastic extrusion process based on the original FDM technology. Many of these 3D Printers use Polylactic Acid (PLA) plastic for building parts. The main objective of this paper is to investigate the tensile properties of the PLA thermoplastic material processed by the Cube-2 3D Printer. In this study, the dog-bone sized PLA specimens are printed in different build orientations and a Zwick Z010 tensile testing machine is used to determine the tensile properties of PLA in different build orientation.

+TUO project: low cost 3D printers as helpful tool for small communities with rheumatic diseases

2015 ◽  
Vol 21 (5) ◽  
pp. 491-505 ◽  
Author(s):  
Francesca Ostuzzi ◽  
Valentina Rognoli ◽  
Jelle Saldien ◽  
Marinella Levi
Keyword(s):  
Rheumatic Diseases ◽  
Low Cost ◽  
Assistive Devices ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Small Communities ◽  
Entry Level ◽  
Fused Deposition ◽  
Innovative Products ◽  
3D Printers

Purpose – This paper aims to present a pilot study’s aims to identify opportunities and limits deriving from the use of low-cost 3D printing (3DP), fused deposition modelling (FDM), open-source technologies in co-design and co-production processes involving persons with rheumatic diseases (RDs). Design/methodology/approach – In the paper, the authors outline why the use of low-cost, entry-level FDM can be meaningful for this scenario, implying a complete sharing of the design and the production phases of small assistive devices. The +TUO process is composed of several stages, among which the generative session represents the core. Findings – This study highlights as the introduction of this low-cost technology in co-generative processes with people with RDs is a real challenge that can lead to new products and solutions, and that can sustain a social and local manufacturing approach for people facing a specific disablement. Research limitations/implications – This research is a first step of a broader research, new researches are going to explore further details related with the technology and of the adopted method. Practical implications – Involving actively, the end user during the creation process can bring advantages such as meeting more precisely their needs and create innovative products, as shown in the text. Social implications – For people living with RDs, an occupation is important to sustain a process of empowerment. Adopting assistive devices supports daily activities and facilitates the occupation. Originality/value – +TUO is a pilot study that explore a topic already discussed in the scientific arena, without focusing on the specific use of low-cost 3DP technologies.

Plate auto-level system for fused deposition modelling (FDM) 3D printers

2017 ◽  
Vol 23 (2) ◽  
pp. 401-413 ◽  
Author(s):  
Enrique Soriano Heras ◽  
Fernando Blaya Haro ◽  
José María de Agustín del Burgo ◽  
Manuel Enrique Islán Marcos
Keyword(s):  
Design Methodology ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Open Hardware ◽  
Fused Deposition ◽  
Sensing System ◽  
3D Printers ◽  
The Cost ◽  
Ultrasound Sensing ◽  
Practical Implications

Purpose The purpose of this paper is to present a solution for the levelling plate of fused deposition modelling (FDM) additive manufacturing (AM) systems. This automatic levelling system is presented as an evolution of actual systems, which uses a new ultrasound sensing system. Design/methodology/approach After obtaining a prototype, different tests were conducted for getting a system which solves the level plate problem and can be mounted in any FDM AM machine. Several benchmark models were obtained and compared with current equipment concepts for the validity of the product. Findings All tests were performed with high accuracy, enabling the production of geometries that could not have been achieved without this novel system. Practical implications This development will enable experienced users to set aside the problems of calibration and focus on the purpose of this type of machines, making prototypes. Originality/value A system architecture has been developed and integrated into an open hardware AM system, allowing real-time adjustment of the plate during each layer, thus eliminating the need of levelling the plate, allowing to achieve easier printing, and without increasing the cost significantly.

Performance of Low-Cost 3D Printer in Medical Application

2021 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Azib Azhari Awang Dahan ◽  
Sharifah Imihezri Syed Shaharuddin ◽  
Nor Farah Huda Abd Halim
Keyword(s):  
Low Cost ◽  
Medical Application ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Layer By Layer ◽  
Total Deformation ◽  
Element Analysis ◽  
Porosity Level ◽  
Fused Deposition ◽  
Printing Parameters

Abstract Fused Deposition Modelling (FDM) is an additive manufacturing (AM) process that produces a physical object directly from a CAD design using layer-by-layer deposition of the filament material that is extruded via a nozzle. In industry, FDM has become one of the most used AM processes for the production of low batch quantity and functional prototypes, due to its safety, efficiency, reliability, low cost, and ability to process manufacturing-grade engineering thermoplastic. Recently, the market is flooded with the availability of low-cost printers produced by numerous companies. This research aims to investigate the effect of different porosity levels on a scaffold structure produced using a low-cost 3D printer. Comparisons of these porous structures were made in terms of Von-Mises strain, total deformation, as well as compressive stress. Various porosity levels were created by varying printing parameters, including layer height, infill density, and shell thickness by slicing the initial solid CAD file using Repetier Host 3D printing software. Finite Element Analysis (FEA) simulation was then performed on the created scaffold structures by using Ansys Workbench 19.2. The simulation result indicates that the greater porosity level will result in higher total deformation of the structure. Meanwhile, the compression test shows that the minimum strength value obtained was favourable at 22 MPa and had exceeded that of the trabecular femur (15 MPa). However, its porosity level (maximum at 52%) was still below that of the minimum threshold of porosity level of 70 percent. However, the printing parameters currently used can be adjusted in the future. Therefore, it was deduced that the low-cost 3D printer offers promising potential to fabricate different porosity structures with multiple outcomes.

scholarly journals Tensile Mechanical Behaviour of Multi-Polymer Sandwich Structures via Fused Deposition Modelling

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 651 ◽  
Author(s):  
David Moises Baca Lopez ◽  
Rafiq Ahmad
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Poly Lactic Acid ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Homogeneous Materials ◽  
Flexural Tests ◽  
High Level

The application of single homogeneous materials produced through the fused deposition modelling (FDM) technology restricts the production of high-level multi-material components. The fabrication of a sandwich-structured specimen with different material combinations using conventional thermoplastics such as poly (lactic acid) (PLA), acrylonitrile butadiene styrene (ABS) and high impact polystyrene (HIPS) through the filament-based extrusion process can demonstrate an improvement on its properties. This paper aims to assess among these materials, the best material sandwich-structured arrangement design, to enhance the mechanical properties of a part and to compare the results with the homogeneous materials selected. The samples were subjected to tensile testing to identify the tensile strength, elongation at break and Young’s modulus of each material combination. The experimental results demonstrate that applying the PLA-ABS-PLA sandwich arrangement leads to the best mechanical properties between these materials. This study enables users to consider sandwich structure designs as an alternative to manufacturing multi-material components using conventional and low-cost materials. Future work will consider the flexural tests to identify the maximum stresses and bending forces under pressure.

Investigations for partial denture casting by fused deposition modelling-assisted chemical vapour smoothing

2020 ◽  
Vol 40 (5) ◽  
pp. 745-754
Author(s):  
Gurpartap Singh ◽  
Rupinder Singh ◽  
S.S. Bal
Keyword(s):  
Ph Value ◽  
Low Cost ◽  
Chemical Vapour ◽  
Dimensional Accuracy ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
View Point ◽  
Content Type ◽  
Fused Deposition ◽  
Set Up

Purpose The purpose of this study is to investigate dimensional accuracy (Δd), surface roughness (Ra) and micro hardness (HV) of partial dentures (PD) prepared with synergic combination of fused deposition modelling (FDM) assisted chemical vapour smoothing (CVS) patterns and conventional dental casting (DC) from multi-factor optimization view point. Design/methodology/approach The master pattern for PD was prepared with acrylonitrile butadiene styrene (ABS) thermoplastic on FDM set-up (one of the low cost additive manufacturing process) followed by CVS process. The final PD as functional prototypes was casted with nickel–chromium-based (Ni-Cr) alloy by varying Ni% (Z). The other input parameters were powder to water ratio P/W (X) and pH value (Y) of water used. Findings The results of this study suggest that for controlling the Δd and Ra of the PD, most important factor is X, followed by Z. For hardness of PD, the most important factor is Z. But from overall optimization viewpoint, the best settings are X-100/12, Y-10 and Z-61% (in Ni-Cr alloy). Further, based upon X-bar chart (for HV), the FDM-assisted DC process used for preparation of PD is statistically controlled. Originality/value This study highlights that PD prepared with X-100/12, Y-10 and Z-61% gives overall better results from multi-factor optimization view point. Finally, X-bar chart has been plotted to understand the statistical nature of the synergic combination of FDM, CVS and DC.

scholarly journals Representative Volume Element (RVE) Analysis for Mechanical Characterization of Fused Deposition Modeled Components

Polymers ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 3555
Author(s):  
Patrich Ferretti ◽  
Gian Maria Santi ◽  
Christian Leon-Cardenas ◽  
Elena Fusari ◽  
Giampiero Donnici ◽  
...  
Keyword(s):  
Representative Volume Element ◽  
Low Cost ◽  
Volume Element ◽  
Additive Manufacture ◽  
Fused Deposition Modelling ◽  
Structural Element ◽  
Fused Deposition ◽  
Representative Volume ◽  
Wide Range ◽  
3D Printed

Additive manufacturing processes have evolved considerably in the past years, growing into a wide range of products through the use of different materials depending on its application sectors. Nevertheless, the fused deposition modelling (FDM) technique has proven to be an economically feasible process turning additive manufacture technologies from consumer production into a mainstream manufacturing technique. Current advances in the finite element method (FEM) and the computer-aided engineering (CAE) technology are unable to study three-dimensional (3D) printed models, since the final result is highly dependent on processing and environment parameters. Because of that, an in-depth understanding of the printed geometrical mesostructure is needed to extend FEM applications. This study aims to generate a homogeneous structural element that accurately represents the behavior of FDM-processed materials, by means of a representative volume element (RVE). The homogenization summarizes the main mechanical characteristics of the actual 3D printed structure, opening new analysis and optimization procedures. Moreover, the linear RVE results can be used to further analyze the in-deep behavior of the FDM unit cell. Therefore, industries could perform a feasible engineering analysis of the final printed elements, allowing the FDM technology to become a mainstream, low-cost manufacturing process in the near future.

scholarly journals Investigations for In-house prepared Biocompatible Feed Stock Filament of Fused Deposition Modelling: A Process Capability study

2019 ◽  
Vol 48 (1) ◽  
pp. 18-23
Author(s):  
Nishant Ranjan ◽  
Rupinder Singh ◽  
IPS Ahuja
Keyword(s):  
Control Charts ◽  
Low Cost ◽  
Process Capability ◽  
Dimensional Accuracy ◽  
Fused Deposition Modelling ◽  
Twin Screw Extrusion ◽  
Fused Deposition ◽  
Feed Stock ◽  
Screw Extrusion ◽  
Twin Screw

Fused deposition modelling (FDM) is one of the low cost additive manufacturing (AM) process. The feed stock filament of FDM is the only consumable in the process and by preparing (in-house) bio compatible feed stock filament the application domain can be increased. Some studies have reported the use of twin screw extrusion (TSE) process for preparation of bio compatible feed stock filament (comprising of polyvinyl chloride (PVC) and polypropylene (PP) and hydroxyapatite (HAp) particles) with improved mechanical, dimensional and thermal properties, for commercial FDM setup. But hitherto very less has been reported on process capability of in-house prepared biocompatible feed stock filament. In the present work statistical analysis (for tensile strength, hardness and dimensional accuracy) has been performed for investigations of process capability. The results have been also supported by control charts (X-chart and R-chart) based upon the best feedstock filament wire.

The Study and Development of Factor Affecting the Smoothness in 3D Printed Part Surface Treatment via Acetone Vapor

2019 ◽  
Vol 821 ◽  
pp. 174-180
Author(s):  
Ramil Kesvarakul ◽  
Khompee Limpadapun
Keyword(s):  
Surface Finish ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Poor Quality ◽  
Industrial Applications ◽  
Fused Deposition Modelling ◽  
Dramatic Improvement ◽  
Acetone Vapor ◽  
Post Processing ◽  
Fused Deposition

Fused Deposition Modelling (FDM) has been extensively used in low-cost printers. However, the fundamental working principle (layered manufacturing) is resulted in the poor quality of the surface texture, the dimensional inaccuracy of fabricated parts, the limits its domain all issues often take place in precision industrial applications. In this paper, initially FDM based acrylonitrile butadiene styrene (ABS) model have been fabricated. In the post-processing stage, the vapor of acetone has been applied to the specimen. Then the changes in the surface finish and surface roughness have been investigated. The study highlighted that the post-processing of ABS specimen with acetone vapor treatment resulted in dramatic improvement of surface finish. Finally, parameter setting that gave the acceptable results while considering all the responses simultaneously.

Sign in / Sign up

Export Citation Format

Share Document