Processing and Analysis of Experimental Data for the Impact Toughness of the Steel Quality J55 API 5CT Using Design Expert Software

2017 ◽  
Author(s):  
Malush Mjaku
Keyword(s):  
Experimental Data ◽  
Impact Toughness ◽  
Design Expert ◽  
Steel Quality ◽  
The Impact

Modification of ED-20 epoxy resin with polyvinyl formal ethylal

2020 ◽  
pp. 56-58
Author(s):  
N. V. Kostromina ◽  
Yu. V. Olikhova ◽  
Khlaing Zo U ◽  
V. S. Osipchik ◽  
T. P. Kravchenko
Keyword(s):  
Experimental Data ◽  
Impact Toughness ◽  
Epoxy Resin ◽  
Epoxy Resins ◽  
Domestic Technology ◽  
Polyvinyl Formal ◽  
The Impact

One of the methods for increasing the impact toughness of materials based on epoxy resins is modification with thermoplastics. The paper presents experimental data on the effect of polyvinyl formal ethylal (Vinyfl ex) and various curing modes on the toughness of compositions based on ED-20. The mechanism for modifying ED-20 with Vinyflex was analyzed. The data obtained are necessary for the development of domestic technology for the production of impact-resistant plastics.

scholarly journals Tempforming as an Advanced Processing Method for Carbon Steels

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1566
Author(s):  
Anastasiya Dolzhenko ◽  
Rustam Kaibyshev ◽  
Andrey Belyakov
Keyword(s):  
Impact Toughness ◽  
Crack Propagation ◽  
Large Strain ◽  
High Strength ◽  
Close Relation ◽  
Carbon Steels ◽  
Processing Method ◽  
Propagation Mode ◽  
Displacement Curve ◽  
The Impact

The microstructural mechanisms providing delamination toughness in high-strength low-alloyed steels are briefly reviewed. Thermo-mechanical processing methods improving both the strength and impact toughness are described, with a close relation to the microstructures and textures developed. The effect of processing conditions on the microstructure evolution in steels with different carbon content is discussed. Particular attention is paid to tempforming treatment, which has been recently introduced as a promising processing method for high-strength low-alloyed steel semi-products with beneficial combination of strength and impact toughness. Tempforming consists of large strain warm rolling following tempering. In contrast to ausforming, the steels subjected to tempforming may exhibit an unusual increase in the impact toughness with a decrease in test temperature below room temperature. This phenomenon is attributed to the notch blunting owing to easy splitting (delamination) crosswise to the principle crack propagation. The relationships between the crack propagation mode, the delamination fracture, and the load-displacement curve are presented and discussed. Further perspectives of tempforming applications and promising research directions are outlined.

Mechanical Properties of Equal-Channel Angular Extrusion-Processed Al-20Zn Alloy

2012 ◽  
Vol 445 ◽  
pp. 195-200
Author(s):  
Murat Aydin ◽  
Yakup Heyal
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Equal Channel Angular Extrusion ◽  
Considerable Change ◽  
Fatigue Properties ◽  
Dendritic Microstructure ◽  
Two Phase ◽  
Angular Extrusion ◽  
Alloy Increase ◽  
The Impact

The mechanical properties mainly tensile properties, impact toughness and high-cycle fatigue properties, of two-phase Al-20Zn alloy subjected to severe plastic deformation (SPD) via equal-channel angular extrusion (ECAE) using route A up to 2 passes were studied. The ECAE almost completely eliminated as-cast dendritic microstructure including casting defects such as micro porosities. A refined microstructure consisting of elongated micro constituents, α and α+η eutectic phases, formed after ECAE via route A. As a result of this microstructural change, mechanical properties mainly the impact toughness and fatigue performance of the as-cast Al-20Zn alloy increased significantly through the ECAE. The rates of increase in fatigue endurance limit are approximately 74 % after one pass and 89 % after two passes while the increase in impact toughness is 122 %. Also the yield and tensile strengths of the alloy increase with ECAE. However, no considerable change occurred in hardness and percentage elongation of the alloy. It was also observed that the ECAE changed the nature of the fatigue fracture characteristics of the as-cast Al-20Zn alloy.

SOME CHARACTERISTICS OF THE COMPOUND MULTIPLICITY IN HIGH-ENERGY NUCLEUS–NUCLEUS INTERACTIONS

2011 ◽  
Vol 20 (08) ◽  
pp. 1735-1754 ◽  
Author(s):  
M. MOHERY ◽  
M. ARAFA
Keyword(s):  
Experimental Data ◽  
Impact Parameter ◽  
Mass Number ◽  
Multiplicity Distribution ◽  
High Energy ◽  
Projectile Nucleus ◽  
Target Mass ◽  
Compound Multiplicity ◽  
Multiplicity Distributions ◽  
The Impact

The present paper deals with the interactions of 22 Ne and 28 Si nuclei at (4.1–4.5)A GeV /c with emulsion. Some characteristics of the compound multiplicity nc given by the sum of the number of shower particles ns and grey particles ng have been investigated. The present experimental data are compared with the corresponding ones calculated according to modified cascade evaporation model (MCEM). The results reveal that the compound multiplicity distributions for these two reactions are consistent with the corresponding ones of MCEM data. It can also be seen that the peak of these distributions shifts towards a higher value of nc with increasing projectile mass. It may further be seen that the compound multiplicity distributions becomes broader with increasing target size and its width increases with the size of the projectile nucleus. In addition, it has been found that the MCEM can describe the compound multiplicity characteristics of the different projectile, target and the correlation between different emitted particles. The values of average compound multiplicity increase with increasing mass of the projectile. Furthermore, it is observed that while the value of 〈nc〉 depends on the mass number of the projectile Ap and the target mass number At, the value of the ratio 〈nc〉/D(nc) seems to be independent of Ap and At. The impact parameter is found to affect the shape of the compound multiplicity distribution. Finally, the dependence of the average compound multiplicity on the numbers of grey and black particles, and the sum of them, is obvious. The values of the slope have been found to be independent of the projectile nucleus.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Effects of oxygen content on microstructure and impact toughness of high heat input flux-cored wire weld metals

2018 ◽  
Vol 115 (4) ◽  
pp. 410
Author(s):  
Fengyu Song ◽  
Yanmei Li ◽  
Ping Wang ◽  
Fuxian Zhu
Keyword(s):  
Grain Size ◽  
Impact Toughness ◽  
Weld Metal ◽  
Oxygen Content ◽  
Heat Input ◽  
High Heat ◽  
Cored Wire ◽  
Weld Metals ◽  
High Heat Input ◽  
The Impact

Three weld metals with different oxygen contents were developed. The influence of oxygen contents on the microstructure and impact toughness of weld metal was investigated through high heat input welding tests. The results showed that a large number of fine inclusions were formed and distributed randomly in the weld metal with oxygen content of 500 ppm under the heat input condition of 341 kJ/cm. Substantial cross interlocked acicular ferritic grains were induced to generate in the vicinity of the inclusions, primarily leading to the high impact toughness at low temperature for the weld metal. With the increase of oxygen content, the number of fine inclusions distributed in the weld metal increased and the grain size of intragranular acicular ferrites decreased, which enhanced the impact toughness of the weld metal. Nevertheless, a further increase of oxygen content would contribute to a great diminution of the austenitic grain size. Following that the fraction of grain boundary and the start temperature of transformation increased, which facilitated the abundant formation of pro-eutectoid ferrites and resulted in a deteriorative impact toughness of the weld metal.

The penetration and ricochet of ogive-nosed rigid projectiles obliquely impacting metallic targets

2021 ◽  
pp. 204141962110377
Author(s):  
Yaniv Vayig ◽  
Zvi Rosenberg
Keyword(s):  
Experimental Data ◽  
Numerical Simulations ◽  
Dynamic Pressure ◽  
Oblique Impacts ◽  
Simulation Results ◽  
The Impact ◽  
Penetration Depths ◽  
Resistance To Penetration ◽  
Good Agreement

A large number of 3D numerical simulations were performed in order to follow the trajectory changes of rigid CRH3 ogive-nosed projectiles, impacting semi-infinite metallic targets at various obliquities. These trajectory changes are shown to be related to the threshold ricochet angles of the projectile/target pairs. These threshold angles are the impact obliquities where the projectiles end up moving in a path parallel to the target’s face. They were found to depend on a non-dimensional entity which is equal to the ratio between the target’s resistance to penetration and the dynamic pressure exerted by the projectile upon impact. Good agreement was obtained by comparing simulation results for these trajectory changes with experimental data from several published works. In addition, numerically-based relations were derived for the penetration depths of these ogive-nosed projectiles at oblique impacts, which are shown to agree with the simulation results.

Ozone Production With Plasma Discharge: Comparisons Between Activated Air and Activated Fuel/Air Mixture

2021 ◽  
Author(s):  
Ghazanfar Mehdi ◽  
Maria Grazia De Giorgi ◽  
Donato Fontanarosa ◽  
Sara Bonuso ◽  
Antonio Ficarella
Keyword(s):  
Experimental Data ◽  
Plasma Chemistry ◽  
Kinetic Scheme ◽  
Plasma Discharge ◽  
Chemical Kinetic ◽  
Ozone Production ◽  
Air Plasma ◽  
Flammability Limits ◽  
Combustion Enhancement ◽  
The Impact

Abstract This study focused on the comparative analysis about the production of ozone and active radicals in presence of nanopulsed plasma discharge on air and on fuel/air mixture to investigate its effect on combustion enhancement. This analysis is based on numerical modeling of air and methane/air plasma discharge with different repetition rates (100 Hz, 1000 Hz and 10000 Hz). To this purpose, a two-step approach has been proposed based on two different chemistry solvers: a 0-D plasma chemistry solver (ZDPlasKin toolbox) and a combustion chemistry solver (CHEMKIN software suite). Consequently, a comprehensive chemical kinetic scheme was generated including both plasma excitation reactions and gas phase reactions. Validation of air and methane/air mechanisms was performed with experimental data. Kinetic models of both air and methane/air provides good fitting with experimental data of O atom generation and decay process. ZDPlasKin results were introduced in CHEMKIN in order to analyze combustion enhancement. It was found that the concentrations of O3 and O atom in air are higher than the methane/air activation. However, during the air activation peak concentration of ozone was significantly increased with repetition rates and maximum was observed at 10000 Hz. Furthermore, ignition timings and flammability limits were also improved with air and methane/air activation but the impact of methane/air activation was comparatively higher.

Sign in / Sign up

Export Citation Format

Share Document