scholarly journals Production and Characterization of Adsorbent from Oyster Shell (Crassostrea gigas) Using Physics and Chemical Activation with ZnCl2 and Its Application for Removal of Hexavalent Chromium

Elkawnie ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 329
Author(s):  
Lia Handayani ◽  
Azwar Thaib ◽  
Nurhayati Nurhayati ◽  
Yayuk Astuti ◽  
Adi Darmawan
Keyword(s):  
Hexavalent Chromium ◽  
Crassostrea Gigas ◽  
Chemical Activation ◽  
Oyster Shell ◽  
Sem Analysis ◽  
Raw Material ◽  
Physical Activation ◽  
Shell Waste

Abstract: Oyster shell waste has been investigated as a raw material for making adsorbents that will be activated. Physical activation uses temperatures of 500 ºC, 600 ºC, 700 ºC, 800 ºC, 900 ºC and chemical activation uses ZnCl2 with a concentration of 1 %, 5 %, 10 % and 15 %. Based on the analysis of the characteristics that have been carried out for physically activated adsorbents, the oyster shell calcined at 800 ºC produces the best characteristics, it is a radius of 35.11 Å with a percentage of removal of 38.04 %, as well as the results of the FTIR, XRF and SEM analysis gives the best results among others. Whereas for chemically activated adsorbents, the use of activator ZnCl2 10% produces adsorbents with the best characteristics among others with a radius of 84.14 Å and removal percentage of 65.68 %, the best results for adsorbents activated using 10% ZnCl2 are also supported by analysis results given by FTIR, XRF, and SEM.Keywords: Adsorbent; BET; Cr6+; Oyster Shell Waste; XRF Abstrak: Cangkang tiram (Crassostrea gigas) telah diteliti sebagai bahan baku pembuatan adsorben yang akan diaktivasi secara fisika dan kimia. Pembuatan adsorben dengan aktivasi secara fisika menggunakan variasi suhu 500 ºC, 600 ºC, 700 ºC, 800 ºC dan 900 ºC. sedangkan aktivasi kimia yaitu menggunakan aktivator ZnCl2 menggunakan variasi konsentrasi 1 %, 5 %, 10% dan 15 %. Berdasarkan analisa karakteristik yang telah dilakukan untuk adsorben-adsorben yang telah diaktivasi secara fisika, cangkang tiram yang di kalsinasi pada suhu 800ºC menghasilkan karakteristik yang paling baik, yaitu radius pori-pori 35,11 Å dengan persentase penyisihan sebesar 38,04 %, begitu pula dengan hasil analisa FTIR, XRF dan SEM memberikan hasil terbaik diantara yang lain. sedangkan untuk adsorben-adsorben yang diaktivasi secara kimia, penggunaan aktivator ZnCl2 10% menghasilkan adsorben dengan karakteristik yang paling baik diantara lainnya dengan radius pori-pori 84,14 Å dan persentase penyisihan sebesar 65,68%, hasil terbaik untuk adsorben yang diaktivasi menggunakan ZnCl2 10 % juga didukung oleh hasil analisa dari FTIR, XRF dan SEM.

scholarly journals Preparation of Composite Monolith Supercapacitor Electrode Made from Textile-Grade Polyacrylonitrile Fibers and Phenolic Resin

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 655
Author(s):  
Karim Nabil ◽  
Nabil Abdelmonem ◽  
Masanobu Nogami ◽  
Ibrahim Ismail
Keyword(s):  
Electrical Resistivity ◽  
Surface Area ◽  
Phenolic Resin ◽  
Physical Adsorption ◽  
Chemical Activation ◽  
Specific Capacity ◽  
Physical Activation ◽  
Gravimetric Analysis ◽  
Capacitive Properties

In this work a composite monolith was prepared from widely available and cost effective raw materials, textile-grade polyacrylonitrile (PAN) fibers and phenolic resin. Two activation procedures (physical and chemical) were used to increase the surface area of the produced carbon electrode. Characterization of the thermally stabilized fibers produced was made using differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA) and Carbon-Hydrogen-Nitrogen(CHN) elemental analysis, in order to choose the optimum conditions of producing the stabilized fibers. Characterization of the produced composite monolith electrode was performed using physical adsorption of nitrogen at 77 °K, cyclic voltammetry (CV), galvanostatic charge-discharge (GCD) and electrical resistivity in order to evaluate its performance. All the electrodes prepared had a mixture of micropores and mesopores. Pressing the green monolith during the curing process was found to reduce largely the specific surface area and to some degree the electrical resistivity of the chemically activated composite electrode. Physical activation was more suitable than chemical activation, where it resulted in an electrode with specific capacity 29 F/g, good capacitive behavior and the stability of the electrical resistivity over the temperature range −130 to 80 °C. Chemical activation resulted in a very poor electrode with resistive rather than capacitive properties.

AKTIVASI KIMIA-FISIK LIMBAH SERUTAN ROTAN MENJADI KARBON AKTIF

2014 ◽  
Vol 14 (1) ◽  
pp. 82-98
Author(s):  
Andy Mizwar
Keyword(s):  
Activated Carbon ◽  
Water Content ◽  
Iodine Number ◽  
Surface Area ◽  
Chemical Activation ◽  
Raw Material ◽  
Physical Activation ◽  
Fixed Carbon ◽  
Impregnation Time ◽  
Physical And Chemical

Limbah rotan dari industri kerajinan dan mebel berpotensi untuk dijadikan sebagai bahan baku pembuatan karbon aktif karena memiliki kandungan holoselulosa dan kadar karbon yang tinggi. Penelitian ini bertujuan untuk menganalisis efektifitas dari aktivasi kimia menggunakan larutan natrium klorida (NaCl) yang dilanjutkan dengan aktivasi fisik dalam pembuatan karbon aktif berbahan dasar  limbah serutan rotan. Pembuatan karbon aktif diawali dengan proses karbonisasi pada suhu 250°C selama 1 jam. Selanjutnya aktivasi kimia menggunakan larutan NaCl dengan variasi konsentrasi 10%, 15% dan 20% serta waktu perendaman selama 10, 15 dan 20 jam. Aktivasi fisik dilakukan dengan pembakaran pada suhu 700°C selama 30 menit. Analisis karakteristik fisik-kimia karbon aktif mengacu pada SNI 06-3730-95, meliputi kadar air, fixed carbon, dan iodine number, sedangkan perhitungan luas permukaan spesifik karbon aktif dilakukan dengan Metode Sears. Hasil penelitian ini menunjukkan bahwa kondisi optimum aktivasi kimia terjadi pada konsentrasi NaCl 10% dan lama perendaman 10 jam dengan hasil analisis kadar air 2.90%, fixed carbon 72.70%, iodine number 994.59 mg/g dan luas permukaan 1587.67 m²/g. Peningkatan fixed carbon, iodine number dan luas permukaan karbon aktif berbanding terbalik dengan peningkatan konsentrasi NaCl dan lama waktu perendaman, sedangkan peningkatan kadar air pada karbon aktif berlaku sebaliknya. Rattan waste from handicraft and furniture industry could potentially be used as raw material of activated carbon due to high content of holoselulosa and carbon. This paper investigates the effectiveness of chemical activation using sodium chloride (NaCl) followed by physical activation in the making of activated carbon-based on rattan shavings waste. Preparation of the activated carbon began with the carbonization process at 250°C for 1 hour. Furthermore chemical activation using a variation of NaCl concentrations 10%, 15% and 20% as well as the time of immersion 10, 15 and 20 hours. Physical activation was done by burning at 700°C for 30 minutes. Analysis of the physical and chemical characteristics of the activated carbon was referred to the SNI 06-3730-95, including of moisture content, fixed carbon and iodine number, while the calculation of the specific surface area was done by the Sears’s method. The results of this study showed that the optimum conditions of chemical activation occurred in impregnation by NaCl 10% for 10 hours. The water content, fixed carbon, iodine number and surface area of activated carbon was 2.90%, 72.70%, 994.59 mg/g and 1587.67 m²/g  respectively. The increase values of fixed carbon, iodine number, and surface area was inversely proportional to the increase of NaCl concentration and the length of impregnation time, while the increase of water content applied vice versa.

scholarly journals Karakteristik luas permukaan karbon aktif dari ampas tebu dengan aktivasi kimia

2018 ◽  
Vol 10 (3) ◽  
pp. 149
Author(s):  
Mahmud Sudibandriyo ◽  
L Lydia
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
Chemical Activation ◽  
High Surface ◽  
High Surface Area ◽  
Physical Activation ◽  
Mass Ratio ◽  
Characterization Of Activated Carbon

Surface area characterization of activated carbon from sugarcane baggase by chemical activationAdsorption is one the process with many applications in the industries such as in a separation or in gas storage. In this adsorption, adsorbent selection is the most important thing. One of the adsorbent most suitable for this process is activated carbon. Previous studies show that high surface area of activated carbon can be produced from sugarcane bagasse using activator ZnCl2. The research’s goal is to produce activated carbon from sugarcane bagasse and determine the effects of activator on the surface area of activated carbon produced. Activators used in this research are KOH and ZnCl2 with the mass ratio of activator/carbon are 1/1, 2/1 and 3/1. The results show that The highest surface area, 938,2 m2/g, is obtained by activation using KOH with mass ratio of activator/carbon 3/1, whereas the highest surface area by activation using ZnCl2 is 632 m2/g with mass ratio of activator/carbon 2/1. For comparison, preparation of activated carbon by physical activation is also done and the surface area is 293 m2/g.Keywords: Activated carbon, chemical activation, sugarcane bagasse, KOH, ZnCl2 Abstrak Adsorpsi merupakan salah satu proses yang banyak digunakan dalam industri baik dalam pemisahan maupun untuk penyimpanan gas. Pada proses adsorpsi ini, pemilihan adsorben merupakan hal yang sangat penting. Salah satu jenis adsorben yang sangat cocok untuk proses ini adalah karbon aktif. Penelusuran studi sebelumnya menunjukkan bahwa karbon aktif dengan luas permukaan yang cukup tinggi dapat dibuat dari ampas tebu dengan menggunakan aktivator ZnCl2. Penelitian ini bertujuan untuk menghasilkan karbon aktif dari ampas tebu dengan aktivasi kimia serta mengetahui pengaruh aktivator terhadap luas permukaan karbon aktif yang dihasilkan. Aktivator yang digunakan dalam penelitian ini adalah KOH dan ZnCl2 dengan rasio massa aktivator/massa karbon 1/1, 2/1, dan 3/1. Aktivasi dilakukan pada temperatur 700 oC selama 1 jam. Hasil penelitian menunjukkan bahwa luas permukaan tertinggi sebesar 938,2 m2/g diperoleh dengan aktivasi menggunakan KOH dengan rasio massa aktivator/massa arang 3/1, sedangkan aktivasi dengan menggunakan ZnCl2 diperoleh luas permukaan tertinggi sebesar 632 m2/g dengan rasio massa aktivator/massa arang 2/1. Sebagai pembanding, pada penelitian ini juga dilakukan pembuatan karbon aktif dengan metode aktivasi fisika dan diperoleh luas permukaan karbon aktif sebesar 293 m2/g.Kata kunci: Aktivasi kimia, ampas tebu, karbon aktif, KOH, ZnCl2

scholarly journals The Production and Characterization of Activated Carbon Electrodes from Pineapple Leaf Fibers for Supercapacitor Application

2020 ◽  
Vol 9 (1) ◽  
pp. 1-8
Author(s):  
Agustino Agustino ◽  
Rakhmawati Farma ◽  
Erman Taer
Keyword(s):  
Activated Carbon ◽  
Chemical Activation ◽  
Total Pore Volume ◽  
Amorphous Structure ◽  
Physical Activation ◽  
Carbon Electrode ◽  
Average Pore ◽  
Average Pore Radius ◽  
Supercapacitor Application

Elektroda karbon aktif berbasis serat daun nanas (SDN) telah berhasil diproduksi dengan proses tiga langkah berikut ini, yaitu: (i) aktivasi kimia, (ii) karbonisasi, dan (iii) aktivasi fisika. Aktivasi kimia dilakukan dengan menggunakan agen pengaktif KOH dengan konsetrasi 0,3 M. Karbonisasi dilakukan dalam lingkungan gas N2 pada temperatur 600oC dan diikuti oleh aktivasi fisika pada temperatur 850oC menggunakan gas CO2 selama 2,5 jam. Luas permukaan spesifik elektroda 512,211 m2×g-1 dengan volume total pori sebesar 0,093 cm3×g–1, dan jari-jari pori rata-rata 1,199 nm. Morfologi permukaan elektroda karbon aktif menunjukkan adanya serat karbon dengan diameter serat dalam kisaran 101 - 185 nm dan memliki kandungan karbon dengan massa atomik sebesar 84,33%. Elektroda karbon aktif memiliki struktur amorf, yang ditunjukkan oleh dua puncak difraksi yang lebar pada sudut hamburan 24,64 dan 43,77o yang bersesuaian dengan bidang (002) dan (100). Kapasitansi spesifik, energi spesifik dan daya spesifik sel superkapasitor yang dihasilkan masing-masing sebesar 110 F×g-1, 15,28 Wh×kg-1 dan 36,69 W×kg-1. Pineapple leaf fiber (PALF) based activated carbon electrode has been successfully produced using three-step process, i.e. (i) chemical activation, (ii) carbonization, and (iii) physical activation. The chemical activation was carried out using KOH activating agent with a concentration of 0.3 M. The carbonization process is conducted out in N2 gas environment at 600oC and followed by physical activation at a temperature of 850oC by using CO2 gas for 2.5 h. The specific surface area of the electrode is 512.211 m2×g-1 with a total pore volume of 0.093 cm3×g-1, and average pore radius of 1.199 nm. The surface morphology of the electrode shown the carbon fibers with diameter in the range of 101 - 185 nm and carbon content with 84.33% of atomic mass. The activated carbon electrode has an amorphous structure, which is shown by two wide diffraction peaks at scattering angles of 24.64 and 43.77o which correspond to the plane (002) and (100), respectively. The specific capacitance, energy and power of the electrode are 110 F×g-1, 15.28 Wh×kg-1 and 36.69 W×kg-1, respectively.Keywords: Serat daun nanas, Kalium hidroksida, Elektroda karbon aktif, Kapasitansi spesifik, Superkapasitor 

scholarly journals Activated Carbons (AC) Prepared by Direct CO2 Activation of Parsea Americana seeds Biomass for Supercapacitor Electrodes

2021 ◽  
Vol 2049 (1) ◽  
pp. 012067
Author(s):  
Rakhmawati Farma ◽  
Ramadani Putri Anakis ◽  
Irma Apriyani
Keyword(s):  
Activated Carbons ◽  
Chemical Activation ◽  
Physical Activation ◽  
Co2 Activation ◽  
X Ray Diffraction ◽  
Activation Temperature ◽  
X Ray ◽  
Cyclic Voltametry ◽  
Scanning Electron

Abstract Biomass converted into activated carbon (AC) by using physical activation method can form micro-meso pore structure and maintain the interconnected natural pore network of biomass. AC is prepared from the biomass of Parsea Americana seeds (PAS) through a process of pre-carbonization, chemical activation, carbonization and physical activation which is activated at temperatures of 700°C, 800°C, and 900°C. Characterization of physical properties of AC electrodes consisted of X-ray diffraction, Scanning Electron Microscope-Energy Dispersive X-ray and characterization of electrochemical properties of supercapacitor cells using Cyclic Voltametry. The results showed that the microstructure of the AC electrode has a semicrystalline structure characterized by the presence of two sloping peaks at an angle of 2θ around 24° and 44° which corresponded to the hkl (002) and (100) planes, where the lowest Lc value was produced by the PAS-900 sample. The PAS-900 sample had aggregates or lumps with smaller size in small amounts in the presence of micro-mesopores and had the highest carbon content of 94.50% with the highest capacitance value of 203.12 F/g. The temperature of 900°C is the best activation temperature in the process of manufacture AC electrodes from Parsea Americana seeds biomass for supercapacitor cell applications.

scholarly journals Synthesis and characterization of graphene layers from rice husks

2018 ◽  
pp. 12-18
Author(s):  
Makpal Seitzhanova ◽  
Dmitry Chenchik ◽  
Mukhtar Yeleuov ◽  
Zulkhair Mansurov ◽  
Roberto Di Capua ◽  
...  
Keyword(s):  
Raman Spectroscopy ◽  
Rice Husk ◽  
Renewable Resources ◽  
Large Scale ◽  
Low Cost ◽  
Chemical Activation ◽  
Raw Material ◽  
Graphene Layers ◽  
Naoh Solution

In this work, a method of obtaining graphene layers from natural source specifically from rice husk was developed. A rice husk (RH) was used as a raw material, and potassium hydroxide was used as activation agent. The graphene layers were obtained after four successive stages: pre-carbonization, desilication in 1M NaOH solution, chemical activation and exfoliation of the carbonized rice husk (CRH). The obtained samples were studied using Raman spectroscopy, TEM and SEM; the Raman peaks evidenced the presence of graphene multilayers in the sample. A detailed observation of Raman spectroscopy showed that the obtained samples with ratio of 1/4 and 1/5 (RH/KOH) consisted of graphene layers with a high content of amorphous component. The yield of the product was ~ 3% by weight. This study can provide a new way to the large-scale synthesis of low-cost single and multi-layered graphene using rice husk or other renewable resources.

scholarly journals Utilization and Characterization of Oyster Shell as Chitosan and Nanochitosan

2018 ◽  
Vol 21 (4) ◽  
pp. 224-231
Author(s):  
Lia Handayani ◽  
Faisal Syahputra ◽  
Yayuk Astuti
Keyword(s):  
Particle Size ◽  
Morphological Analysis ◽  
Oyster Shell ◽  
Tween 80 ◽  
Raw Material ◽  
Initial Weight ◽  
Deacetylation Degree ◽  
Chitosan Particle

Oyster is one of bivalve groups widely consumed by human, thus, it results in producing huge waste shells affecting the environment. One way to increase the value of oyster shells is to process them into chitosan. This study aims to isolate chitin then synthesize it into chitosan and convert chitosan into nano-sized chitosan and analyze the characteristics. The steps to produce chitosan from waste shells included demineralization using HCl 1 N and deproteinization using NaOH 3%. The next step was to convert chitin into chitosan through a deacetylation process using NaOH 50%. After chitosan was formed, it was continued to convert chitosan into nano chitosan particles using ion gelation method with the addition of surfactant (tween 80) and crosslinker (TPP 0.1% and 0.5%). The results showed that yield of transformation chitin into chitosan was 61.1%. Meanwhile, the yield calculated from initial weight of raw material was 18.33% with deacetylation degree value equal to 89.14%. Based on morphological analysis using SEM, the size of chitosan particles was not distributed homogeneously that was in the range of 892 nm-1.54 μm, while the nano chitosan particle size obtained was uniformly formed in the range of 679 nm-910 nm.

scholarly journals In situ distribution and characterization of the organic content of the oyster shell Crassostrea gigas (Mollusca, Bivalvia)

Micron ◽  
2013 ◽  
Vol 44 ◽  
pp. 373-383 ◽  
Author(s):  
Yannicke Dauphin ◽  
Alexander D. Ball ◽  
Hiram Castillo-Michel ◽  
Corinne Chevallard ◽  
Jean-Pierre Cuif ◽  
...  
Keyword(s):  
Crassostrea Gigas ◽  
Oyster Shell ◽  
Organic Content

scholarly journals Synthesis and characterization of activated carbon from sugar beet residue for the adsorption of hexavalent chromium in aqueous solutions

RSC Advances ◽  
2021 ◽  
Vol 11 (14) ◽  
pp. 8025-8032
Author(s):  
Jiaming Zhao ◽  
Lihua Yu ◽  
Feng Zhou ◽  
Huixia Ma ◽  
Kongyan Yang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Sugar Beet ◽  
Aqueous Solutions ◽  
Hexavalent Chromium ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Synthesis And Characterization ◽  
Step Method ◽  
Characterization Of Activated Carbon

A series of micro–mesoporous activated carbons (ACs) were prepared from sugar beet residue by a two-step method including KOH chemical activation and were used for Cr(vi) removal from aqueous solutions.

scholarly journals Characterization of Activated Charcoal Oil Palm (Elaeis Guineensiss Jacq) Shell Waste using SEM and FTIR: Effect of Activation Temperature

2019 ◽  
Vol 2 (2) ◽  
pp. 67
Author(s):  
Rasyid Syidiq ◽  
La Ode Yusran ◽  
Muhammad Anas ◽  
Suritno Fayanto
Keyword(s):  
Oil Palm ◽  
Activated Charcoal ◽  
Sem Analysis ◽  
Absorption Bands ◽  
Activation Temperature ◽  
Carbonation Process ◽  
Oil Palm Shell ◽  
Shell Waste ◽  
Two Stages

This study aims to determine the structure of morphology and functional groups from activated charcoal for palm oil waste with variations in activation temperature. The process of two stages: the carbonation and activation stage. Carbonation process using a pyrolysis reactor at a carbonation temperature of 200oC -400oC for 6 hours. Then, the sample activated at a temperature of 700 °C, 750oC, 800oC, and 850 °C. Samples were characterization using SEM and FTIR. SEM analysis results show the largest pore size at a temperature of 850 oC with a diameter of 48.3 nm, and the lowest temperature was 700 °C with a capacity of 35.3 nm. Activated charcoal from oil palm shell waste at mesopore size. Next, FTIR analysis results show wave numbers 2165,18 cm-1, 1554 cm-1, 1030,76 cm-1 dan 424,11 cm-1.  The removal of some absorption bands and  the formation of new absorption bands, caused by the activation temperature

Sign in / Sign up

Export Citation Format

Share Document