scholarly journals Evaluation of the Bioavailability and Translocation of Selected Mobile Chemical Species by Brassica juncea and Spinacea oleracea L for a South African Power Utility Coal Fly Ash

2018 ◽  
Author(s):  
Aluwani Shiridor Mashau ◽  
Mugera Wilson Gitari ◽  
Segun Ajayi Akinyemi
Keyword(s):  
Fly Ash ◽  
South African ◽  
Brassica Juncea ◽  
Coal Fly Ash ◽  
Chemical Species ◽  
Mineralogical Composition ◽  
Power Utility ◽  
Potential Health ◽  
X Ray ◽  
Spinacea Oleracea

This study evaluated the physicochemical, mineralogical properties, mobile chemical species’ bioavailability and translocation in Brassica juncea and Spinacea oleracea L plants of a South African coal fired power utility. Coal fly ash (CFA) disposal is associated with various environmental and health risks including air, soil, surface and ground water pollution due to the leaching of toxic chemical species; these ends up in food webs affecting  human health, while repeated inhalation causes bronchitis, silicosis, hair loss and lung cancer. The morphology, chemical, and mineralogical composition of CFA were determined using Scanning Electron Microscopy (SEM), X-ray fluorescence (XRF) and X-ray Diffraction, respectively. In pot culture experiments, S. oleracea L and B. juncea plants were grown in three sets of pots containing CFA (set 1), soil (set 2) and a mixture of CFA plus soil at ratio 1:1 (50% CFA: 50% soil) (set 3), while no plants were grown in set 4 as a control for the leachate samples. SEM showed that surface morphology of CFA has a lower degree of sphericity with irregular agglomerations of many particles. The XRF results revealed that CFA contains 43.65%, 22.68% and 10.89% of SiO2, Al2O3 and Fe2O3 respectively which indicate that the CFA is an alumino-silicate material. While XRD showed that the coal CFA contains mullite as a major phase followed by quartz mineral phases. Chemical species such as Fe, Mn, B, Ba and Zn were accumulated highly in most parts of the plant species. However, B. juncea showed higher potential to accumulate chemical species as compared to S. oleracea L. The bioconcentration and translocation factors (BF and TF) showed that B. juncea was the most effective in terms of bioconcentration and translocation of most of the chemical species. This indicates that B. juncea has potential in application for phytoremediation of CFA dumps and could contribute to remediation of CFA dumps and reduction of potential health and environmental impacts associated with CFA.

scholarly journals Evaluation of the Bioavailability and Translocation of Selected Heavy Metals by Brassica juncea and Spinacea oleracea L for a South African Power Utility Coal Fly Ash

2018 ◽  
Vol 15 (12) ◽  
pp. 2841 ◽  
Author(s):  
Aluwani Mashau ◽  
Mugera Gitari ◽  
Segun Akinyemi
Keyword(s):  
Heavy Metals ◽  
South African ◽  
Coal Fly Ash ◽  
Chemical Species ◽  
Growth Media ◽  
X Ray Diffraction ◽  
Power Utility ◽  
X Ray ◽  
Spinacea Oleracea ◽  
Pot Culture

This study evaluated the physicochemical and mineralogical properties, mobile chemical species bioavailability and translocation in Brassica juncea and Spinacea oleracea L. plants of a South African coal-fired power utility. Coal-fly-ash (CFA) disposal is associated with various environmental and health risks, including air, soil, surface, and groundwater pollution due to the leaching of toxic heavy metals; these ends up in food webs affecting human health, while repeated inhalation causes bronchitis, silicosis, hair loss, and lung cancer. The morphology and chemical and mineralogical composition of CFA were determined using Scanning Electron Microscopy (SEM), X-ray fluorescence (XRF), and X-ray diffraction, respectively. In pot-culture experiments, S. oleracea L. and B. juncea plants were grown in three sets of pots containing CFA (Set 1), soil (Set 2), and a mixture of CFA plus soil at a ratio of 1:1 (50% CFA: 50% soil, Set 3), while no plants were grown in Set 4 as a control for the leachate samples. SEM showed that the surface morphology of CFA has a lower degree of sphericity with the irregular agglomerations of many particles. XRF results revealed that CFA contains 43.65%, 22.68%, and 10.89% of SiO2, Al2O3, and Fe2O3, respectively, which indicates that CFA is an aluminosilicate material. X-ray diffraction (XRD) showed that CFA contains mullite as a major phase, followed by quartz mineral phases. Chemical species such as B, Ba, Mo, and Cr were occurring at higher concentrations in the leachates for most weeks in the pot-culture experiments, especially for CFA and soil + CFA growth media. However, there was a common trend for all growth media of chemical-species concentrations declining with time, which might have been caused by plant uptake or wash-off with water during irrigation; even for the growth media as well, where no plants were grown. Chemical species, such as Fe, Mn, B, Ba, and Zn, accumulated highly in most parts of the plant species. However, B. juncea showed higher potential to accumulate chemical species as compared to S. oleracea L. Bioconcentration and translocation factors (BF and TF) showed that B. juncea was the most effective in terms of bioconcentration and translocation of most of the chemical species. This indicates that B. juncea has potential in application for the phytoremediation of CFA dumps, and could contribute to the remediation of CFA dumps and the reduction of potential health and environmental impact associated with CFA.

scholarly journals Dynamic hydrothermal synthesis of xonotlite fibers by alkali silica extraction of fly ash

2019 ◽  
Vol 14 ◽  
pp. 155892501989034 ◽  
Author(s):  
Xu Peng
Keyword(s):  
Fly Ash ◽  
Hydrothermal Synthesis ◽  
Coal Fly Ash ◽  
Synthesis Method ◽  
Morphological Characteristics ◽  
Mineralogical Composition ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Silica Material

The silica leached from coal fly ash using alkali, via the hydrothermal method, can be used as the raw material for the synthesis of xonotlite fibers through the hydrothermal synthesis method. This investigation was made to examine how the fly ash desilicated liquid influences the crystal growth and microstructure of xonotlite fibers. The obtained samples were characterized by X-ray diffraction and scanning electron microscope techniques to investigate their mineralogical composition and morphological characteristics. The results indicated that the pure desilication liquid leached from coal fly ash could be used to prepare xonotlite fibers. Xonotlite fibers with single crystal characteristics and large aspect ratio of 100–400 were successfully fabricated from fly ash desilication liquid, which is used as the silica material, at 240°C for 6 h.

scholarly journals Preparation of Synthetic Zeolites from Coal Fly Ash by Hydrothermal Synthesis

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1267
Author(s):  
David Längauer ◽  
Vladimír Čablík ◽  
Slavomír Hredzák ◽  
Anton Zubrik ◽  
Marek Matik ◽  
...  
Keyword(s):  
Fly Ash ◽  
Coal Combustion ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Product Analysis ◽  
Coal Combustion Products ◽  
X Ray ◽  
Wide Range ◽  
Silica Alumina

Large amounts of coal combustion products (as solid products of thermal power plants) with different chemical and physical properties cause serious environmental problems. Even though coal fly ash is a coal combustion product, it has a wide range of applications (e.g., in construction, metallurgy, chemical production, reclamation etc.). One of its potential uses is in zeolitization to obtain a higher added value of the product. The aim of this paper is to produce a material with sufficient textural properties used, for example, for environmental purposes (an adsorbent) and/or storage material. In practice, the coal fly ash (No. 1 and No. 2) from Czech power plants was firstly characterized in detail (X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), particle size measurement, and textural analysis), and then it was hydrothermally treated to synthetize zeolites. Different concentrations of NaOH, LiCl, Al2O3, and aqueous glass; different temperature effects (90–120 °C); and different process lengths (6–48 h) were studied. Furthermore, most of the experiments were supplemented with a crystallization phase that was run for 16 h at 50 °C. After qualitative product analysis (SEM-EDX, XRD, and textural analytics), quantitative XRD evaluation with an internal standard was used for zeolitization process evaluation. Sodalite (SOD), phillipsite (PHI), chabazite (CHA), faujasite-Na (FAU-Na), and faujasite-Ca (FAU-Ca) were obtained as the zeolite phases. The content of these zeolite phases ranged from 2.09 to 43.79%. The best conditions for the zeolite phase formation were as follows: 4 M NaOH, 4 mL 10% LiCl, liquid/solid ratio of 30:1, silica/alumina ratio change from 2:1 to 1:1, temperature of 120 °C, process time of 24 h, and a crystallization phase for 16 h at 50 °C.

scholarly journals Characterization of Fly Ash Generated from Matla Power Station in Mpumalanga, South Africa

2012 ◽  
Vol 9 (4) ◽  
pp. 1788-1795 ◽  
Author(s):  
Olushola S. Ayanda ◽  
Olalekan S. Fatoki ◽  
Folahan A. Adekola ◽  
Bhekumusa J. Ximba
Keyword(s):  
Fly Ash ◽  
Inductively Coupled Plasma ◽  
Coal Fly Ash ◽  
Harmful Effect ◽  
Point Of Zero Charge ◽  
X Ray Diffraction ◽  
Power Station ◽  
X Ray ◽  
Inductively Coupled ◽  
Plasma Mass Spectrometry

In this study, fly ash was obtained from Matla power station and the physicochemical properties investigated. The fly ash was characterized by x-ray fluorescence, x-ray diffraction, scanning electron microscopy, and inductively coupled plasma mass spectrometry. Surface area, particle size, ash and carbon contents, pH, and point of zero charge were also measured. The results showed that the fly ash is alkaline and consists mainly of mullite (Al6Si2O13) and quartz (SiO2). Highly toxic metals As, Sb, Cd, Cr, and Pb as well as metals that are essential to health in trace amounts were also present. The storage and disposal of coal fly ash can thus lead to the release of leached metals into soils, surface and ground waters, find way into the ecological systems and then cause harmful effect to man and its environments.

Total reflection X-ray fluorescence analysis of fly ash from Bulgarian coal-fired power plants

2015 ◽  
Vol 69 (5) ◽  
Author(s):  
Albena K. Detcheva ◽  
Svilen E. Mitsiev ◽  
Paunka S. Vassileva ◽  
Juri H. Jordanov ◽  
Metody G. Karadjov ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Internal Standard ◽  
Fluorescence Analysis ◽  
Total Reflection ◽  
X Ray

AbstractThe contents of Cl, Ca, K, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Rb, Sr, Ba and Pb in raw coal fly ash from five Bulgarian power plants were determined by total reflection X-ray fluorescence (TXRF), using gallium as the internal standard. The samples were analysed as in slurry form in Triton

scholarly journals Adsorptive removal of various phenols from water by South African coal fly ash

Water SA ◽  
2012 ◽  
Vol 35 (1) ◽  
Author(s):  
JH Potgieter ◽  
SO Bada ◽  
SS Potgieter-Vermaak
Keyword(s):  
Fly Ash ◽  
South African ◽  
Coal Fly Ash ◽  
Adsorptive Removal

scholarly journals Composition and Morphology Characteristics of Magnetic Fractions of Coal Fly Ash Wastes Processed in High-Temperature Exposure in Thermal Power Plants

2019 ◽  
Vol 9 (9) ◽  
pp. 1964 ◽  
Author(s):  
Dinh-Hieu Vu ◽  
Hoang-Bac Bui ◽  
Bahareh Kalantar ◽  
Xuan-Nam Bui ◽  
Dinh-An Nguyen ◽  
...  
Keyword(s):  
Fly Ash ◽  
Power Plants ◽  
Coal Fly Ash ◽  
Thermal Power ◽  
Combustion Process ◽  
Mineralogical Composition ◽  
Striking Difference ◽  
Thermal Power Plants ◽  
Power Stations ◽  
Magnetic Components

Coal-fired power stations are one of the primary sources of power generation in the world. This will produce considerable amounts of fly ash from these power stations each year. To highlight the potential environmental hazards of these materials, this study is carried out to evaluate the characterization of fly ashes produced in thermal power plants in northern Vietnam. Fly ash was firstly fractionated according to size, and the fractions were characterized. Then, each of these fractions was analyzed with regard to their mineralogical features, morphological and physicochemical properties. The analytical results indicate a striking difference in terms of the characteristics of particles. It was found that magnetic fractions are composed of magnetite hematite and, to a lower rate, mullite, and quartz. Chemical analyses indicate that the non-magnetic components mainly consist of quartz and mullite as their primary mineral phases. As the main conclusion of this research, it is found that the magnetic and non-magnetic components differ in terms of shape, carbon content and mineralogical composition. In addition, it was found that magnetic components can be characterized as more spheroidal components compared to non-magnetic ones. This comprehensive characterization not only offers a certain guideline regarding the uses of different ash fractions but it will also provide valuable information on this common combustion process.

scholarly journals Coal fly ash: linking immersion freezing behavior and physicochemical particle properties

2018 ◽  
Vol 18 (19) ◽  
pp. 13903-13923 ◽  
Author(s):  
Sarah Grawe ◽  
Stefanie Augustin-Bauditz ◽  
Hans-Christian Clemen ◽  
Martin Ebert ◽  
Stine Eriksen Hammer ◽  
...  
Keyword(s):  
Fly Ash ◽  
Single Particle ◽  
Coal Fly Ash ◽  
Ice Nucleation ◽  
Freezing Behavior ◽  
Cloud Droplets ◽  
X Ray ◽  
Particle Properties ◽  
Cold Stage ◽  
Immersion Freezing

Abstract. To date, only a few studies have investigated the potential of coal fly ash particles to trigger heterogeneous ice nucleation in cloud droplets. The presented measurements aim at expanding the sparse dataset and improving process understanding of how physicochemical particle properties can influence the freezing behavior of coal fly ash particles immersed in water. Firstly, immersion freezing measurements were performed with two single particle techniques, i.e., the Leipzig Aerosol Cloud Interaction Simulator (LACIS) and the SPectrometer for Ice Nuclei (SPIN). The effect of suspension time on the efficiency of the coal fly ash particles when immersed in a cloud droplet is analyzed based on the different residence times of the two instruments and employing both dry and wet particle generation. Secondly, two cold-stage setups, one using microliter sized droplets (Leipzig Ice Nucleation Array) and one using nanoliter sized droplets (WeIzmann Supercooled Droplets Observation on Microarray setup) were applied. We found that coal fly ash particles are comparable to mineral dust in their immersion freezing behavior when being dry generated. However, a significant decrease in immersion freezing efficiency was observed during experiments with wet-generated particles in LACIS and SPIN. The efficiency of wet-generated particles is in agreement with the cold-stage measurements. In order to understand the reason behind the deactivation, a series of chemical composition, morphology, and crystallography analyses (single particle mass spectrometry, scanning electron microscopy coupled with energy dispersive X-ray microanalysis, X-ray diffraction analysis) were performed with dry- and wet-generated particles. From these investigations, we conclude that anhydrous CaSO4 and CaO – which, if investigated in pure form, show the same qualitative immersion freezing behavior as observed for dry-generated coal fly ash particles – contribute to triggering heterogeneous ice nucleation at the particle–water interface. The observed deactivation in contact with water is related to changes in the particle surface properties which are potentially caused by hydration of CaSO4 and CaO. The contribution of coal fly ash to the ambient population of ice-nucleating particles therefore depends on whether and for how long particles are immersed in cloud droplets.

Measuring Graphitic Carbon and Crystalline Minerals in Coals and Bottom Ashes

1987 ◽  
Vol 31 ◽  
pp. 343-349 ◽  
Author(s):  
David L. Wertz ◽  
Leo W. Collins ◽  
Franz Froelicher
Keyword(s):  
Energy Source ◽  
Fly Ash ◽  
Chemical Species ◽  
Primary Energy ◽  
Toxic Chemical ◽  
Atom Pair ◽  
Crystalline Phases ◽  
X Ray ◽  
X Ray Scattering ◽  
Lignite Fly Ash

AbstractThe use of coal, as either a primary energy source or as a source of feedstock chemicals, has been complicated by the noxious and toxic chemical species formed in its gaseous effluents and also by the huge quantities of ash vhich result from its processing. Both the noxious gases and the ash have been the subjects of Federal legislations.X-ray powder patterns (XRPP), composed of atom-pair and self x~ray scattering and the diffraction produced by crystalline phases, have long been used to investigate coals and particularly their combustion ashes (1-3). Over twenty different crystalline phases have recently been reported to exist in certain lignite fly ash (3). Analysis of the crystalline phases has typically been emphasized in previous papers involving coals and ashes, but the amorphous scattering has been given little treatment.

Sign in / Sign up

Export Citation Format

Share Document