scholarly journals Influence of Pre-Stressing on Tieback Retaining Wall for Sandy Soils Excavations

2021 ◽  
Vol 7 (3) ◽  
pp. 253
Author(s):  
Anthonius Steven Sutanto ◽  
Paulus Pramono Rahardjo ◽  
Aswin Lim
Keyword(s):  
Retaining Wall ◽  
Friction Angle ◽  
The Finite Element Method ◽  
Soil Pressure ◽  
Dense Sand ◽  
Wall Deflection ◽  
Length Increase ◽  
Braced Excavations ◽  
Embedment Length ◽  
Hardening Soil Model

Pre-stressed ground anchor systems or tieback systems are commonly used at wide and irregular-shaped excavations, with the advantage of lower cost and ease of construction compared to the braced excavations, but they come with the drawback on permits for excavations near buildings and tunnels. Research on tieback systems in sands was generally conducted. However, the studies on the correlation between the retaining wall deflection and pre-stress force are few. The objectives of this paper are to study the influence of pre-stress force, depth of excavation, wall embedment length, and soil shear strength that is represented by soil friction angle on the deflection and soil pressure acting on the retaining wall. The parametric study was conducted on an excavation in sand using the finite element method with the Hardening soil model. The results showed that a 50 kN/m increase in pre-stress force reduced the wall deflection on top of the wall by 0.005–0.083% of excavation depth. However, the pre-stressing influence in reducing wall deflection at excavations became less significant along with the sand density increase due to higher friction angle contribution to excavation stability. Moreover, the pre-stress force needed for stabilization of the wall with long embedment length is smaller than those on the wall with shorter embedment length, since the embedment length increase of 0.25 times of excavation depth reduces wall top deflection by 0.002–0.095% of excavation depth. Also, the increase of soil density reduces the need for wall embedment length, so at dense sand, the embedment length of 0.5 times of excavation depth is sufficient to support the excavation.

Unified Solution of Coulomb’s Active Earth Pressure for Unsaturated Soils without Crack

2012 ◽  
Vol 170-173 ◽  
pp. 755-761 ◽  
Author(s):  
Wen Biao Liang ◽  
Jun Hai Zhao ◽  
Yan Li ◽  
Chang Guang Zhang ◽  
Su Wang
Keyword(s):  
Principal Stress ◽  
Unsaturated Soils ◽  
Retaining Wall ◽  
Research Result ◽  
Earth Pressure ◽  
Friction Angle ◽  
Matric Suction ◽  
Intermediate Principal Stress ◽  
Active Earth Pressure ◽  
Soil Pressure

Based on the unified solution of shear strength in terms of double stress state variables for unsaturated soils, whilst considering the effect of the intermediate principal stress rationally, the unified solution of Coulomb’s active earth pressure for unsaturated soils without cracks is developed. Comparability of the solution is analyzed and influencing characteristic of each factor is obtained. The research result indicates that: the intermediate principal stress and matric suction have obvious impacts on Coulomb’s active earth pressure for unsaturated soils; Coulomb’s active earth pressure has been decreasing until zero with the increase of unified strength theory parameter and matric suction; Coulomb’s active earth pressure increases with the increase of grading angle of retaining wall and slop angle of backfill, but decreases with the increase of matric suction, effective internal friction angle and matric suction angle, while external friction angle has no obvious influence. The proposed unified solution of Coulomb’s active earth pressure enjoys a wider application, and unified solution of Rankine’s active earth pressure is just the special case. The results are of great significance to soil pressure determination such as slope and foundation pit, and to retaining structures design.

Deflection Analysis of Anchored Retaining Wall in Dune Sand

2013 ◽  
Vol 405-408 ◽  
pp. 101-105
Author(s):  
Yuri Daniel Jatoba Costa ◽  
John Gurgel ◽  
Carina Maia Lins Costa ◽  
Olavo Francisco Santos
Keyword(s):  
Retaining Wall ◽  
Soil Layer ◽  
Lateritic Soil ◽  
The Finite Element Method ◽  
Dune Sand ◽  
Bored Pile ◽  
Naturally Occurring ◽  
Deflection Analysis ◽  
Horizontal Wall ◽  
Embedment Length

This paper investigates the behavior of a 15-m high multi-anchored bored pile wall built in a dune sand overlying a naturally occurring lateritic soil layer. A parametric study using the finite element method was carried out to model wall deflections and ground movements during construction phases. Deflection results from the numerical simulations were compared to data collected in the field. The maximum horizontal wall deflection shows a non-linear decreasing trend with increasing system stiffness. Embedment length was found to play a secondary role on wall deflections. Predicted horizontal wall deflections after preloading of second and third anchor layers were on average 30% smaller than the corresponding field values.

NUMERICAL AND PHYSICAL MODELLING OF KAOLIN AS BACKFILL MATERIAL FOR POLYMER CONCRETE RETAINING WALL

2015 ◽  
Vol 76 (2) ◽  
Author(s):  
Ali Arefnia ◽  
Khairul Anuar Kassim ◽  
Houman Sohaei ◽  
Kamarudin Ahmad ◽  
Ahmad Safuan A Rashid
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Numerical Analysis ◽  
Retaining Wall ◽  
Laboratory Data ◽  
Physical Modelling ◽  
Horizontal Displacement ◽  
Polymer Concrete ◽  
The Finite Element Method ◽  
Backfill Material

 The failure mechanism of backfill material for retaining wall was studied by performing a numerical analysis using the finite element method. Kaolin is used as backfill material and retaining wall is constructed by Polymer Concrete. The laboratory data of an instrumented cantilever retaining wall are reexamined to confirm an experimental working hypothesis. The obtained laboratory data are the backfill settlement and horizontal displacement of the wall. The observed response demonstrates the backfill settlement and displacement of the retaining wall from the start to completion of loading. In conclusion, numerical modelling results based on computer programming by ABAQUS confirms the experimental results of the physical modelling.  

scholarly journals Evaluation of p-y Curves and p-multiplier of Pile Groups Corresponding to Sand Properties Change Based on 3D Numerical Analysis

2020 ◽  
Vol 20 (4) ◽  
pp. 207-217
Author(s):  
Yongjin Choi ◽  
Jaehun Ahn
Keyword(s):  
Numerical Analysis ◽  
Soil Properties ◽  
Pile Group ◽  
Friction Angle ◽  
Dominant Factor ◽  
Group Effect ◽  
Pile Groups ◽  
Dense Sand ◽  
Laterally Loaded Pile ◽  
Laterally Loaded

The <i>p-y</i> curve method and </i>p</i>-multiplier (<i>P<sub>m</sub></i>), which implies a group effect, are widely used to analyze the nonlinear behaviors of laterally loaded pile groups. Factors affecting <i>P<sub>m</sub></i> includes soil properties as well as group pile geometry and configuration. However, research on the change in <i>P<sub>m</sub></i> corresponding to soil properties has not been conducted well. In this study, in order to evaluate the effect of soil properties on the group effect in a laterally-loaded pile group installed in sandy soil, numerical analysis for a single pile and 3×3 pile group installed in loose, medium, and dense sand, was performed using the 3D numerical analysis program, Plaxis 3D. Among the factors considered in this study, the column location of the pile was the most dominant factor for <i>P<sub>m</sub></i>. The effect of the sand property change on <i>P<sub>m</sub></i> was not as significant as that of the column location of the pile. However, as the sand became denser and the friction angle increased, the group effect increased, leading to a decrease in <i>P<sub>m</sub></i> of approximately 0.1. This trend was similar to the result reported in a previous laboratory-scale experimental study.

scholarly journals Numerical Modelling of Soil Arching in a Shallow Backfill Layer

2015 ◽  
Vol 15 (4) ◽  
pp. 127-137 ◽  
Author(s):  
Waldemar St. Szajna
Keyword(s):  
Internal Friction ◽  
Flexible Structures ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Plasticity Condition ◽  
Flow Rule ◽  
The Finite Element Method ◽  
Soil Arching ◽  
Plain Strain ◽  
The Impact

Abstract The paper presents the application of the finite element method into the modelling of soil arching. The phenomenon plays fundamental role in soil-shell flexible structures behaviour. To evaluate the influence of arching on a pressure reduction, a plain strain trapdoor under a shallow layer of backfill was simulated. The Coulomb-Mohr plasticity condition and the nonassociated flow rule were used for the soil model. The research examines the impact of the internal friction angle and the influence of the backfill layer thickness on the value of soil arching. The carried out analyses indicate that the reduction of pressures acting on a structure depends on the value of the internal friction angle, which confirms the earlier research. For a shallow backfill layer however, the reduction is only a local phenomenon and can influence only a part of the structure.

Coefficients of active earth pressure with seepage effect

2012 ◽  
Vol 49 (6) ◽  
pp. 651-658 ◽  
Author(s):  
Pérsio L.A. Barros ◽  
Petrucio J. Santos
Keyword(s):  
Pore Water Pressure ◽  
Water Pressure ◽  
Retaining Wall ◽  
Drainage System ◽  
Numerical Procedure ◽  
Ground Surface ◽  
Earth Pressure ◽  
Friction Angle ◽  
Active Earth Pressure ◽  
Plane Failure

A calculation method for the active earth pressure on the possibly inclined face of a retaining wall provided with a drainage system along the soil–structure interface is presented. The soil is cohesionless and fully saturated to the ground surface. This situation may arise during heavy rainstorms. To solve the problem, the water seepage through the soil is first analyzed using a numerical procedure based on the boundary element method. Then, the obtained pore-water pressure is used in a Coulomb-type formulation, which supposes a plane failure surface inside the backfill when the wall movement is enough to put the soil mass in the active state. The formulation provides coefficients of active pressure with seepage effect which can be used to evaluate the active earth thrust on walls of any height. A series of charts with values of the coefficients of active earth pressure with seepage calculated for selected values of the soil internal friction angle, the wall–soil friction angle, and the wall face inclination is presented.

Pseudo-Dynamic Active Earth Pressure on Battered Face Retaining Wall Supporting c-Φ Backfill Considering Curvilinear Rupture Surface

2014 ◽  
Vol 5 (1) ◽  
pp. 39-57
Author(s):  
Sima Ghosh ◽  
Arijit Saha
Keyword(s):  
Wave Velocity ◽  
Retaining Wall ◽  
Pressure Coefficient ◽  
Wedge Angle ◽  
Earth Pressure ◽  
Friction Angle ◽  
Active Earth Pressure ◽  
Horizontal Shear ◽  
Rupture Surface ◽  
Wide Range

In the present analysis, using the horizontal slice method and D'Alembert's principle, a methodology is suggested to calculate the pseudo-dynamic active earth pressure on battered face retaining wall supporting cohesive-frictional backfill. Results are presented in tabular form. The analysis provides a curvilinear rupture surface depending on the wall-backfill parameters. Effects of a wide range of variation of parameters like wall inclination angle (a), wall friction angle (d), soil friction angle (F), shear wave velocity (Vs), primary wave velocity (Vp), horizontal and vertical seismic accelerations (kh, kv) along with horizontal shear and vertical loads and non-linear wedge angle on the seismic active earth pressure coefficient have been studied.

Sign in / Sign up

Export Citation Format

Share Document