Engineering Geological and Petrological Characterization of Paleoweathered Rock in The K1/j2 Contact Zone in the Ordos Basin, China

2021 ◽  
Author(s):  
Tingen Zhu ◽  
wenping Li ◽  
Qiqing Wang ◽  
Yanbo Hu
Keyword(s):  
Mechanical Properties ◽  
Bulk Density ◽  
Contact Zone ◽  
Mutual Influence ◽  
Experimental Testing ◽  
Ordos Basin ◽  
Field Investigation ◽  
High Porosity ◽  
Quartz Content ◽  
Geological Processes

Abstract Various geological processes (mineral composition, structure, tectonics and weathering, etc.) affect the physical-mechanical properties of rock. Petrological and engineering geological characteristics of paleoweathered rock (PWR) from the K1/J2 contact zone are described in detail via field investigation and experimental testing. This PWR exhibits mainly sandy grains and mud structures, layered and massive strata, and calcareous and argillaceous cements; fissures are developed and often filled with argillaceous and detrital materials; 9 minerals and 7 oxides are present, and quartz is present in each sample. Long-term weathering results in a consistent bulk density and high porosity due to the transformation of primary minerals into secondary clay minerals, forming PWR that undergoes argillization in water. The axial point load strength (PLS) is the largest among the tested PLSs, followed by the diametral PLS, and the irregular PLS. The uniaxial compressive strength (UCS) varies widely, but the results are reliable. The mineralogical, physical and mechanical properties of the PWR are compared to predict one parameter from another and study their mutual influence. The PLS and UCS of the PWR are negatively correlated with the elastic mineral group (EMG) content, weathering alteration indexes, water content, and total porosity and positively correlated with the quartz content, brittle mineral group (BMG) content, bulk density, real density, and longitudinal wave velocity. The UCS and the PLS, axial (diametral) PLS and irregular PLS are positively correlated. These results provide a theoretical basis for physical and mechanical property prediction of PWR masses and rapid estimation of UCS in engineering.

Compositional and Structural Deficiencies Causing Failure of Local Fire Assaying Crucibles in Ghana

2020 ◽  
Vol 51 ◽  
pp. 57-70
Author(s):  
Yongdan Hou ◽  
Lemuel Gbologah ◽  
Derrick Boateng Asante ◽  
Parpah Senanu Kwawukume
Keyword(s):  
Field Investigation ◽  
Silica Content ◽  
High Alumina ◽  
High Porosity ◽  
Quartz Content ◽  
Structural Investigations ◽  
Mullite Phase ◽  
Free Silica ◽  
Basic Flux ◽  
Stable Performance

Locally produced crucibles in Ghana experience dimensional failures during fire assaying of ores, therefore, even with a higher cost, imported crucibles are still the most preferred choice by laboratories in Ghana because of the stable performance of up to three cycles. Assay crucibles of locally manufactured, imported and theoretically composed were sampled and analysed via reverse engineering to identify factors that are attributed to the failure during use. Field investigation and compositional, physical and structural investigations were carried out using XRD, water boiling and SEM-EDS analyses, respectively. The results indicated that failure of the local crucible can be attributed to low mullite phase in both content and planes, which could ease the crack development and enhance the thermal stability of the crucible; non converted quartz into cristobalite, which stabilises the volume expansion coefficient during the fire assaying cycles; excess quartz content and absence of alumina content weakened the corrosion resistance against attack from the basic flux of litharge; and high porosity, allowed penetration of molten charge into the structure of crucible, leading to the dissolution of free silica content into the charge and causing structural failure. To overcome such deficiencies, higher firing temperature (~1240 °C), extra soaking time, and blending of high alumina contained clay/minerals were suggested.

Tire Treadwear — A Comprehensive Evaluation of the Factors: Generic Type, Aspect Ratio, Tread Pattern, and Tread Composition Part IV: Laboratory Measurement of Mechanical Properties and Mechanical Actions of Tires Relating to Treadwear

1986 ◽  
Vol 14 (4) ◽  
pp. 264-291
Author(s):  
K. L. Oblizajek ◽  
A. G. Veith
Keyword(s):  
Mechanical Properties ◽  
Shear Stress ◽  
Contact Zone ◽  
Flexural Rigidity ◽  
Comprehensive Evaluation ◽  
Shear Stiffness ◽  
Shear Stresses ◽  
Lateral Shear ◽  
Band Bending ◽  
Tread Rubber

Abstract Treadwear is explained by specific mechanical properties and actions of tires. Rubber shear stresses in the contact zone between the tire and the road become large at large slip angles. When normal stresses are insufficient to prevent sliding at the rear of the footprint, wear occurs at a rate that depends on test severity. Two experimental approaches are described to relate treadwear to tire characteristics. The first uses transducers imbedded in a simulated road surface to obtain direct measurements of contact stresses on the loaded, freely-rolling, steered tires. The second approach is developed with the aid of a simple carcass, tread-band, tread-rubber tire model. Various tire structural configurations; characterized by carcass spring rate, edgewise flexural band stiffness, and tread rubber shear stiffness; are simulated and lateral shear stress response in the contact zone is determined. Tires featuring high band stiffness and low carcass stiffness generate lower lateral shear stress levels. Furthermore, coupling of tread-rubber stiffness and band flexural rigidity are important in determining level of shear stresses. Laboratory measurements with the described apparatus produced values of tread-band bending and carcass lateral stiffness for several tire constructions. Good correlation is shown between treadwear and a broad range of tire stiffness and test course severities.

scholarly journals Fabrication of Hybrid Nanofibers from Biopolymers and Poly (Vinyl Alcohol)/Poly (ε-Caprolactone) for Wound Dressing Applications

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2104
Author(s):  
Sibusiso Alven ◽  
Blessing Atim Aderibigbe
Keyword(s):  
Mechanical Properties ◽  
Wound Healing ◽  
Vinyl Alcohol ◽  
Wound Dressing ◽  
Chronic Wounds ◽  
Cellular Adhesion ◽  
Wound Dressings ◽  
Poly Vinyl Alcohol ◽  
High Porosity ◽  
Hybrid Nanofibers

The management of chronic wounds is challenging. The factors that impede wound healing include malnutrition, diseases (such as diabetes, cancer), and bacterial infection. Most of the presently utilized wound dressing materials suffer from severe limitations, including poor antibacterial and mechanical properties. Wound dressings formulated from the combination of biopolymers and synthetic polymers (i.e., poly (vinyl alcohol) or poly (ε-caprolactone) display interesting properties, including good biocompatibility, improved biodegradation, good mechanical properties and antimicrobial effects, promote tissue regeneration, etc. Formulation of these wound dressings via electrospinning technique is cost-effective, useful for uniform and continuous nanofibers with controllable pore structure, high porosity, excellent swelling capacity, good gaseous exchange, excellent cellular adhesion, and show a good capability to provide moisture and warmth environment for the accelerated wound healing process. Based on the above-mentioned outstanding properties of nanofibers and the unique properties of hybrid wound dressings prepared from poly (vinyl alcohol) and poly (ε-caprolactone), this review reports the in vitro and in vivo outcomes of the reported hybrid nanofibers.

scholarly journals Strategies to Reduce Porosity in Al-Mg WAAM Parts and Their Impact on Mechanical Properties

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 524
Author(s):  
Maider Arana ◽  
Eneko Ukar ◽  
Iker Rodriguez ◽  
Amaia Iturrioz ◽  
Pedro Alvarez
Keyword(s):  
Mechanical Properties ◽  
Gas Flow ◽  
Bottom Layer ◽  
Local Heat ◽  
High Porosity ◽  
Shielding Gas ◽  
Heat Accumulation ◽  
High Mechanical Property ◽  
Building Conditions ◽  
Static Tensile

With the advent of disruptive additive manufacturing (AM), there is an increasing interest and demand of high mechanical property aluminium parts built directly by these technologies. This has led to the need for continuous improvement of AM technologies and processes to obtain the best properties in aluminium samples and develop new alloys. This study has demonstrated that porosity can be reduced below 0.035% in area in Al-Mg samples manufactured by CMT-based WAAM with commercial filler metal wires by selecting the correct shielding gas, gas flow rate, and deposition strategy (hatching or circling). Three phase Ar+O2+N2O mixtures (Stargold®) are favourable when the hatching deposition strategy is applied leading to wall thickness around 6 mm. The application of circling strategy (torch movement with overlapped circles along the welding direction) enables the even build-up of layers with slightly thicker thickness (8 mm). In this case, Ar shielding gas can effectively reduce porosity if proper flow is provided through the torch. Reduced gas flows (lower than 30 Lmin) enhance porosity, especially in long tracks (longer than 90 mm) due to local heat accumulation. Surprisingly, rather high porosity levels (up to 2.86 area %) obtained in the worst conditions, had a reduced impact on the static tensile test mechanical properties, and yield stress over 110 MPa, tensile strength over 270 MPa, and elongation larger than 27% were achieved either for Ar circling, Ar hatching, or Stargold® hatching building conditions. In all cases anisotropy was lower than 11%, and this was reduced to 9% for the most appropriate shielding conditions. Current results show that due to the selected layer height and deposition parameters there was a complete re-melting of the previous layer and a thermal treatment on the prior bottom layer that refined the grain size removing the original dendritic and elongated structure. Under these conditions, the minimum reported anisotropy levels can be achieved.

Modeling the Large Deformation and Microstructure Evolution of Nonwoven Polymer Fiber Networks

2018 ◽  
Vol 86 (1) ◽  
Author(s):  
Mang Zhang ◽  
Yuli Chen ◽  
Fu-pen Chiang ◽  
Pelagia Irene Gouma ◽  
Lifeng Wang
Keyword(s):  
Mechanical Properties ◽  
Aspect Ratio ◽  
Mechanical Behavior ◽  
Large Deformation ◽  
Biological Tissues ◽  
High Porosity ◽  
Polymer Fiber ◽  
Fiber Networks ◽  
Fiber Aspect Ratio ◽  
Network Microstructure

The electrospinning process enables the fabrication of randomly distributed nonwoven polymer fiber networks with high surface area and high porosity, making them ideal candidates for multifunctional materials. The mechanics of nonwoven networks has been well established for elastic deformations. However, the mechanical properties of the polymer fibrous networks with large deformation are largely unexplored, while understanding their elastic and plastic mechanical properties at different fiber volume fractions, fiber aspect ratio, and constituent material properties is essential in the design of various polymer fibrous networks. In this paper, a representative volume element (RVE) based finite element model with long fibers is developed to emulate the randomly distributed nonwoven fibrous network microstructure, enabling us to systematically investigate the mechanics and large deformation behavior of random nonwoven networks. The results show that the network volume fraction, the fiber aspect ratio, and the fiber curliness have significant influences on the effective stiffness, effective yield strength, and the postyield behavior of the resulting fiber mats under both tension and shear loads. This study reveals the relation between the macroscopic mechanical behavior and the local randomly distributed network microstructure deformation mechanism of the nonwoven fiber network. The model presented here can also be applied to capture the mechanical behavior of other complex nonwoven network systems, like carbon nanotube networks, biological tissues, and artificial engineering networks.

scholarly journals Comparison of Mechanical Behavior and Acoustic Emission Characteristics of Three Thermally-Damaged Rocks

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2350 ◽  
Author(s):  
Jun Peng ◽  
Sheng-Qi Yang
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Mechanical Behavior ◽  
Thermal Damage ◽  
Strain Curve ◽  
Treatment Temperature ◽  
P Wave ◽  
High Temperature Treatment ◽  
High Porosity ◽  
Compression Tests

High temperature treatment has a significant influence on the mechanical behavior and the associated microcracking characteristic of rocks. A good understanding of the thermal damage effects on rock behavior is helpful for design and stability evaluation of engineering structures in the geothermal field. This paper studies the mechanical behavior and the acoustic emission (AE) characteristic of three typical rocks (i.e., sedimentary, metamorphic, and igneous), with an emphasis on how the difference in rock type (i.e., porosity and mineralogical composition) affects the rock behavior in response to thermal damage. Compression tests are carried out on rock specimens which are thermally damaged and AE monitoring is conducted during the compression tests. The mechanical properties including P-wave velocity, compressive strength, and Young’s modulus for the three rocks are found to generally show a decreasing trend as the temperature applied to the rock increases. However, these mechanical properties for quartz sandstone first increase to a certain extent and then decrease as the treatment temperature increases, which is mainly attributed to the high porosity of quartz sandstone. The results obtained from stress–strain curve, failure mode, and AE characteristic also show that the failure of quartz-rich rock (i.e., quartz sandstone and granite) is more brittle when compared with that of calcite-rich rock (i.e., marble). However, the ductility is enhanced to some extent as the treatment temperature increases for all the three examined rocks. Due to high brittleness of quartz sandstone and granite, more AE activities can be detected during loading and the recorded AE activities mostly accumulate when the stress approaches the peak strength, which is quite different from the results of marble.

scholarly journals Thermal insulation properties of green vacuum insulation panel using wood fiber as core material

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 3339-3351 ◽  
Author(s):  
Baowen Wang ◽  
Zhihui Li ◽  
Xinglai Qi ◽  
Nairong Chen ◽  
Qinzhi Zeng ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Bulk Density ◽  
Thermal Insulation ◽  
Wood Fiber ◽  
Core Material ◽  
High Porosity ◽  
Total Thermal Conductivity ◽  
Wood Fibers ◽  
Vacuum Insulation ◽  
Vacuum Insulation Panel

Wood fibers were prepared as core materials for a vacuum insulation panel (VIP) via a dry molding process. The morphology of the wood fibers and the microstructure, pore structure, transmittance, and thermal conductivity of the wood fiber VIP were tested. The results showed that the wood fibers had excellent thermal insulation properties and formed a porous structure by interweaving with one another. The optimum bulk density that led to a low-cost and highly thermally efficient wood fiber VIP was 180 kg/m3 to 200 kg/m3. The bulk density of the wood fiber VIP was 200 kg/m3, with a high porosity of 78%, a fine pore size of 112.8 μm, and a total pore volume of 7.0 cm3·g-1. The initial total thermal conductivity of the wood fiber VIP was 9.4 mW/(m·K) at 25 °C. The thermal conductivity of the VIP increased with increasing ambient temperature. These results were relatively good compared to the thermal insulation performance of current biomass VIPs, so the use of wood fiber as a VIP core material has broad application prospects.

scholarly journals EVALUATING THE SAWABILITY OF ROCKS BY CHAIN-SAW MACHINES USING THE PROMETHEE TECHNIQUE

2021 ◽  
Vol 36 (1) ◽  
pp. 25-36
Author(s):  
Reza Mikaeil ◽  
Akbar Esmaeilzadeh ◽  
Sara Aghaei ◽  
Sina Shaffiee Haghshenas ◽  
Amir Jafarpour ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Los Angeles ◽  
Production Rate ◽  
Physical And Mechanical Properties ◽  
Dimension Stone ◽  
Quartz Content ◽  
Los Angeles Abrasion ◽  
Production Values ◽  
Schmidt Hardness ◽  
Dimension Stone Quarry

One of the most significant factors in the estimation of dimension stone quarry cost is the production rate of rock cutting machines. Evaluating the production rate of chain-saw machines is a very significant and practical issue. In this research, it has been attempted to evaluate and select the suitable working-face for a quarry by examining the maximum production rate in the Dehbid and Shayan marble quarries. For this purpose, fi eld studies were carried out which included measuring operational characteristics of the chain-saw cutting machine, the production rate and sampling for laboratory tests from seven active case studies. Subsequently, the physical and mechanical properties of rocks including: Uniaxial Compressive Strength (UCS), Brazilian Tensile Strength (BTS), Los Angeles abrasion, quartz content, water absorption percentage, porosity, Schmidt hardness and grain size for all sample measurements were studied after transferring the samples to a rock-mechanics laboratory. Finally, the sawability of the quarried working-faces was evaluated using the PROMETHEE multi-criteria decision-making (MCDM) model according to the physical and mechanical properties. The results of the study indicated that the number 1 and 5 working-faces from the Dehbid and Shayan quarries are the most suitable working-faces in terms of production rate with the maximum recorded production values (4.95 and 3.1 m2 /h), and with net fl ow rates (2.67 and -0.36) respectively.

Mechanical Properties and Thermal Conductivity of Lightweight Clay Bricks Fabricated with a Powdered Marble Dust Additive

2018 ◽  
Vol 777 ◽  
pp. 465-470
Author(s):  
Sutas Janbuala ◽  
Mana Eambua ◽  
Arpapan Satayavibul ◽  
Watcharakhon Nethan
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Apparent Porosity ◽  
Clay Brick ◽  
Clay Bricks ◽  
Marble Dust

The objective of this study was to recycle powdered marble dust to improve mechanical properties and thermal conductivity of lightweight clay bricks. Varying amounts of powdered marble dust (10, 20, 30, and 40 vol.%) were added to a lightweight clay brick at the firing temperatures of 900, 1000, and 1100 °C. When higher quantities of powdered marble dust were added, the values of porosity and water absorption increased while those of thermal conductivity and bulk density decreased. The decrease in apparent porosity and water absorption were also affected by the increase in firing temperature. The most desirable properties of the clay bricks were obtained for the powdered marble dust content of 40 vol.% and firing temperature 900 °C: bulk density of 1.20 g/cm3, compressive strength 9.2 MPa, thermal conductivity 0.32 W/m.K, and water absorption 22.5%.

Sign in / Sign up

Export Citation Format

Share Document