scholarly journals Структурные, оптические и термоэлектрические свойства тонких ZnO:Al пленок, полученных атомно-слоевым осаждением

2019 ◽  
Vol 61 (10) ◽  
pp. 1941
Author(s):  
И.А. Тамбасов ◽  
М.Н. Волочаев ◽  
А.С. Воронин ◽  
Н.П. Евсевская ◽  
А.Н. Масюгин ◽  
...  
Keyword(s):  
Power Factor ◽  
Optical Band Gap ◽  
Atomic Layer ◽  
Root Mean Square Roughness ◽  
X Ray Diffraction ◽  
Absorption Coefficients ◽  
Aluminum Oxides ◽  
X Ray ◽  
Layer Deposition ◽  
Aluminum Doped Zinc Oxide

Thin films of aluminum doped zinc oxide were grown using atomic layer deposition at a temperature of 200 ° C. Using X-ray diffraction, it was found that thin ZnO: Al films have peaks from the (100), (002), (110) and (201) planes of the hexagonal ZnO phase. The (101) and (102) planes were also detected using electron diffraction. Thin ZnO: Al films grow smooth with a root-mean-square roughness of Rq of 0.33 nm and characteristic nanocrystallite sizes of ~ 70 and ~ 15 nm without additional phases associated with aluminum or aluminum oxides. The transmission at a wavelength of 550 nm, taking into account the substrate, was ~ 96%. The refractive indices and absorption coefficients of thin ZnO: Al films in the wavelength range of 250–900 nm were found. The maximum values ​​for the refractive and absorption coefficients were 2.09 at a wavelength of 335 nm and 0.39 at a wavelength of 295 nm, respectively. The optical band gap was 3.56 eV. The resistivity, the Seebeck coefficient and the power factor of thin ZnO: Al films were ~ 1.02 · 10-3 Ohm · cm, ~ - 60 μV / K and 340 μW · m-1 · K-2 at room temperature, respectively. The maximum power factor reached 620 μW · m-1 · K-2 at a temperature of 200 ° C.

scholarly journals Synthesis of indium oxi-sulfide films by atomic layer deposition: The essential role of plasma enhancement

2013 ◽  
Vol 4 ◽  
pp. 750-757 ◽  
Author(s):  
Cathy Bugot ◽  
Nathanaëlle Schneider ◽  
Daniel Lincot ◽  
Frédérique Donsanti
Keyword(s):  
Atomic Layer Deposition ◽  
Optical Band Gap ◽  
Atomic Layer ◽  
X Ray Diffraction ◽  
Structural And Optical Properties ◽  
Growth Cycles ◽  
X Ray ◽  
Layer Deposition ◽  
Plasma Enhancement

This paper describes the atomic layer deposition of In2(S,O)3 films by using In(acac)3 (acac = acetylacetonate), H2S and either H2O or O2 plasma as oxygen sources. First, the growth of pure In2S3 films was studied in order to better understand the influence of the oxygen pulses. X-Ray diffraction measurements, optical analysis and energy dispersive X-ray spectroscopy were performed to characterize the samples. When H2O was used as the oxygen source, the films have structural and optical properties, and the atomic composition of pure In2S3. No pure In2O3 films could be grown by using H2O or O2 plasma. However, In2(S,O)3 films could be successfully grown by using O2 plasma as oxygen source at a deposition temperature of T = 160 °C, because of an exchange reaction between S and O atoms. By adjusting the number of In2O3 growth cycles in relation to the number of In2S3 growth cycles, the optical band gap of the resulting thin films could be tuned.

Depositing High-Performance Conductive Thin Films by Using Atomic Layer Deposition

2015 ◽  
Vol 764-765 ◽  
pp. 138-142 ◽  
Author(s):  
Fa Ta Tsai ◽  
Hsi Ting Hou ◽  
Ching Kong Chao ◽  
Rwei Ching Chang
Keyword(s):  
Thin Films ◽  
Atomic Layer Deposition ◽  
High Performance ◽  
Atomic Layer ◽  
Electric Properties ◽  
X Ray Diffraction ◽  
Layer Deposition ◽  
Azo Thin Film ◽  
Aluminum Doped Zinc Oxide ◽  
Conductive Thin Films

This work characterizes the mechanical and opto-electric properties of Aluminum-doped zinc oxide (AZO) thin films deposited by atomic layer deposition (ALD), where various depositing temperature, 100, 125, 150, 175, and 200 °C are considered. The transmittance, microstructure, electric resistivity, adhesion, hardness, and Young’s modulus of the deposited thin films are tested by using spectrophotometer, X-ray diffraction, Hall effect analyzer, micro scratch, and nanoindentation, respectively. The results show that the AZO thin film deposited at 200 °C behaves the best electric properties, where its resistance, Carrier Concentration and mobility reach 4.3×10-4 Ωcm, 2.4×1020 cm-3, and 60.4 cm2V-1s-1, respectively. Furthermore, microstructure of the AZO films deposited by ALD is much better than those deposited by sputtering.

Ex-situ X-ray diffraction analysis of electrode strain at TiO2 atomic layer deposition/α-MoO3 interface in a novel aqueous potassium ion battery

2016 ◽  
Vol 316 ◽  
pp. 160-169 ◽  
Author(s):  
Nicholas David Schuppert ◽  
Santanu Mukherjee ◽  
Alex M. Bates ◽  
Eun-Jin Son ◽  
Moon Jong Choi ◽  
...  
Keyword(s):  
Atomic Layer Deposition ◽  
Diffraction Analysis ◽  
Atomic Layer ◽  
Potassium Ion ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
X Ray ◽  
Layer Deposition

scholarly journals Structure-Dependent Mechanical Properties of ALD-Grown Nanocrystalline BiFeO3Multiferroics

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Anna Majtyka ◽  
Anna Nowak ◽  
Benoît Marchand ◽  
Dariusz Chrobak ◽  
Mikko Ritala ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Photoelectron Spectroscopy ◽  
Present Report ◽  
Structural Evolution ◽  
Atomic Layer ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Layer Deposition ◽  
Pertinent Information

The present paper pertains to mechanical properties and structure of nanocrystalline multiferroic BeFiO3(BFO) thin films, grown by atomic layer deposition (ALD) on the Si/SiO2/Pt substrate. The usage of sharp-tip-nanoindentation and multiple techniques of structure examination, namely, grazing incidence X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, and energy dispersive X-ray spectrometry, enabled us to detect changes in elastic properties(95 GPa≤E≤118 GPa)and hardness(4.50 GPa≤H≤7.96 GPa)of BFO after stages of annealing and observe their relation to the material’s structural evolution. Our experiments point towards an increase in structural homogeneity of the samples annealed for a longer time. To our best knowledge, the present report constitutes the first disclosure of nanoindentation mechanical characteristics of ALD-fabricated BeFiO3, providing a new insight into the phenomena that accompany structure formation and development of nanocrystalline multiferroics. We believe that our systematic characterization of the BFO layers carried out at consecutive stages of their deposition provides pertinent information which is needed to control and optimize its ALD fabrication.

Electrical and Structural Properties of Ruthenium Film Grown by Atomic Layer Deposition Using Liquid-Phase Ru(CO)3(C6H8) Precursor

2007 ◽  
Vol 990 ◽  
Author(s):  
Sung-Hoon Chung ◽  
Vladislav Vasilyev ◽  
Evgeni Gorokhov ◽  
Yong-Won Song ◽  
Hyuk-Kyoo Jang
Keyword(s):  
Liquid Phase ◽  
Atomic Layer Deposition ◽  
Annealing Temperature ◽  
Atomic Layer ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Si Substrates ◽  
Layer Deposition ◽  
Structural And Electrical Properties

ABSTRACTWe investigated effects of thermal annealing on Ru films deposited on the 8 inch Si substrates using a volatile liquid-phase Ru precursor, tricarbonyl-1,3-cyclohexadienyl ruthenium (Ru(CO)3(C6H8)) by an atomic layer deposition (ALD) technique. Structural and electrical properties of the films were characterized by scanning probe microscopy, X-ray diffractometry, sheet resistance. Grazing incidence X-ray diffraction (GIXRD) patterns show typical Ru hexagonal polycrystalline peaks as annealing temperature was increased. At the highest annealing temperature condition, Ta = 700 °C electrical resistivity become 6 times less than in as-deposited films.

Atomic layer deposition of HfO2, Al2O3, and HfAlOx using O3 and metal(diethylamino) precursors

2007 ◽  
Vol 22 (12) ◽  
pp. 3455-3464 ◽  
Author(s):  
Rajesh Katamreddy ◽  
Ronald Inman ◽  
Gregory Jursich ◽  
Axel Soulet ◽  
Christos Takoudis
Keyword(s):  
Atomic Layer Deposition ◽  
Photoelectron Spectroscopy ◽  
Thermal Characteristics ◽  
Atomic Layer ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Metal Precursors ◽  
Layer Deposition ◽  
Xrd Techniques

Tetrakis-diethylamino hafnium (TDEAH), tris-diethylamino aluminum (TDEAA), and ozone were used for the atomic layer deposition (ALD) of HfO2, Al2O3, and HfAlOx films. The ALD rates were measured to be 1.1 Å/cycle for HfO2 and 1.3 Å/cycle for Al2O3. The ALD temperature windows were found to be between 200 and 325 °C for TDEAA, and between 200 and 275 °C for TDEAH. The overlap of these ALD windows between 200 and 275 °C is critical for ALD of the composite film, HfAlOx. In addition to the overlapping ALD temperature windows, the two metal precursors have similar thermal characteristics, as shown by TGA and differential scanning calorimetry. As-deposited films and films postannealed at 600 and 800 °C films were analyzed using Fourier transformed infrared (FTIR) spectroscopy, x-ray photoelectron spectroscopy, and x-ray diffraction (XRD) techniques. FTIR spectra revealed interfacial oxide growth during deposition of both HfO2 and Al2O3 whose thickness increased with annealing temperature. The FTIR data also indicated hydroxyl and nitrate groups in the films; these species were removed after annealing in Ar at a temperature of ⩾600 °C. Both FTIR and XRD results indicated the crystallization of pure HfO2 after annealing at temperatures as low as 600 °C. On the other hand, pure Al2O3 remained amorphous after annealing at temperatures up to 800 °C. XRD data of the composite HfAlOx film show that films deposited by alternating five cycles of HfO2 and one cycle of Al2O3 remained amorphous after annealing at 600 °C. Rutherford backscattering analysis of HfAlOx deposited with a varied number of alternating HfO2 and Al2O3 cycles demonstrated a strong correlation between the cyclic dosage of TDEAA and TDEAH and the film composition.

scholarly journals Red Y2O3:Eu-Based Electroluminescent Device Prepared by Atomic Layer Deposition for Transparent Display Applications

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1505
Author(s):  
José Rosa ◽  
Mikko J. Heikkilä ◽  
Mika Sirkiä ◽  
Saoussen Merdes
Keyword(s):  
Atomic Layer Deposition ◽  
Atomic Layer ◽  
Driving Frequency ◽  
X Ray Diffraction ◽  
Electroluminescent Devices ◽  
X Ray ◽  
Layer Deposition ◽  
Transparent Display ◽  
High Processing ◽  
Luminance Efficiency

Y2O3:Eu is a promising red-emitting phosphor owing to its high luminance efficiency, chemical stability, and non-toxicity. Although Y2O3:Eu thin films can be prepared by various deposition methods, most of them require high processing temperatures in order to obtain a crystalline structure. In this work, we report on the fabrication of red Y2O3:Eu thin film phosphors and multilayer structure Y2O3:Eu-based electroluminescent devices by atomic layer deposition at 300 °C. The structural and optical properties of the phosphor films were investigated using X-ray diffraction and photoluminescence measurements, respectively, whereas the performance of the fabricated device was evaluated using electroluminescence measurements. X-ray diffraction measurements show a polycrystalline structure of the films whereas photoluminescence shows emission above 570 nm. Red electroluminescent devices with a luminance up to 40 cd/m2 at a driving frequency of 1 kHz and an efficiency of 0.28 Lm/W were achieved.

scholarly journals Growth and characterization of Cd1-xZnxTe (0 \leq x \leq 1) nanolayers grown by isothermal closed space atomic layer deposition on GaSb and GaAs

2018 ◽  
Vol 64 (3) ◽  
pp. 206
Author(s):  
R. S. Castillo Ojeda ◽  
Joel Díaz-Reyes ◽  
M. Galván-Arellano ◽  
K. N. Rivera-Hernández ◽  
M. S. Villa-Ramírez ◽  
...  
Keyword(s):  
High Resolution ◽  
Atomic Layer Deposition ◽  
Atomic Layer ◽  
Growth Surface ◽  
X Ray Diffraction ◽  
X Ray ◽  
Layer Deposition ◽  
Wide Range ◽  
Cdte Growth

In this work are presented the results obtained from the deposition ofCd1-xZnxTe nanolayers using as precursor the vapours of the elementsZn, Te, and a mixture of Cd and Zn on GaAs and GaSb (001) substrates by Atomic Layer Deposition technique (ALD), which allows the deposition of layers of nanometric dimensions. At each exposure of the growth surface to the of cation or anion precursors vapours, this surface is saturated. Therefore, it is considered that the process is self-regulated. The ZnTe layers were grown in a wide range of temperatures; however, ZnTe nanolayers with a shiny mirror-like surface could be grown at temperatures between 370 and 410oC. Temperatures higher than 400oC were necessary for the CdTe growth. The layers of the Cd1-xZnxTe ternary alloy were deposited at temperature range of 400 and 425oC. The grown nanofilms were characterized by Raman spectroscopy and high-resolution X-ray diffraction. The Raman spectrumshows the peak corresponding to LO-ZnTe at 208 cm-1, which is weak and is slightly redshifted in comparison with the reported for the bulk ZnTe. For the case of the CdTe nanolayers, Raman spectrum presents the LO-CdTe peak, which is indicative of the successfully growth of the nanolayers, its weakness and its slight redshifted in comparison with the reported for the bulk CdTe can be related with the nanometric characteristic of this layer. The performed high resolution X-ray diffraction measurements allowed to study some importantcharacteristics, as the crystallinity of the grown layers. Additionally, the performed HR-XRD measurements suggest that the crystalline quality have dependence with the growth temperature.

Sign in / Sign up

Export Citation Format

Share Document