Water Compatibility and Scale Risk Evaluation by Integrating Scale Prediction of Fluid Modelling, Reservoir Simulation and Laboratory Coreflood Experiment for a Giant Oil Field in Offshore Abu Dhabi

2021 ◽  
Author(s):  
Yukito Nomura ◽  
Mariam Sultan Almarzooqi ◽  
Ken Makishima ◽  
Jon Tuck
Keyword(s):  
Reservoir Simulation ◽  
Water Injection ◽  
Oil Field ◽  
Mitigation Measures ◽  
Formation Water ◽  
Mixing Ratio ◽  
Field Scale ◽  
Reservoir Temperature ◽  
Injection Strategy ◽  
Sulphate Concentration

Abstract An offshore field is producing oil from multiple reservoirs with peripheral water injection scheme. Seawater is injected through a subsea network and wellhead towers located along the original reservoir edge. However, because its OWC has moved upward, wells from wellhead towers are too remote to inject seawater effectively, with some portion going to the aquifer rather than oil pool. Therefore, it is planned to migrate injection strategy from peripheral to mid-dip pattern. An expected risk is scaling by mixing incompatible seawater and formation water. Such risk and mitigation measures were evaluated. To achieve the objective, the following methodology was applied: 1. Scale modelling based on water chemical analysis. 2. Define scale risk envelope with three risk categories 3. Tracer dynamic reservoir simulation to track formation water, connate water, dump flood water, injection seawater and treated seawater. 4. Review the past field scale history data 5. Coreflood experiment to observe actual phenomena inside the reservoir with various parameters such as water mixing ratio, sulphate concentration, temperature and chemical inhibitor 6. Consolidate all study results, conclude field scale risk and impact of mitigation measures. Scale prediction modelling, verified by coreflood tests, found that mixing reservoir formation water and injection seawater causes a sulphate scale risk, with risk severity depending on mixing ratio and sulphate concentration. Reservoir temperature was also found to correlate strongly with scale risk. Therefore, each reservoir should have different water management strategy. Scale impact is limited in the shallower wide reservoir with cooler reservoir temperature. Such reservoir should therefore have mid-dip pattern water injection to avoid low water injection efficiency with possible scale inhibitor squeezing as a contingency option. On the other hand, deeper reservoir has higher risk of scaling due to its higher temperature, causing scale plugging easily in reservoir pores and production wells. For such reservoir, peripheral aquifer water injection, treated low-sulphate seawater with sulphate-removal system, or no water injection development concept should be selected. By using modelling and experiment to quantify the scale risk over a range of conditions, the field operator has identified opportunities to optimize the water injection strategy. The temperature dependence of the scale risk means, in principal, that different injection strategy for each reservoir can minimize flow assurance challenges and maximize return on investment in scale mitigation measures.

Solubility Of Common Oil Field Scales Of Injection Water And High–barium Concentration And High–salinity Formation Water

2012 ◽  
Author(s):  
Amer Badr Merdhah ◽  
Abu Azam Mohd Yassin
Keyword(s):  
Oil And Gas ◽  
High Salinity ◽  
Sea Water ◽  
Water Injection ◽  
Gas Production ◽  
Oil Field ◽  
Formation Water ◽  
Oil And Gas Production ◽  
Barium Concentration ◽  
Injection Water

Kerak pemendapan merupakan satu daripada masalah paling penting dan serius dalam sistem suntikan air. Kerak kadangkala mengehadkan atau menghalang penghasilan gas dan minyak melalui penyumbatan matrik atau perpecahan pembentukan minyak dan jeda yang berlubang. Makalah ini mengetengahkan kesimpulan pengukuran makmal bagi kerak terbentuk di dalam keterlarutan medan minyak biasa dalam sintetik air masin (pembentukan air dan air laut) bagi pembentukan air yang mengandungi barium dan kandungan garam yang tinggi pada suhu 40 hingga 90°C pada tekanan atmosfera. Keputusan uji kaji mengesahkan pola kebergantungan keterlarutan bagi kerak medan minyak biasa pada keadaan ini. Pada suhu yang lebih tinggi, kerak bagi CaCO3, CaSO4, dan SrSO4 meningkat manakala kerak BaSO4 menurun disebabkan oleh keterlarutan CaCO3, CaSO4, dan SrSO4 menurun dan keterlarutan BaSO4 meningkat dengan kenaikan suhu. Kata kunci: Masalah pengskalaan; skala keterlarutan; paras kandungan garam tinggi; logam barium tinggi Scale deposition is one of the most important and serious problems which water injection systems are generally engaged in. Scale sometimes limits or blocks oil and gas production by plugging the oil–producing formation matrix or fractures and the perforated intervals. This paper presents a summary of the laboratory measurements of the solubility of common oil field scales in synthetic brines (formation water and sea water) of high–barium and high–salinity formation waters at 40 to 90°C and atmospheric pressure. The experimental results confirm the general trend in solubility dependencies for common oil field scales at these conditions. At higher temperatures the deposition of CaCO3, CaSO4 and SrSO4 scale increases and the deposition of BaSO4 scale decreases since the solubilities of CaCO3, CaSO4 and SrSO4 scales decreases and the solubility of BaSO4 increases with increasing temperature. Key words: Scaling problems; solubility of scale; high salinity; high barium

Optimising Oil Field Net Present Value with Produced Water Salinities and Tracers

2021 ◽  
Author(s):  
Babalola Daramola
Keyword(s):  
Reservoir Simulation ◽  
Produced Water ◽  
Water Injection ◽  
Oil Production ◽  
Oil Field ◽  
Water Flooding ◽  
Water Salinity ◽  
History Match ◽  
Infill Drilling ◽  
Salinity Data

Abstract This paper presents case studies of how produced water salinity data was used to transform the performance of two oil producing fields in Nigeria. Produced water salinity data was used to improve Field B’s reservoir simulation history match, generate infill drilling targets, and reinstate Field C’s oil production. A reservoir simulation study was unable to history match the water cut in 3 production wells in Field B. Water salinity data enabled the asset team to estimate the arrival time of injected sea water at each production well in oil field B. This improved the reservoir simulation history match, increased model confidence, and validated the simulation model for the placement of infill drilling targets. The asset team also gained additional insight on the existing water flood performance, transformed the water flooding strategy, and added 9.6 MMSTB oil reserves. The asset team at Field C was unable to recover oil production from a well after it died suddenly. The team evaluated water salinity data, which suggested scale build up in the well, and completed a bottom-hole camera survey to prove the diagnosis. This justified a scale clean-out workover, and added 5000 barrels per day of oil production. A case study of how injection tracer data was used to characterise a water injection short circuit in Field D is also presented. Methods of using produced water salinity and injection tracer data to manage base production and add significant value to petroleum fields are presented. Produced water salinity and injection tracer data also simplify water injection connectivity evaluations, and can be used to justify test pipeline and test separator installation for data acquisition.

scholarly journals Chemical and biological compatibility of different injection waters with Zubair Formation Water of Upper Sand Member in Zubair Oil Field, South of Iraq

2021 ◽  
Vol 877 (1) ◽  
pp. 012013
Author(s):  
Inass Abdal Razaq Almallah ◽  
Fahad Al Najm ◽  
Zainb Ali Husain
Keyword(s):  
Water Samples ◽  
Water Injection ◽  
Oil Field ◽  
Water Flooding ◽  
Formation Damage ◽  
Formation Water ◽  
Chemical Compatibility ◽  
Weakly Alkaline ◽  
Weakly Acid ◽  
Biological Compatibility

Abstract Water injection by water flooding was used to enhance and increase oil production in Zubair oil field, southern Iraq. Physical-chemical and biological analysis of five water samples from different sources were collected to evaluate its compatibility with formation water using biological experiments and chemical compatibility simulation. The results show that injection water is classified weakly acidic-weakly alkaline and saline water, whereas surface water samples are considered weakly acid-weakly alkaline. The total dissolved solids results show brackish types accept for Formation water which classified weakly acid and Brine water. All the studied water samples contain bacteria colonies of Escherichia coli and Coliform expect for one sample, while Sulfate Reducing Bacteria was founded in all studied samples. Mathematical model of chemical compatibility between studied water samples and Zubair Formation water of the scale prediction model show that there are no needs for any inhibition treatments of all scales except for Geothite and Dolomite that should be treated before water injection. The biological compatibility experiments results show Formation damage about (61%) and (69%) in the studied core samples, while Bactria in water injection caused formation damage about (20%) and (51%).

scholarly journals Injection-production optimization of carbonate reservoir based on an inter-well connectivity model

2021 ◽  
pp. 014459872199465
Author(s):  
Yuhui Zhou ◽  
Sheng Lei ◽  
Xuebiao Du ◽  
Shichang Ju ◽  
Wei Li
Keyword(s):  
History Matching ◽  
Water Injection ◽  
Field Application ◽  
Carbonate Reservoir ◽  
Production Optimization ◽  
Oil Field ◽  
Carbonate Reservoirs ◽  
Utilization Rate ◽  
Production Volume ◽  
Connectivity Model

Carbonate reservoirs are highly heterogeneous. During waterflooding stage, the channeling phenomenon of displacing fluid in high-permeability layers easily leads to early water breakthrough and high water-cut with low recovery rate. To quantitatively characterize the inter-well connectivity parameters (including conductivity and connected volume), we developed an inter-well connectivity model based on the principle of inter-well connectivity and the geological data and development performance of carbonate reservoirs. Thus, the planar water injection allocation factors and water injection utilization rate of different layers can be obtained. In addition, when the proposed model is integrated with automatic history matching method and production optimization algorithm, the real-time oil and water production can be optimized and predicted. Field application demonstrates that adjusting injection parameters based on the model outputs results in a 1.5% increase in annual oil production, which offers significant guidance for the efficient development of similar oil reservoirs. In this study, the connectivity method was applied to multi-layer real reservoirs for the first time, and the injection and production volume of injection-production wells were repeatedly updated based on multiple iterations of water injection efficiency. The correctness of the method was verified by conceptual calculations and then applied to real reservoirs. So that the oil field can increase production in a short time, and has good application value.

Short-Term and Long-Term Aspects of Water Injection Strategy

2008 ◽  
Author(s):  
Bruno Alain Stenger ◽  
Abdulla Bakheet Al Katheeri ◽  
Hafez H. Hafez ◽  
Salem H. Al Kendi
Keyword(s):  
Water Injection ◽  
Short Term ◽  
Injection Strategy

Diagnostic Plots for Production Decline During the Transition of Oil Field Development From Depletion to Water Injection

2021 ◽  
Author(s):  
Vil Syrtlanov ◽  
Yury Golovatskiy ◽  
Ivan Ishimov
Keyword(s):  
Water Injection ◽  
Simulation Models ◽  
Oil Field ◽  
Production Data ◽  
Oil Reservoir ◽  
Field Development ◽  
Well Production ◽  
Diagnostic Plots ◽  
Oil Field Development ◽  
Analytical Approaches

Abstract In this paper the simplified way is proposed for predicting the dynamics of liquid production and estimating the parameters of the oil reservoir using diagnostic curves, which are a generalization of analytical approaches, partially compared with the results of calculations on 3D simulation models and with actual well production data.

Reservoir Simulation Modeling of the World's Largest Clastic Oil Field - The Greater Burgan Field, Kuwait

2014 ◽  
Author(s):  
E. Ma ◽  
S. Ryzhov ◽  
S. Gheorghiu ◽  
O. Hegazy ◽  
M. Banagale ◽  
...  
Keyword(s):  
Reservoir Simulation ◽  
Simulation Modeling ◽  
Oil Field

Nanotechnology Helps Decrease Pressure, Increase Injection in Offshore China Oil Field

2021 ◽  
Vol 73 (09) ◽  
pp. 58-59
Author(s):  
Chris Carpenter
Keyword(s):  
Water Injection ◽  
Injection Pressure ◽  
Gas Production ◽  
Oil Field ◽  
Water Flooding ◽  
Injection System ◽  
Bohai Bay ◽  
Reservoir Properties ◽  
Positive Effects ◽  
Offshore Technology

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper OTC 30407, “Case Study of Nanopolysilicon Materials’ Depressurization and Injection-Increasing Technology in Offshore Bohai Bay Oil Field KL21-1,” by Qing Feng, Nan Xiao Li, and Jun Zi Huang, China Oilfield Services, et al., prepared for the 2020 Offshore Technology Conference Asia, originally scheduled to be held in Kuala Lumpur, 2–6 November. The paper has not been peer reviewed. Copyright 2020 Offshore Technology Conference. Reproduced by permission. Nanotechnology offers creative approaches to solve problems of oil and gas production that also provide potential for pressure-decreasing application in oil fields. However, at the time of writing, successful pressure-decreasing nanotechnology has rarely been reported. The complete paper reports nanopolysilicon as a new depressurization and injection-increasing agent. The stability of nanopolysilicon was studied in the presence of various ions, including sodium (Na+), calcium (Ca2+), and magnesium (Mg2+). The study found that the addition of nanomaterials can improve porosity and permeability of porous media. Introduction More than 600 water-injection wells exist in Bohai Bay, China. Offshore Field KL21-1, developed by water-flooding, is confronted with the following challenges: - Rapid increase and reduction of water-injection pressure - Weak water-injection capacity of reservoir - Decline of oil production - Poor reservoir properties - Serious hydration and expansion effects of clay minerals To overcome injection difficulties in offshore fields, conventional acidizing measures usually are taken. But, after multiple cycles of acidification, the amount of soluble substances in the rock gradually decreases and injection performance is shortened. Through injection-performance experiments, it can be determined that the biological nanopolysilicon colloid has positive effects on pressure reduction and injection increase. Fluid-seepage-resistance decreases, the injection rate increases by 40%, and injection pressure decreases by 10%. Features of Biological Nanopolysilicon Systems The biological nanopolysilicon-injection system was composed of a bioemulsifier (CDL32), a biological dispersant (DS2), and a nanopolysilicon hydrophobic system (NP12). The bacterial strain of CDL32 was used to obtain the culture colloid of biological emulsifier at 37°C for 5 days. DS2 was made from biological emulsifier CDL32 and some industrial raw materials described in Table 1 of the complete paper. Nanopolysilicon hydrophobic system NP12 was composed of silicon dioxide particles. The hydrophobic nanopolysilicons selected in this project featured particle sizes of less than 100 nm. In the original samples, a floc of nanopolysilicon was fluffy and uniform. But, when wet, nanopolysilicon will self-aggregate and its particle size increases greatly. At the same time, nanopolysilicon features significant agglomeration in water. Because of its high interface energy, nanopolysilicon is easily agglomerated, as shown in Fig. 1.

Sign in / Sign up

Export Citation Format

Share Document