scholarly journals Preliminary Study of the Mechanical Properties of Hybrid Fibres Reinforced Unsaturated Polyester Composites

2021 ◽  
Vol 32 (3) ◽  
pp. 45-59
Author(s):  
Chek Shin Tan ◽  
◽  
Ming Yeng Chan ◽  
Seong Chun Koay ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Testing ◽  
Fibre Orientation ◽  
Fibre Composite ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Elongation At Break ◽  
Corn Husk ◽  
Hybrid Fibre ◽  
Polyester Composite

This research project investigates the mechanical properties of the corn husk fibre reinforced unsaturated polyester composite (CHFPC) and hybrid fibre (corn husk/flax) reinforced unsaturated polyester composite (HFPC) at different fibre orientations. The tensile and flexural properties of CHFPC and HFPC were manipulated by the different degrees of fibre orientations of 0°, 45°, and 90°. Both CHFPC and HFPC with 0° of fibre orientation had the highest tensile strength and flexural strength. Moreover, the tensile and flexural modulus of specimens with 0° orientation had the highest result compared to 45° and 90° orientations. However, for the elongation at break during tensile testing, 0° orientation had the highest strain, more than unsaturated polyester (UPR) and other composites. The tensile and flexural strengths of HFPC specimens with 0° fibre orientation were higher than that of CHFPC. Besides, the tensile modulus and flexural modulus of HFPC also increased as compared to CHFPC. The elongation at break of HFPC for tensile testing had the highest strain compared to CHFPC. The results showed that the mechanical properties of the hybrid fibre composite performed better compared to the single fibre composite. Moreover, the corn husk fibre (CHF) and flax fibre (FF) acted as reinforcements to enhance the mechanical properties of the UPR composites.

Mechanical properties of polyester/corn husk fibre composite produced using vacuum infusion technique

2021 ◽  
Vol 29 (9_suppl) ◽  
pp. S1532-S1540
Author(s):  
Shibly Shadik Mir Md ◽  
Ming Yeng Chan ◽  
Seong Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Fibre Composite ◽  
Alkali Treatment ◽  
Flexural Modulus ◽  
Fibre Length ◽  
Flexural Properties ◽  
Vacuum Infusion ◽  
Corn Husk ◽  
Plastic Composite ◽  
Polyester Composites

Issues pertaining to deforestation, environmental pollution and natural wastes are increasing day by day. These issues can be resolved by introducing a new composite material, in which natural waste is used as fibre and as a replacement of wood plastic composite. The different lengths (3, 6 and 9 cm) of corn husk fibre filled polyester composites were produced using the vacuum infusion method. Several mechanical properties of these polyester composites, such as tensile and flexural properties, were evaluated. The results revealed that both the tensile and flexural properties of polyester composites increased with increment of corn husk fibre length from 3 to 6 cm. However, the results decreased for 9 cm of fibre length filled composites. Similar trends were recorded after alkali treatment of the corn husk fibre filled polyester composites. The alkali treatment with sodium hydroxide had improved the tensile strength (33%), Young’s modulus (23%), elongation (14%), flexural strength (42%) and flexural modulus (8.5%) of the polyester/corn husk fibre composites with 6 cm of fibre length by enhancing the mechanical interlocking bonding between treated corn husk fibres and polyester.

A Study of Some Mechanical and Physical Properties for Palm Fiber/Polyester Composite

2020 ◽  
Vol 38 (3B) ◽  
pp. 104-114
Author(s):  
Samah M. Hussein
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Dielectric Constant ◽  
Date Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Dielectric Strength ◽  
Palm Fiber ◽  
Mechanical And Physical Properties ◽  
Polyester Composite

This research has been done by reinforcing the matrix (unsaturated polyester) resin with natural material (date palm fiber (DPF)). The fibers were exposure to alkali treatment before reinforcement. The samples have been prepared by using hand lay-up technique with fiber volume fraction of (10%, 20% and 30%). After preparation of the mechanical and physical properties have been studied such as, compression, flexural, impact strength, thermal conductivity, Dielectric constant and dielectric strength. The polyester composite reinforced with date palm fiber at volume fraction (10% and 20%) has good mechanical properties rather than pure unsaturated polyester material, while the composite reinforced with 30% Vf present poor mechanical properties. Thermal conductivity results indicated insulator composite behavior. The effect of present fiber polar group induces of decreasing in dielectric strength, and increasing dielectric constant. The reinforcement composite 20% Vf showed the best results in mechanical, thermal and electrical properties.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

Hybrid silica micro and PDDA/nanoparticles-reinforced carbon fibre composites

2016 ◽  
Vol 51 (6) ◽  
pp. 783-795 ◽  
Author(s):  
Júlio C Santos ◽  
Luciano MG Vieira ◽  
Túlio H Panzera ◽  
André L Christoforo ◽  
Marco A Schiavon ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fibre ◽  
Silica Nanoparticles ◽  
Fibre Composite ◽  
Flexural Modulus ◽  
Specific Chemical ◽  
Diallyldimethylammonium Chloride ◽  
Fibre Composites ◽  
Carbon Fibre Composites ◽  
Hybrid Carbon

The work describes the manufacturing and testing of novel hybrid epoxy/carbon fibre composites with silica micro and poly-diallyldimethylammonium chloride-functionalised nanoparticles. A specific chemical dispersion procedure was applied using the poly-diallyldimethylammonium chloride to avoid clustering of the silica nanoparticles. The influence of the various manufacturing parameters, particles loading, and mechanical properties of the different phases has been investigated with a rigorous Design of Experiment technique based on a full factorial design (2131). Poly-diallyldimethylammonium chloride-functionalised silica nanoparticles were able to provide a homogenous dispersion, with a decrease of the apparent density and enhancement of the mechanical properties in the hybrid carbon fibre composites. Compared to undispersed carbon fibre composite laminates, the use of 2 wt% functionalised nanoparticles permitted to increase the flexural modulus by 47% and the flexural strength by 15%. The hybrid carbon fibre composites showed also an increase of the tensile modulus (9%) and tensile strength (5.6%).

The Effect of Yarn Linear Density on Mechanical Properties of Plain Woven Kenaf Reinforced Unsaturated Polyester Composite

2013 ◽  
Vol 465-466 ◽  
pp. 962-966 ◽  
Author(s):  
Mohd Pahmi bin Saiman ◽  
Mohd Saidin Bin Wahab ◽  
Mat Uzir Wahit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Linear Density ◽  
Unsaturated Polyester ◽  
Composite Panel ◽  
Composite Yarn ◽  
Polyester Composite ◽  
The Impact ◽  
Woven Kenaf

To produce a good quality of dry fabric for reinforced material in a natural-based polymer composite, yarn linear density should be in consideration. A woven kenaf dry fabric with three different linear densities of 276tex, 413.4tex and 759tex were produced. The fabrics with different linear densities were been optimize with the assistance of WiseTex software. The optimized dry fabrics were infused with unsaturated polyester to produce composite panel using vacuum infusion process. The composites properties were tested on the tensile strength, flexural strength and the impact strength. The result shows that the mechanical properties of the composite increased when the yarn linear densities increased.

scholarly journals Influence of kaolin filler on the mechanical properties of Luffa cylindrica/ polyester composite

2021 ◽  
Author(s):  
Aliyu Yaro ◽  
Laminu Kuburi ◽  
Musa Abiodun Moshood
Keyword(s):  
Mechanical Properties ◽  
Polyester Resin ◽  
Unsaturated Polyester ◽  
Low Cost ◽  
Microstructural Analysis ◽  
Polymeric Materials ◽  
Weight Fraction ◽  
Industrial Applications ◽  
Luffa Cylindrica ◽  
Polyester Composite

Abstract Polymeric materials are used in different industrial applications because they retain good environmental properties, low-cost, and easy to produce compared to conventional materials. This study investigated the effect of adding kaolin micro-filler (KF) on the mechanical properties of Luffa Fiber (LCF) reinforced polyester resin. Luffa cylindrica fiber treated with 5% NaOH, varied in weight fraction (5, 10, and 15%wt) was used to reinforce unsaturated polyester resin using hand lay-up method, whereas for the hybrid composite kaolin filler were kept constant at 6wt% fraction while the fibers varied as in the mono-reinforced composite. The samples were machined for mechanical and microstructural analysis. Analysis of the result revealed that the addition of kaolin has enhanced greatly the mechanical properties of Luffa-fibre based composites. The result reveal of the microstructure analysis, shows that there is an improvement in fiber-matrix adhesion.

scholarly journals Effects of Irradiation by UV- Acceleration on Mechanical Properties of Polymer Blends (Polyester: Starch)

2018 ◽  
Vol 21 (1) ◽  
pp. 147 ◽  
Author(s):  
Sihama I. Salih ◽  
Qahtan A. Hamad ◽  
Safaa N. Abdul Jabbar ◽  
Najat H. Sabit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Polymer Blends ◽  
Modulus Of Elasticity ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Weight Ratio ◽  
Weight Fraction ◽  
Elongation Percentage

This work covers mixing of unsaturated polyester (un- polyester) with starch powders as polymer blends and study the effects of irradiation by UV-acceleration on mechanical properties of its. The unsaturated polyester was mixing by starch powders at particle size less than (45 µm) at selected weight fraction of (0, 0.5, 1, 1.5, 2, 2.5 and 3%). These properties involve ultimate tensile strength, modulus of elasticity, elongation percentage, flexural modulus, flexural strength, fracture toughness, impact strength and hardness. The results illustrate decrease in the ultimate tensile strength at and elongation percentage, while increasing modulus of elasticity, with increasing the weight ratio of starch powder to 3 % weight fraction, whereas the maximum value of hardness and flexural, impact properties happened at 1 % weight fraction for types of polymer blends.

The Effect of Fiber Size on the Mechanical Properties of Bertam/Unsaturated Polyester Composites

2015 ◽  
Vol 761 ◽  
pp. 52-56
Author(s):  
M.H. Norhidayah ◽  
Arep Hambali ◽  
M.Y. Yuhazri
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Unsaturated Polyester ◽  
Flexural Modulus ◽  
Flexural Properties ◽  
Fiber Size ◽  
Polyester Composites

The aim of this paper was the effects of different fiber size on tensile and flexural properties. Preparation of thermoset unsaturated polyester reinforced with particle Bertam (Eugeissona tristis) was done by hand layout method. Bertam/polyester composites containing Bertam fiber of different sizes, i.e., 15, 120 and 284 μm were prepared. For each composite, eight specimens were tested to evaluate the mechanical properties. It was found that composite reinforced with Bertam having the shortest fiber length, i.e, 15 μm showed the highest tensile and flexural modulus, which were 204.14 MPa and 1826.78 MPa, respectively.

scholarly journals Mechanical properties of coconut trunk particle/polyester composite based on alkali treatment

2020 ◽  
Vol 29 ◽  
pp. 2633366X2093589
Author(s):  
Van-Tho Hoang ◽  
Thanh-Nhut Pham ◽  
Young-Jin Yum
Keyword(s):  
Mechanical Properties ◽  
Surface Modification ◽  
Polyester Resin ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Unsaturated Polyester ◽  
Test Results ◽  
Coconut Tree ◽  
Lignocellulosic Fiber ◽  
Polyester Composite

Coir is a well-known natural fiber extracted from the husk of a coconut tree. In polymer composite materials, the ultimate performance of coir has been shown using surface modification methods. Among them, sodium hydroxide (NaOH) is a comparative and efficient solution used for surface treatment of lignocellulosic fiber. In contrast to coir, coconut timber, a hardwood that dominates the weight of the coconut tree, has not been appropriately considered for use in polymer composites. Therefore, in this article, coconut trunk particle/unsaturated polyester resin composites were experimentally investigated. As a pioneering study, a large range of NaOH concentrations from 2 wt% to 10 wt% (with an interval of 2 wt%) was utilized to treat the surface of the filler. Finally, 4 wt% alkali solution was found as the best content for surface modification based on the mechanical properties of the composite, including those determined by tensile, flexural, and impact test results.

Sign in / Sign up

Export Citation Format

Share Document