scholarly journals Experimental research of the influence of a ferromagnetic core on the speed of an induction-dynamic release with turning anchor type

2021 ◽  
pp. 10-14
Author(s):  
Viktoriia Lytvynenko ◽  
Alexander Sereda ◽  
Iryna Varshamova ◽  
Olena Korol
Keyword(s):  
Semiconductor Device ◽  
Thermal Protection ◽  
Capacitor Bank ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Operation Time ◽  
Mutual Inductance ◽  
Electrodynamic Force ◽  
Ferromagnetic Core ◽  
Inductor Coil

Circuit breakers for overcurrent protection of semiconductor converters limit the duration and amplitude of the overcurrent at such a level that its thermal effect does not exceed the maximum allowable thermal protection index of the protected semiconductor device. The limitation of the thermal action of the short-circuit current is achieved by reducing the operation time of the circuit breaker. The design of the circuit breaker is changed in such a way that instead of the basic electromagnetic release is used an induction-dynamic release, which consists of an inductor with a ferromagnetic core and a rotary armature in the form of a copper disk. The electrodynamic force producing by the induction-dynamic release for quick operation is determined by the coefficient of mutual inductance of the inductor coil and the armature. Using of a ferromagnetic core entailed an increase in the coefficient of mutual inductance of the coil and armature, therefore, an increase in the electrodynamic force producing by the release, and a decrease in own tripping time of the circuit breaker. On a prototype, an experimental study of the proper operation time of the release was carried out at various values of the electrical parameters of the capacitor bank of the inductor power supply, the winding parameters of the inductor coil and the disk dimensions. The research results have proved both a decrease in the tripping time of the circuit breaker while conserving the energy of the capacitor bank of the inductor, and a decrease in the required energy of the capacitor bank to power the inductor while maintaining the minimum tripping time of the circuit breaker. Reducing the energy of the capacitor bank of the inductor made it possible to reduce the capacity and voltage of the capacitor bank of the supply of the release, and, consequently, its dimensions.

scholarly journals Modeling Operation of Liquid Metal Fuses When Breaking Overcurrents

2020 ◽  
Vol 178 ◽  
pp. 01060
Author(s):  
A V Kuznetsov ◽  
D S Aleksandrov ◽  
Y P Yurenkov
Keyword(s):  
Liquid Metal ◽  
Short Circuit ◽  
Time Moment ◽  
Circuit Breaker ◽  
Reference Points ◽  
Joint Operation ◽  
Pilot Studies ◽  
In Series ◽  
Current Limiter ◽  
Temperature Melting

This paper shows that successful switching of extremely high short-circuit currents I> 50 kA can be achieved by joint operation of a liquid-metal self-resetting current limiter and a circuit breaker connected in series. The type NFU-225 device from Mitsubishi was taken as an example. The time-current characteristic of joint operation of a liquid-metal self-resetting current-limiting device and a circuit breaker was compiled. However, further in the article physical processes occurring in a liquid-metal self-resetting current limiter with a complete transformation of fusible unit are considered. The result of work is modelling of operation of liquid-metal fuses when overcurrents are switched off based on the pilot studies obtained by the Japanese scientists. It is proposed to simulate the break process not at every time moment, but at specific time moments (reference points). At other time moments, current and voltage should be considered as approximately linearly changing characteristics. The work of current limiter can be represented by three stages: the pre-arc, the main arc and the final arc. If the current density is less than 1000 A/mm2, then the pre-arc operation stage of the current limiter includes the following sections for heating the fusible unit: primary heating to the melting temperature; melting and its transition to liquid state; secondary heating to evaporation temperature; evaporation of fusible unit.

scholarly journals Capacitor Commutation Method for MVDC Hybrid Circuit Breakers

Designs ◽  
2021 ◽  
Vol 5 (2) ◽  
pp. 28
Author(s):  
Hyosung Kim
Keyword(s):  
Short Circuit ◽  
Circuit Breaker ◽  
Reverse Current ◽  
Resonant Circuit ◽  
Power Circuit ◽  
Power Sources ◽  
Semiconductor Switch ◽  
Current Commutation ◽  
Dc Circuit Breaker ◽  
Hybrid Circuit

The medium voltage DC (MVDC) type system can connect multiple terminals to a common MVDC bus, so it is possible to connect several renewable DC power sources to the common MVDC bus, but a DC circuit breaker is needed to isolate short circuit accidents that may occur in the MVDC bus. For this purpose, the concept of a hybrid DC circuit breaker that takes advantage of a low conduction loss contact type switch and an arcless-breaking semiconductor switch has been proposed. During break the hybrid switch, a dedicated current commutation device is required to temporarily bypass the load current flowing through the main switch into a semiconductor switch branch. Existing current commutation methods include a proactive method and a reverse current injection method by a LC (Inductor-capacitor) resonant circuit. This paper proposes a power circuit of a new MVDC hybrid circuit breaker using a low withstanding voltage capacitor branch for commutation and a sequence controller according to it, and verifies its operation through an experiment.

Dependence of Short Circuit Breaking Current on its Minimum Arcing Times of a Fast Vacuum Circuit Breaker

2021 ◽  
Author(s):  
Chen Guan ◽  
Xiaofei Yao ◽  
Weidong Wang ◽  
Ran Zhang ◽  
Luyang Zhang ◽  
...  
Keyword(s):  
Short Circuit ◽  
Circuit Breaker ◽  
Vacuum Circuit Breaker

Protection Coordination of 33/11 kV Power Distribution Substation in Iraq

2021 ◽  
Vol 39 (5A) ◽  
pp. 723-737
Author(s):  
Yamur M. Obied ◽  
Thamir M. Abdul Wahhab
Keyword(s):  
Time Delay ◽  
Power System ◽  
Power Distribution ◽  
Software Package ◽  
Short Circuit ◽  
Distribution Network ◽  
Circuit Breaker ◽  
Short Circuit Current ◽  
Earth Fault ◽  
Current Characteristics

The coordination between protective devices is the process of determining the most appropriate timing of power interruption during abnormal conditions in the power system. The aim of this work is to coordinate the protection of the 33/11 kV power distribution substation in Iraq using the CYME 7.1 software package. In this paper overcurrent and earth fault relays are simulated in two cases, with time delay setting and instantaneous setting, to obtain the Time Current Characteristics (TCC) curves for each Circuit Breaker (CB) relay of Al-Karama substation (2×31.5 MVA, 33/11 kV) in Babil distribution network. The short circuit current at each CB is calculated and accordingly, the protection coordination for Al-Karama substation has been simulated. The TCC curves have been obtained in two cases for overcurrent and earth fault relays; in a case with time delay setting and in the case with the instantaneous setting. The setting takes into consideration the short circuit current at the furthest point of the longest outgoing feeder and the shortest outgoing feeder.

scholarly journals Development of a Method and Algorithm for Inhibiting an Automatic Transfer Switch of the Circuit Breaker for a Sustained Short-Circuit

2020 ◽  
Vol 220 ◽  
pp. 01011
Author(s):  
Igor Nikolaevich Fomin ◽  
Roman Pavlovich Belikov ◽  
Tatyana Anatolyevna Kudinova ◽  
Nailya Kamilevna Miftakhova
Keyword(s):  
Short Circuit ◽  
Circuit Breaker ◽  
Electrical Equipment ◽  
Ring Network ◽  
Circuit Breakers ◽  
Emergency Situations ◽  
Short Circuit Currents

Circuit breakers with automatic transfer switches (ATS) are designed in such a way that when the voltage disappears during a short-circuit (SC) in the ring network line, the ATS device is triggered. At the same time, its switch is turned on at short-circuit, then it is turned off with acceleration. Even a shortterm switching on of the automatic transfer switch for a sustained short-circuit leads to emergency situations [1,2]. The electrical equipment of the ring network spare line is exposed to high emergency short-circuit currents, and the consumers powered by the spare transformer are turned off. It is possible to minimize and eliminate the damages caused by the above mentioned cases by inhibiting the switching on of the circuitbreaker of the automatic transfer switch.

Analyzing the Impacts of Wind Generator on the Optimal Coordination of Overcurrent Relays

2012 ◽  
Vol 516-517 ◽  
pp. 1316-1321
Author(s):  
Ming Ta Yang ◽  
Jin Lung Guan ◽  
Jhy Cherng Gu
Keyword(s):  
Distribution Systems ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Original System ◽  
Wind Generator ◽  
Linear Programming Methods ◽  
Protection Strategies ◽  
Overcurrent Relays ◽  
Optimal Coordination ◽  
The Impact

Wind generator and distribution systems after interconnection would change the short circuit fault characteristics of the original system and may lead to protection relay malfunctions, and review of the protection coordination. It is necessary to research the impact of existing protection strategies for distribution systems after wind generator interconnection. Linear programming methods were adopted for this study to review the coordination problems among feeder circuit breaker, lateral circuit breaker, and power fuse after radial distribution systems and wind generator interconnections.

Sensor of Current or Magnetic Field Based on Magnetoresistance Effect in (La0.7Ca0.3)0.8Mn1.2O3 Manganite Film

2009 ◽  
Vol 154 ◽  
pp. 157-161 ◽  
Author(s):  
V.P. Dyakonov ◽  
S. Piechota ◽  
K. Piotrowski ◽  
A. Szewczyk ◽  
H. Szymczak ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Short Circuit ◽  
Operation Time ◽  
Electric Circuit ◽  
Current Sensor ◽  
Detectable Change ◽  
Magnetoresistance Effect ◽  
Manganite Film ◽  
Current Value ◽  
A Current

The main objective of the performed investigations was to enhance sensitivity of a current sensor to weak changes of magnetic field. New design of the sensor of current based on magnetoresistance effect – MRE (MRE = (RH - R0)/R0 , where RH is the resistance in magnetic field and R0 is the resistance without magnetic field) was developed. The sensor was produced in the form of an annular magnet with a gap, in which the (La0.7Sr0.3)0.8Мn1.2О3 manganite film possessing large negative MRE was inserted. Nominal current in a controllable electric circuit can change from a few tenths parts of ampere to a hundred of amperes. The limit detectable change of current value depends on the size of gap in the annular magnet. The operation time of sensor at current overload and short circuit is less than 0.3 sec. These magnetoresistors are thermally stable over the temperature range from (- 50 ° С) to (+ 50 ° С). Proposed sensors based on MRE can be applied in many electrical arrangements and devices.

scholarly journals Static Voltage Sharing Design of a Sextuple-Break 363 kV Vacuum Circuit Breaker

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2512 ◽  
Author(s):  
Xiao Yu ◽  
Fan Yang ◽  
Xing Li ◽  
Shaogui Ai ◽  
Yongning Huang ◽  
...  
Keyword(s):  
Electric Field ◽  
Circuit Simulation ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Normal Operation ◽  
Parallel Structure ◽  
Voltage Distribution ◽  
Fem Model ◽  
Vacuum Circuit Breaker ◽  
A Minor

A balanced voltage distribution for each break is required for normal operation of a multi-break vacuum circuit breaker (VCB) This paper presented a novel 363 kV/5000 A/63 kA sextuple-break VCB with a series-parallel structure. To determine the static voltage distribution of each break, a 3D finite element method (FEM) model was established to calculate the voltage distribution and the electric field of each break at the fully open state. Our results showed that the applied voltage was unevenly distributed at each break, and that the first break shared the most voltage, about 86.3%. The maximum electric field of the first break was 18.9 kV/mm, which contributed to the reduction of the breaking capacity. The distributed and stray capacitance parameters of the proposed structure were calculated based on the FEM model. According to the distributed capacitance parameters, the equivalent circuit simulation model of the static voltage distribution of this 363 kV VCB was established in PSCAD. Subsequently, the influence of the grading capacitor on the voltage distribution of each break was investigated, and the best value of the grading capacitors for the 363 kV sextuple-break VCB was confirmed to be 10 nF. Finally, the breaking tests of a single-phase unit was conducted both in a minor loop and a major loop. The 363 kV VCB prototype broke both the 63 kA and the 80 kA short circuit currents successfully, which confirmed the validity of the voltage sharing design.

Sign in / Sign up

Export Citation Format

Share Document