scholarly journals Размеры скачков и уровни деформации металлов

2018 ◽  
Vol 44 (15) ◽  
pp. 80
Author(s):  
В.В. Шпейзман
Keyword(s):  
Strain Rate ◽  
Interferometric Method ◽  
Burgers Vector ◽  
Deformation Jump ◽  
Copper Lead

AbstractIt is proposed to characterize levels of deformation by a size of its jumps, which can be observed when the strain rate is accurately measured in experiments with load that is constant or defined according a certain law. At the micro- and nanometer scales, the strain rate was measured and the deformation jumps were computed for copper, lead, and tin using a precision interferometric method. A correlation of the size of jumps with the Burgers vector of dislocations in metals was shown, and hypotheses about ensembles of dislocations participating in the formation of a deformation jump are made.

Dislocation Substructures Produced During Tensile, Creep, and Fatigue Deformation of Ti3Al at 700°C

1977 ◽  
Vol 35 ◽  
pp. 272-273
Author(s):  
S. M. L. Sastry
Keyword(s):  
Intermetallic Compound ◽  
Strain Rate ◽  
Tensile Creep ◽  
Slip Systems ◽  
Slip Vector ◽  
Superlattice Structure ◽  
Slip Activity ◽  
Dislocation Arrangement ◽  
Ordered Intermetallic ◽  
Tangled Dislocation

Ti3Al is an ordered intermetallic compound having the DO19-type superlattice structure. The compound exhibits very limited ductility in tension below 700°C because of a pronounced planarity of slip and the absence of a sufficient number of independent slip systems. Significant differences in slip behavior in the compound as a result of differences in strain rate and mode of deformation are reported here.Figure 1 is a comparison of dislocation substructures in polycrystalline Ti3Al specimens deformed in tension, creep, and fatigue. Slip activity on both the basal and prism planes is observed for each mode of deformation. The dominant slip vector in unidirectional deformation is the a-type (b) = <1120>) (Fig. la). The dislocations are straight, occur for the most part in a screw orientation, and are arranged in planar bands. In contrast, the dislocation distribution in specimens crept at 700°C (Fig. lb) is characterized by a much reduced planarity of slip, a tangled dislocation arrangement instead of planar bands, and an increased incidence of nonbasal slip vectors.

Quantitative analysis of in situ straining experiments in the case of strong frictional forces

1978 ◽  
Vol 36 (1) ◽  
pp. 570-571
Author(s):  
F. Louchet ◽  
L.P. Kubin
Keyword(s):  
Strain Rate ◽  
Radiation Effects ◽  
Dislocation Line ◽  
Critical Length ◽  
Local Strain ◽  
Local Flow ◽  
Double Kink ◽  
Dislocation Densities ◽  
Frictional Forces ◽  
Local Strain Rate

Investigation of frictional forces -Experimental techniques and working conditions in the high voltage electron microscope have already been described (1). Care has been taken in order to minimize both surface and radiation effects under deformation conditions.Dislocation densities and velocities are measured on the records of the deformation. It can be noticed that mobile dislocation densities can be far below the total dislocation density in the operative system. The local strain-rate can be deduced from these measurements. The local flow stresses are deduced from the curvature radii of the dislocations when the local strain-rate reaches the values of ∿ 10-4 s-1.For a straight screw segment of length L moving by double-kink nucleation between two pinning points, the velocity is :where ΔG(τ) is the activation energy and lc the critical length for double-kink nucleation. The term L/lc takes into account the number of simultaneous attempts for double-kink nucleation on the dislocation line.

Dislocations in alumina deformed by prismatic slip

1978 ◽  
Vol 36 (1) ◽  
pp. 606-607
Author(s):  
J. Cadoz ◽  
J. Castaing ◽  
J. Philibert
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Basal Slip ◽  
Prismatic Slip ◽  
Compression Tests ◽  
Thin Sections ◽  
Burgers Vector ◽  
Maximum Deformation ◽  
Transmission Electron ◽  
Mechanical Thinning

Plastic deformation of alumina has been much studied; basal slip occurs and dislocation structures have been investigated by transmission electron microscopy (T.E.M.) (1). Non basal slip has been observed (2); the prismatic glide system <1010> {1210} has been obtained by compression tests between 1400°C and 1800°C (3). Dislocations with <0110> burgers vector were identified using a 100 kV microscope(4).We describe the dislocation structures after prismatic slip, using high voltage T.E.M. which gives much information.Compression tests were performed at constant strainrate (∿10-4s-1); the maximum deformation reached was 0.03. Thin sections were cut from specimens deformed at 1450°C, either parallel to the glide plane or perpendicular to the glide direction. After mechanical thinning, foils were produced by ion bombardment. Details on experimental techniques can be obtained through reference (3).

Observations of dislocation interactions with recrystallized grain boundaries

1988 ◽  
Vol 46 ◽  
pp. 628-629
Author(s):  
C. W. Price
Keyword(s):  
Dislocation Density ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Dislocation Structure ◽  
Hot Deformation ◽  
Static Recrystallization ◽  
High Dislocation Density ◽  
High Angle ◽  
Dislocation Interactions

Little evidence exists on the interaction of individual dislocations with recrystallized grain boundaries, primarily because of the severely overlapping contrast of the high dislocation density usually present during recrystallization. Interesting evidence of such interaction, Fig. 1, was discovered during examination of some old work on the hot deformation of Al-4.64 Cu. The specimen was deformed in a programmable thermomechanical instrument at 527 C and a strain rate of 25 cm/cm/s to a strain of 0.7. Static recrystallization occurred during a post anneal of 23 s also at 527 C. The figure shows evidence of dissociation of a subboundary at an intersection with a recrystallized high-angle grain boundary. At least one set of dislocations appears to be out of contrast in Fig. 1, and a grainboundary precipitate also is visible. Unfortunately, only subgrain sizes were of interest at the time the micrograph was recorded, and no attempt was made to analyze the dislocation structure.

Defects in ion implanted silicon

1978 ◽  
Vol 36 (1) ◽  
pp. 386-387
Author(s):  
J.A. Lambert ◽  
P.S. Dobson
Keyword(s):  
Defect Structure ◽  
Dislocation Loops ◽  
Frank Loop ◽  
Burgers Vector ◽  
Temperature Range ◽  
Perfect Dislocation ◽  
Contrast Analysis ◽  
Image Position ◽  
Ion Implanted

The defect structure of ion-implanted silicon, which has been annealed in the temperature range 800°C-1100°C, consists of extrinsic Frank faulted loops and perfect dislocation loops, together with‘rod like’ defects elongated along <110> directions. Various structures have been suggested for the elongated defects and it was argued that an extrinsically faulted Frank loop could undergo partial shear to yield an intrinsically faulted defect having a Burgers vector of 1/6 <411>.This defect has been observed in boron implanted silicon (1015 B+ cm-2 40KeV) and a detailed contrast analysis has confirmed the proposed structure.

Determination of the Burgers vector of a dislocation in a Fe-Mn alloy by weak-beam image in HVEM

1978 ◽  
Vol 36 (1) ◽  
pp. 330-331
Author(s):  
Y. Ishida ◽  
H. Ishida ◽  
K. Kohra ◽  
H. Ichinose
Keyword(s):  
High Order ◽  
Simulation Technique ◽  
The Other ◽  
Image Simulation ◽  
Diffraction Vector ◽  
Burgers Vector ◽  
Weak Beam ◽  
Beam Image ◽  
Edge Component

IntroductionA simple and accurate technique to determine the Burgers vector of a dislocation has become feasible with the advent of HVEM. The conventional image vanishing technique(1) using Bragg conditions with the diffraction vector perpendicular to the Burgers vector suffers from various drawbacks; The dislocation image appears even when the g.b = 0 criterion is satisfied, if the edge component of the dislocation is large. On the other hand, the image disappears for certain high order diffractions even when g.b ≠ 0. Furthermore, the determination of the magnitude of the Burgers vector is not easy with the criterion. Recent image simulation technique is free from the ambiguities but require too many parameters for the computation. The weak-beam “fringe counting” technique investigated in the present study is immune from the problems. Even the magnitude of the Burgers vector is determined from the number of the terminating thickness fringes at the exit of the dislocation in wedge shaped foil surfaces.

Black-white contrast of dislocation loops

1978 ◽  
Vol 36 (1) ◽  
pp. 328-329
Author(s):  
J. J. Hren ◽  
W. D. Cooper ◽  
L. J. Sykes
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Dislocation Loops ◽  
Major Premise ◽  
Burgers Vector ◽  
Transmission Electron ◽  
Primary Means ◽  
Contrast Analysis ◽  
Dot Product ◽  
Imaging Conditions

Small dislocation loops observed by transmission electron microscopy exhibit a characteristic black-white strain contrast when observed under dynamical imaging conditions. In many cases, the topography and orientation of the image may be used to determine the nature of the loop crystallography. Two distinct but somewhat overlapping procedures have been developed for the contrast analysis and identification of small dislocation loops. One group of investigators has emphasized the use of the topography of the image as the principle tool for analysis. The major premise of this method is that the characteristic details of the image topography are dependent only on the magnitude of the dot product between the loop Burgers vector and the diffracting vector. This technique is commonly referred to as the (g•b) analysis. A second group of investigators has emphasized the use of the orientation of the direction of black-white contrast as the primary means of analysis.

Observation of dislocations in dynamically loaded Cu-SiO2

1986 ◽  
Vol 44 ◽  
pp. 424-425
Author(s):  
D. S. Pritchard
Keyword(s):  
Electron Microscope ◽  
Strain Rate ◽  
Single Crystal ◽  
Transmission Electron Microscope ◽  
Volume Fraction ◽  
Screw Dislocations ◽  
Spherical Inclusions ◽  
Transmission Electron ◽  
Crystal Dispersion ◽  
Strain Rate Loading

The effect of varying the strain rate loading conditions in compression on a copper single crystal dispersion-hardened with SiO2 particles has been examined. These particles appear as small spherical inclusions in the copper lattice and have a volume fraction of 0.6%. The structure of representative crystals was examined prior to any testing on a transmission electron microscope (TEM) to determine the nature of the dislocations initially present in the tested crystals. Only a few scattered edge and screw dislocations were viewed in those specimens.

The effects of strain and strain rate on residual microstructures in copper

1986 ◽  
Vol 44 ◽  
pp. 420-421
Author(s):  
M. F. Stevens ◽  
P. S. Follansbee
Keyword(s):  
Strain Rate ◽  
Applied Stress ◽  
Threshold Stress ◽  
Rate Sensitivity ◽  
Viscous Drag ◽  
Strain Rates ◽  
Strain And Strain Rate ◽  
Threshold Strength ◽  
Mechanism Transition ◽  
Intrinsic Strength

The strain rate sensitivity of a variety of materials is known to increase rapidly at strain rates exceeding ∼103 sec-1. This transition has most often in the past been attributed to a transition from thermally activated guide to viscous drag control. An important condition for imposition of dislocation drag effects is that the applied stress, σ, must be on the order of or greater than the threshold stress, which is the flow stress at OK. From Fig. 1, it can be seen for OFE Cu that the ratio of the applied stress to threshold stress remains constant even at strain rates as high as 104 sec-1 suggesting that there is not a mechanism transition but that the intrinsic strength is increasing, since the threshold strength is a mechanical measure of intrinsic strength. These measurements were made at constant strain levels of 0.2, wnich is not a guarantee of constant microstructure. The increase in threshold stress at higher strain rates is a strong indication that the microstructural evolution is a function of strain rate and that the dependence becomes stronger at high strain rates.

Direct structure images of 30° partial dislocation cores in silicon

1987 ◽  
Vol 45 ◽  
pp. 242-243
Author(s):  
J. C. Barry ◽  
H. Alexander
Keyword(s):  
Dislocation Core ◽  
Preparation Technique ◽  
Burgers Vector ◽  
Vector Type ◽  
Sample Preparation Technique ◽  
Lattice Images ◽  
Dislocation Core Structure ◽  
Type Lattice ◽  
Direct Inspection

Dislocations in silicon produced by plastic deformation are generally dissociated into partials. 60° dislocations (Burgers vector type 1/2[101]) are dissociated into 30°(Burgers vector type 1/6[211]) and 90°(Burgers vector type 1/6[112]) dislocations. The 30° partials may be either of “glide” or “shuffle” type. Lattice images of the 30° dislocation have been obtained with a JEM 100B, and with a JEM 200Cx. In the aforementioned experiments a reasonable but imperfect match was obtained with calculated images for the “glide” model. In the present experiment direct structure images of 30° dislocation cores have been obtained with a JEOL 4000EX. It is possible to deduce the 30° dislocation core structure by direct inspection of the images. Dislocations were produced by compression of single crystal Si (sample preparation technique described in Alexander et al.).

Sign in / Sign up

Export Citation Format

Share Document