Effects of Build Orientations on Tensile Properties of PLA Material Processed by FDM

2014 ◽  
Vol 1044-1045 ◽  
pp. 31-34 ◽  
Author(s):  
Mst Faujiya Afrose ◽  
S.H. Masood ◽  
Mostafa Nikzad ◽  
Pio Iovenitti
Keyword(s):  
Tensile Properties ◽  
Low Cost ◽  
Testing Machine ◽  
Extrusion Process ◽  
Fused Deposition Modelling ◽  
Tensile Testing Machine ◽  
Thermoplastic Material ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printers

Fused Deposition Modelling (FDM) of thermoplastic materials is generally a well-known technology among all additive manufacturing (AM) technologies and therefore, it is essential to investigate the mechanical properties of such FDM processed materials. Several open-source and low cost AM machines, known as 3D Printers, have recently been developed using thermoplastic extrusion process based on the original FDM technology. Many of these 3D Printers use Polylactic Acid (PLA) plastic for building parts. The main objective of this paper is to investigate the tensile properties of the PLA thermoplastic material processed by the Cube-2 3D Printer. In this study, the dog-bone sized PLA specimens are printed in different build orientations and a Zwick Z010 tensile testing machine is used to determine the tensile properties of PLA in different build orientation.

scholarly journals Tensile Mechanical Behaviour of Multi-Polymer Sandwich Structures via Fused Deposition Modelling

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 651 ◽  
Author(s):  
David Moises Baca Lopez ◽  
Rafiq Ahmad
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Acrylonitrile Butadiene Styrene ◽  
Extrusion Process ◽  
Poly Lactic Acid ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Homogeneous Materials ◽  
Flexural Tests ◽  
High Level

The application of single homogeneous materials produced through the fused deposition modelling (FDM) technology restricts the production of high-level multi-material components. The fabrication of a sandwich-structured specimen with different material combinations using conventional thermoplastics such as poly (lactic acid) (PLA), acrylonitrile butadiene styrene (ABS) and high impact polystyrene (HIPS) through the filament-based extrusion process can demonstrate an improvement on its properties. This paper aims to assess among these materials, the best material sandwich-structured arrangement design, to enhance the mechanical properties of a part and to compare the results with the homogeneous materials selected. The samples were subjected to tensile testing to identify the tensile strength, elongation at break and Young’s modulus of each material combination. The experimental results demonstrate that applying the PLA-ABS-PLA sandwich arrangement leads to the best mechanical properties between these materials. This study enables users to consider sandwich structure designs as an alternative to manufacturing multi-material components using conventional and low-cost materials. Future work will consider the flexural tests to identify the maximum stresses and bending forces under pressure.

Identification of the Mechanical Characteristics of 3D Printed NinjaFlex®

2019 ◽  
Author(s):  
Patrick Messimer ◽  
Brendan O’Toole ◽  
Mohamed Trabia
Keyword(s):  
Tensile Properties ◽  
Mechanical Characteristics ◽  
Thermoplastic Polyurethane ◽  
Longitudinal Axis ◽  
Fused Deposition Modelling ◽  
Wearable Electronics ◽  
Limited Information ◽  
Fused Deposition ◽  
Axis Parallel ◽  
3D Printers

Abstract NinjaFlex is a flexible thermoplastic polyurethane (TPU) material manufactured for use with Fused Deposition Modelling 3D printers. It is widely available, relatively inexpensive, and is useful in various applications including gaskets, wearable electronics, and customized prosthetics because of its great flexibility and strength. The objective of this research was to expand on the limited information available regarding the mechanical characteristics of NinjaFlex and learn how infill density and printing orientation influence those characteristics. An experiment was designed using the ASTM D638-14 standard to evaluate tensile properties of NinjaFlex specimens printed in two different orientations with their longitudinal axis parallel to the printing surface and with their longitudinal axis normal to the printing surface. Four different infill densities were used. Specimens were subjected to tensile loading along their longitudinal axes. A calibrated load cell measured applied force while a camera filmed the experiment for determining the corresponding extension using computer vision methods. The results show that NinjaFlex has sizably greater ultimate strength, elongation, and toughness when loaded parallel to its print layers then when loaded normal to its print layers. The effects of infill density on tensile properties vary depending on loading direction relative to the print layer direction.

+TUO project: low cost 3D printers as helpful tool for small communities with rheumatic diseases

2015 ◽  
Vol 21 (5) ◽  
pp. 491-505 ◽  
Author(s):  
Francesca Ostuzzi ◽  
Valentina Rognoli ◽  
Jelle Saldien ◽  
Marinella Levi
Keyword(s):  
Rheumatic Diseases ◽  
Low Cost ◽  
Assistive Devices ◽  
Fused Deposition Modelling ◽  
Content Type ◽  
Small Communities ◽  
Entry Level ◽  
Fused Deposition ◽  
Innovative Products ◽  
3D Printers

Purpose – This paper aims to present a pilot study’s aims to identify opportunities and limits deriving from the use of low-cost 3D printing (3DP), fused deposition modelling (FDM), open-source technologies in co-design and co-production processes involving persons with rheumatic diseases (RDs). Design/methodology/approach – In the paper, the authors outline why the use of low-cost, entry-level FDM can be meaningful for this scenario, implying a complete sharing of the design and the production phases of small assistive devices. The +TUO process is composed of several stages, among which the generative session represents the core. Findings – This study highlights as the introduction of this low-cost technology in co-generative processes with people with RDs is a real challenge that can lead to new products and solutions, and that can sustain a social and local manufacturing approach for people facing a specific disablement. Research limitations/implications – This research is a first step of a broader research, new researches are going to explore further details related with the technology and of the adopted method. Practical implications – Involving actively, the end user during the creation process can bring advantages such as meeting more precisely their needs and create innovative products, as shown in the text. Social implications – For people living with RDs, an occupation is important to sustain a process of empowerment. Adopting assistive devices supports daily activities and facilitates the occupation. Originality/value – +TUO is a pilot study that explore a topic already discussed in the scientific arena, without focusing on the specific use of low-cost 3DP technologies.

scholarly journals Filament Advance Detection Sensor for Fused Deposition Modelling 3D Printers

2018 ◽  
Author(s):  
Enrique Soriano Heras ◽  
Fernando Blaya Haro ◽  
José María de Agustín del Burgo ◽  
Manuel Islán Marcos ◽  
Roberto d´Amato
Keyword(s):  
Low Cost ◽  
Normal Function ◽  
Primary Objective ◽  
Normal Operation ◽  
Fused Deposition Modelling ◽  
Optical Encoder ◽  
Design Concepts ◽  
Fused Deposition ◽  
3D Printers ◽  
The Cost

The main purpose of this paper is to present a system to detect extrusion failures in Fused Deposition Modelling (FDM) 3D printers by sensing that the filament is moving forward properly. After several years using these kind of machines, authors detected that there is not any system to detect the main problem in FDM machines. Authors thought in different sensors and used the Weighted Objectives Method, one of the most common evaluation methods, for comparing design concepts based on an overall value per design concept. Taking into account the obtained scores of each specification, the best choice for this work is the optical encoder. Once the sensor is chosen, it is necessary to design de part where it will be installed without interfering with the normal function of the machine. To do it, photogrammetry scanning methodology was employed. The developed device perfectly detects the advance of the filament without affecting the normal operation of the machine. Also, it is achieved the primary objective of the system, avoiding loss of material, energy and mechanical wear, keeping the premise of making a low-cost product that does not significantly increase the cost of the machine. This development has made it possible to use the printer with remains coil filament, which were not spent because they were not sufficient to complete an impression and also printing models in two colours with only one extruder.

Performance of Low-Cost 3D Printer in Medical Application

2021 ◽  
Author(s):  
Nor Aiman Sukindar ◽  
Azib Azhari Awang Dahan ◽  
Sharifah Imihezri Syed Shaharuddin ◽  
Nor Farah Huda Abd Halim
Keyword(s):  
Low Cost ◽  
Medical Application ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Layer By Layer ◽  
Total Deformation ◽  
Element Analysis ◽  
Porosity Level ◽  
Fused Deposition ◽  
Printing Parameters

Abstract Fused Deposition Modelling (FDM) is an additive manufacturing (AM) process that produces a physical object directly from a CAD design using layer-by-layer deposition of the filament material that is extruded via a nozzle. In industry, FDM has become one of the most used AM processes for the production of low batch quantity and functional prototypes, due to its safety, efficiency, reliability, low cost, and ability to process manufacturing-grade engineering thermoplastic. Recently, the market is flooded with the availability of low-cost printers produced by numerous companies. This research aims to investigate the effect of different porosity levels on a scaffold structure produced using a low-cost 3D printer. Comparisons of these porous structures were made in terms of Von-Mises strain, total deformation, as well as compressive stress. Various porosity levels were created by varying printing parameters, including layer height, infill density, and shell thickness by slicing the initial solid CAD file using Repetier Host 3D printing software. Finite Element Analysis (FEA) simulation was then performed on the created scaffold structures by using Ansys Workbench 19.2. The simulation result indicates that the greater porosity level will result in higher total deformation of the structure. Meanwhile, the compression test shows that the minimum strength value obtained was favourable at 22 MPa and had exceeded that of the trabecular femur (15 MPa). However, its porosity level (maximum at 52%) was still below that of the minimum threshold of porosity level of 70 percent. However, the printing parameters currently used can be adjusted in the future. Therefore, it was deduced that the low-cost 3D printer offers promising potential to fabricate different porosity structures with multiple outcomes.

Effect of heat treatment on mechanical properties of 3D printed polylactic acid parts

2021 ◽  
Vol 63 (1) ◽  
pp. 73-78
Author(s):  
Pulkin Gupta ◽  
Sudha Kumari ◽  
Abhishek Gupta ◽  
Ankit Kumar Sinha ◽  
Prashant Jindal
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Polylactic Acid ◽  
Recrystallization Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Maximum Decrease ◽  
3D Printed

Abstract Fused deposition modelling (FDM) is a layer-by-layer manufacturing process type of 3D-printing (3DP). Significant variation in the mechanical properties of 3D printed specimens is observed because of varied process parameters and interfacial bonding between consecutive layers. This study investigates the influence of heat treatment on the mechanical strength of FDM 3D printed Polylactic acid (PLA) parts with constant 3DP parameters and ambient conditions. To meet the objectives, 7 sets, each containing 5 dog-bone shaped samples, were fabricated from commercially available PLA filament. Each set was subjected to heat treatment at a particular temperature for 1 h and cooled in the furnace itself, while one set was left un-treated. The temperature for heat treatment (Th) varied from 30 °C to 130 °C with increments of 10 °C. The heat-treated samples were characterized under tensile loading of 400 N and mechanical properties like Young’s modulus (E), Strain % ( ε ) and Stiffness (k) were evaluated. On comparing the mechanical properties of heat-treated samples to un-treated samples, significant improvements were observed. Heat treatment also altered the geometries of the samples. Mechanical properties improved by 4.88 % to 10.26 % with the maximum being at Th of 110 °C and below recrystallization temperature (Tr) of 65 °C. Deformations also decreased significantly at higher temperatures above 100 °C, by a maximum of 36.06 %. The dimensions of samples showed a maximum decrease of 1.08 % in Tr range and a maximum decrease of 0.31 % in weight at the same temperature. This study aims to benefit the society by establishing suitable Th to recover the lost strength in PLA based FDM 3D printed parts.

Thermomechanical investigations of PEKK-HAp-CS composites

2019 ◽  
Vol 233 (11) ◽  
pp. 1196-1203
Author(s):  
Rupinder Singh ◽  
Gurchetan Singh ◽  
Jaskaran Singh ◽  
Ranvijay Kumar ◽  
Md Mustafizur Rahman ◽  
...  
Keyword(s):  
Melt Flow Index ◽  
Extrusion Process ◽  
Flow Index ◽  
Fused Deposition Modelling ◽  
Index Test ◽  
Melt Flow ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Ether Ketone ◽  
Input Variables

In this experimental study, a composite of poly-ether-ketone-ketone by reinforcement of hydroxyapatite and chitosan has been prepared for possible applications as orthopaedic scaffolds. Initially, different weight percentages of hydroxyapatite and chitosan were reinforced in the poly-ether-ketone-ketone matrix and tested for melt flow index in order to check the flowability of different compositions/proportions. Suitable compositions revealed by the melt flow index test were then taken forward for the extrusion of filament required for fused deposition modelling. For thermomechanical investigations, Taguchi-based design of experiments has been used with input variables in the extrusion process as follows: temperature, load applied and different composition/proportions. The specimens in the form of feedstock filament produced by the extrusion process were made to undergo tensile testing. The specimens were also inspected by differential scanning calorimetry and photomicrographs. Finally, the specimen showing the best performance from the thermomechanical viewpoint has been selected to extrude the filament for the fused deposition modelling process.

scholarly journals Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2497 ◽  
Author(s):  
Yao Li ◽  
Yan Lou
Keyword(s):  
Tensile Strength ◽  
3D Printing ◽  
Tensile Properties ◽  
Bending Strength ◽  
Utilization Rate ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Molded Parts ◽  
Injection Molded ◽  
Printing Direction

Compared with laser-based 3D printing, fused deposition modelling (FDM) 3D printing technology is simple and safe to operate and has a low cost and high material utilization rate; thus, it is widely used. In order to promote the application of FDM 3D printing, poly-ether-ether-ketone (PEEK) was used as a printing material to explore the effect of multi-factor coupling such as different printing temperatures, printing directions, printing paths, and layer thicknesses on the tensile strength, bending strength, crystallinity, and grain size of FDM printed PEEK parts. The aim was to improve the mechanical properties of the 3D printed PEEK parts and achieve the same performance as the injection molded counterparts. The results show that when the thickness of the printed layer is 0.1 mm and the printing path is 180° horizontally at 525 °C, the tensile strength of the sample reaches 87.34 MPa, and the elongation reaches 38%, which basically exceeds the tensile properties of PEEK printed parts reported in previous studies and is consistent with the tensile properties of PEEK injection molded parts. When the thickness of the printed layer is 0.3 mm, the printing path is 45°, and with vertical printing direction at a printing temperature of 525 °C, the bending strength of the sample reaches 159.2 MPa, which exceeds the bending performance of injection molded parts by 20%. It was also found that the greater the tensile strength of the printed specimen, the more uniform the size of each grain, and the higher the crystallinity of the material. The highest crystallinity exceeded 30%, which reached the crystallinity of injection molded parts.

Investigations for partial denture casting by fused deposition modelling-assisted chemical vapour smoothing

2020 ◽  
Vol 40 (5) ◽  
pp. 745-754
Author(s):  
Gurpartap Singh ◽  
Rupinder Singh ◽  
S.S. Bal
Keyword(s):  
Ph Value ◽  
Low Cost ◽  
Chemical Vapour ◽  
Dimensional Accuracy ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
View Point ◽  
Content Type ◽  
Fused Deposition ◽  
Set Up

Purpose The purpose of this study is to investigate dimensional accuracy (Δd), surface roughness (Ra) and micro hardness (HV) of partial dentures (PD) prepared with synergic combination of fused deposition modelling (FDM) assisted chemical vapour smoothing (CVS) patterns and conventional dental casting (DC) from multi-factor optimization view point. Design/methodology/approach The master pattern for PD was prepared with acrylonitrile butadiene styrene (ABS) thermoplastic on FDM set-up (one of the low cost additive manufacturing process) followed by CVS process. The final PD as functional prototypes was casted with nickel–chromium-based (Ni-Cr) alloy by varying Ni% (Z). The other input parameters were powder to water ratio P/W (X) and pH value (Y) of water used. Findings The results of this study suggest that for controlling the Δd and Ra of the PD, most important factor is X, followed by Z. For hardness of PD, the most important factor is Z. But from overall optimization viewpoint, the best settings are X-100/12, Y-10 and Z-61% (in Ni-Cr alloy). Further, based upon X-bar chart (for HV), the FDM-assisted DC process used for preparation of PD is statistically controlled. Originality/value This study highlights that PD prepared with X-100/12, Y-10 and Z-61% gives overall better results from multi-factor optimization view point. Finally, X-bar chart has been plotted to understand the statistical nature of the synergic combination of FDM, CVS and DC.

scholarly journals Mechanical and Physical Properties of Recycled-Carbon-Fiber-Reinforced Polylactide Fused Deposition Modelling Filament

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 190
Author(s):  
Nur’ain Wahidah Ya Omar ◽  
Norshah Aizat Shuaib ◽  
Mohd Haidiezul Jamal Ab Hadi ◽  
Azwan Iskandar Azmi ◽  
Muhamad Nur Misbah
Keyword(s):  
Surface Roughness ◽  
Carbon Fiber ◽  
Physical Properties ◽  
Tensile Properties ◽  
Fused Deposition Modelling ◽  
Fiber Reinforced ◽  
Porosity Level ◽  
Fused Deposition ◽  
Mechanical And Physical Properties ◽  
Carbon Fiber Reinforced

Carbon-fiber-reinforced plastic materials have attracted several applications, including the fused deposition modelling (FDM) process. As a cheaper and more environmentally friendly alternative to its virgin counterpart, the use of milled recycled carbon fiber (rCF) has received much attention. The quality of the feed filament is important to avoid filament breakage and clogged nozzles during the FDM printing process. However, information about the effect of material parameters on the mechanical and physical properties of short rCF-reinforced FDM filament is still limited. This paper presents the effect of fiber loading (10 wt%, 20 wt%, and 30 wt%) and fiber size (63 µm, 75 µm, and 150 µm) on the filament’s tensile properties, surface roughness, microstructure, porosity level, density, and water absorptivity. The results show that the addition of 63 µm fibers at 10 wt% loading can enhance filament tensile properties with minimal surface roughness and porosity level. The addition of rCF increased the density and reduced the material’s water intake. This study also indicates a clear trade-off between the optimized properties. Hence, it is recommended that the optimization of rCF should consider the final application of the product. The findings of this study provide a new manufacturing strategy in utilizing milled rCF in potential 3D printing-based applications.

Sign in / Sign up

Export Citation Format

Share Document