scholarly journals Investigations of combustion process in combined cooker-boiler fired on solid fuels

2006 ◽  
Vol 10 (4) ◽  
pp. 121-130
Author(s):  
Dragoslava Stojiljkovic ◽  
Vladimir Jovanovic ◽  
Milan Radovanovic ◽  
Nebojsa Manic ◽  
Ivo Radulovic
Keyword(s):  
Flue Gas ◽  
Combustion Process ◽  
Solid Fuels ◽  
Gas Temperature ◽  
Weight Changes ◽  
Complete Combustion ◽  
Air Supply ◽  
Class 1 ◽  
Secondary Air ◽  
Co Emission

The aim of the investigation was to make some reconstructions on the existing stove used for cooking and baking and to obtain the combined cooker-boiler which will fulfill the demands of European standard EN 12815. Implementation of modern scientific achievements in the field of combustion on stoves and furnaces fired on solid fuels was used. During the investigations four various constructions were made with different fresh air inlet and secondary air supply with the intention to obtain more complete combustion with increased efficiency and reduced CO emission. Three different fuels were used: firewood, coal, and wood briquette. A numerous parameters were measured: fuel weight changes during the combustion process, temperature of inlet and outlet water, flue gas composition (O2, CO, SO2, CO2, NOx), flue gas temperature, ash quantity etc. The result of the investigations is the stove with the efficiency of more than 75% - boiler Class 1 (according EN 12815) and CO emission of about 1% v/v. The results obtained during the measurements were used as parameters for modeling of combustion process. .

Retrofit of WtE Boiler: Case Study on Bonn Plant

2002 ◽  
Author(s):  
Mark Pe´rilleux ◽  
Dirk Eeraerts
Keyword(s):  
Flue Gas ◽  
Gas Flow ◽  
Natural Circulation ◽  
Combustion Process ◽  
Circulation System ◽  
Gas Temperature ◽  
Complete Combustion ◽  
Parallel Flows ◽  
Secondary Air Injection ◽  
Secondary Air

The implementation of the European-directive requiring a residence time of at least two seconds at a temperature above 850°C (1562°F), the change in waste characteristics, and the pursuit of higher thermal efficiencies has pushed many of the existing WtE plants in Europe to their operational limits. Most existing WtE plants were not designed to operate under these conditions and may require modifications to the combustion system. Within the SEGHERS better technology (SEGHERS) company, the SEGHERS-IBB-Prism was developed to deal with the cause of these problems, which are essentially related to insufficient mixing and burnout of the flue gases in the combustion area. In the Boiler Prism the flue gas flow is divided into two parallel flows prior to entering the first radiant pass of the boiler. This division is achieved by means of a prism shaped construction, which is water-cooled and integrated with the natural circulation system of the boiler. Additional secondary air injection nozzles are fitted in the prism. This technology results in a more uniform flue gas temperature and a complete combustion of the flue gas immediately above the prism. In the Bonn Plant, these improvements in the combustion process resulted in a decrease of the fireside cleaning requirements of more than 50%.

Waste Combustion Technology and Air Emission Control Developments by Fisia Babcock Environment

2011 ◽  
Author(s):  
Jens Sohnemann ◽  
Walter Scha¨fers ◽  
Armin Main
Keyword(s):  
Flue Gas ◽  
Combustion Process ◽  
Great Majority ◽  
Optimum Process ◽  
Cleaning Process ◽  
Gas Temperature ◽  
Flash Evaporation ◽  
Limit Values ◽  
Gas Cleaning ◽  
Secondary Air

The efforts for reducing the emissions into the atmosphere start already in the furnace and are completed by an effective flue gas cleaning system. This implies the necessity for design developments of key components for a modern EfW plant. For the core component of the firing system — the grate — Fisia Babcock Environment (FBE) is using forward moving grates as well as roller grates. The moving grate, which is used in the great majority of all our plants, has specific characteristics for providing uniform combustion and optimal burnout. These include, amongst others: - Uniform air supply by means of specific grate bar geometry. - Two grate steps in direction of waste transport for optimum burnout. - Flexible adaptation of the combustion process to the respective conditions and requirements by zone-specific air distribution and transport velocity of waste on grate. - Combustion control adapted to the specific plant for ensuring a consistent combustion process and production of energy. In addition to these features influencing the emissions the moving grate exhibits also specific characteristics regarding the mechanical aspects allowing low-maintenance and reliable operation. For optimum flue gas burnout a good oxygen distribution after leaving the combustion zone is required. For ensuring this, the injection of secondary air is designed to produce a double-swirl, developed by FBE. Final reduction of the nitrogen constituents NO and NO2 to the stipulated emission value is achieved by the SNCR process. As well in this respect, there is a great amount of experience available. Besides these measures regarding the combustion process, this paper also reports about flue gas cleaning systems. In this field the FBE CIRCUSORB® process is presented and compared with the known dry absorption process. CIRCUSORB® is a lime-based flue gas cleaning process with continuous recirculation of the moistened reaction product and simultaneous addition of fresh hydrated lime. The flue gas temperature downstream of the economizer can be selected very low and permits in this way maximized utilization of the energy. The evaporation of the moisture from the reaction product (flash evaporation) effects final cooling down of the flue gas to optimum process temperature and improves at the same time SO2 separation. This reduces the technical investment required for the flue gas cleaning process. The total of all measures taken and the robust design of all components permit economical plant operation while complying with the stipulated emission limit values.

Numerical Simulation of Combustion Process in a 350t/d MSW Incinerator

2012 ◽  
Vol 268-270 ◽  
pp. 898-901
Author(s):  
Shui E Yin ◽  
Jun Wu
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Combustion Process ◽  
Species Distributions ◽  
Complete Combustion ◽  
Operational Conditions ◽  
Furnace Outlet ◽  
Air Supply ◽  
Total Temperature ◽  
Secondary Air

A mathematical model was presented for the combustion of municipal solid waste in a 350t/d MSW-burning incinerator. Numerical simulations were performed to predict the temperature and the species distributions in the furnace, with practical operational conditions taken into account. When the total air supply is constant, reducing primary air and increasing secondary air properly results in the higher total temperature of the furnace and the more oxygen concentration at the furnace outlet, and thereby contributes to the complete combustion of combustibles so that an optimal combustion effect can be achieved.

scholarly journals Quality Function Deployment (QFD) and TRIZ in Briquette Cookstove Design and Simulation

2021 ◽  
Vol 12 (2) ◽  
pp. 349-359
Author(s):  
Niswatun Faria ◽  
◽  
Kuntum Khoiro Ummatin ◽  
Mochammad Annas Junianto ◽  
Tedy Eko Budiharso
Keyword(s):  
Flue Gas ◽  
Quality Function Deployment ◽  
Computational Simulation ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Concept Design ◽  
Complete Combustion ◽  
Air Inlet ◽  
Secondary Air ◽  
Chamber Capacity

Poor cookstove design can harm the user's health and environment. This research aims to obtain an efficient cookstove design, environmentally friendly and operated easily. The cookstove design process using a combination of QFD and TRIZ. QFD able to capture customer needs through a questionnaire and interview. The data collected then processed to build a House of Quality (HoQ), one of the tools in QFD. QFD results in the design parameter of the briquette cookstove, which is incorporated in the concept design. The TRIZ method is utilized to understand the problem that might occur in the concept design and focus on solving the root causes. The next step is a detailed design where the dimensions, combustion chamber capacity, and supporting features are explained. The combination of QFD and TRIZ result in a briquette cookstove concept design which is easy to clean and operate. The combustion system is Top-lit Up-Draft (TLUD). The burning chamber has two air inlets, namely primary and secondary. The primary air inlet supplies the air from the bottom of the burning chamber, partially burns the briquette, and produces flue gas. The secondary air inlet is in the shape of an oval to supply air in the burning chamber's upper part to burn the flue gas completely. A complete combustion process will increase combustion efficiency and reduce emissions. A computational simulation shows the velocity distribution inside the burning chamber.

scholarly journals Reduction of Major Pollutants via Air-staged Commbustion on Burner System

2013 ◽  
Vol 64 (1) ◽  
Author(s):  
Mohammad Nazri Mohd. Jaafar ◽  
Mohd Nur Hanafi Zaini
Keyword(s):  
Combustion Process ◽  
Primary Concern ◽  
Nox Emissions ◽  
Percent Reduction ◽  
Secondary Air ◽  
Secondary Zone ◽  
Combustion Processes ◽  
Different Gases ◽  
Air Staging ◽  
Co Emission

Emission from the combustion processes can cause adverse effect to the environment.  The formation of pollutants such as NOx, CO, CO2 and SOx are hazardous and harmful to the ecosystem.  The awareness about the pollution due to the combustion activities, particularly in industrial field has set off an effort to find more comprehensive and enhanced technologies to reduce these pollutants.  There are several methods that can be used to reduce the emissions of these pollutants either by combustion modifications or post combustion treatment.  In this research, the method used is the post combustion treatment, i.e. the air staging method.  By air staging techniques, some of the combustion air will be directed into the primary combustion zone, while the remaining air is directed into the secondary zone.  The function of the secondary air is to reduce the peak flame temperatures, which theoretically reduce the emissions of NOx emissions.  The primary concern for this research is to study the effectiveness of the air staging in reducing NOx, CO, SO2, and UHC emissions from the combustion process.  The results obtained showed significant reduction in all major pollutants, i.e., a 31.8 percent reduction for CO emission, 16.8 percent for NOx, 12.7 percent for SO2 and 10.3 percent for UHC.  These reductions were obtained at different equivalence ratios for different gases.

scholarly journals Lab-scale evaluation of possible mercury speciation in flue gas and mercury emission from combustion of pulverised solid fuels

2019 ◽  
Vol 201 ◽  
pp. 06001
Author(s):  
Maciej Cholewiński ◽  
Wiesław Rybak
Keyword(s):  
Flue Gas ◽  
Combustion Process ◽  
Flue Gases ◽  
Solid Fuels ◽  
Hard Coal ◽  
Scale Evaluation ◽  
Gaseous Products ◽  
Scale Method ◽  
Early Validation ◽  
Solid Biomass

In this work a new lab-scale method dedicated to the evaluation of both concentration and oxidation level of mercury in flue gases from pulverised fuel fired boiler was proposed. To detect the abovementioned parameters, 2 main steps need to be evaluated. Firstly, a calorimeter bomb is utilised - by a proper implementation of mass balance of mercury within substrates and products, the quantity of oxidised mercury in gaseous products can be evaluated. Then, to simulate solid fuel fired power unit and to calculate mercury concentrations in flue gases, one of the stoichiometric mathematical models of combustion process must be applied. Early validation of the method showed considerable differences between solid fuels in mercury oxidation efficiencies and concentrations in flue gasses. Four examined fuels (lignite, hard coal and 2 types of solid biomass) was investigated. Calculated mercury concentrations in raw flue gas (>700°C) varied between 4 and 75 µg/m3ref. The lowest quantity of oxidised forms ofHg in flue gases were identified in the case of investigated lignite (27% of total Hg), while significantly higher – for selected hard coal (72%) and one type of biomass (with high chlorine concentration; up to 98%).

scholarly journals Low Emissions Resulting from Combustion of Forest Biomass in a Small Scale Heating Device

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5495
Author(s):  
Karol Tucki ◽  
Olga Orynycz ◽  
Andrzej Wasiak ◽  
Antoni Świć ◽  
Leszek Mieszkalski ◽  
...  
Keyword(s):  
Combustion Process ◽  
The Other ◽  
Screw Conveyor ◽  
Small Scale ◽  
Heat Output ◽  
Maximum Heat ◽  
Heating Device ◽  
Air Supply ◽  
Low Emission ◽  
Secondary Air

The paper concerns the analysis of harmful emissions during the combustion process in households. The subject of the analysis is a low emission heating device with an output of 50 kW for burning biomass of forest origin (low-quality hardwoods or softwoods). The proposed boiler is automatically fed from the connected container by means of a screw conveyor. In this way, the optimum amount of fuel is supplied for maximum heat output (adjustment of the ratio of primary air to fuel). The proposed biomass heating system is equipped with a primary and secondary air supply system and exhaust gas sensors. This ensures optimal regulation of the air mixture and efficient and clean combustion. Proper control of the combustion process, control of the air supply by means of a lambda sensor and power control of the system ensure a low-emission combustion process. The system precisely adjusts to the heat demand. This results in highly efficient heating technology with low operating costs. In the presented work, the emission of exhaust gases from the proposed heating device during the combustion of woodchips and beech–oak pellets were measured. It is demonstrated that the proposed design of the boiler equipped with intelligent control significantly reduces emissions when the biomass solid fuels are used, e.g., CO emissions from beech and oak chips and pellets in the low-emission boiler—18 extract pipes shows the value <100 ppm, which is even lower than when gas is burned in the other boilers; on the other hand, the pine chips show even higher emission when burned in the low-emission burner. Consequently, the choice of biomass source and form of the fuel play some role in the emissions observed.

NOx Emission of Diesel Fuel Blended with Different Saturation Degrees of Biofuel and with Oxygenator

2014 ◽  
Vol 660 ◽  
pp. 397-401 ◽  
Author(s):  
Mohd Fareez Edzuan bin Abdullah ◽  
Mohd Hisyamuddin bin Sulaiman ◽  
Noor Aliah Binti Abdul Majid
Keyword(s):  
Diesel Fuel ◽  
Flue Gas ◽  
Combustion Process ◽  
Nox Emission ◽  
Dominant Factor ◽  
Compression Ignition ◽  
Nox Formation ◽  
Fuel Blends ◽  
Combustion Tests ◽  
Co Emission

This paper discusses the nitrogen oxides (NOx) emission characteristics of compression ignition diesel engine operating on diesel fuel blends with different saturation degrees of biofuel and with methanol. In order to investigate the dominant factor of increased NOx in biofuels, diesel combustion tests were conducted under idling condition and the tailpipe exhaust emissions were measured by a flue gas analyzer. The general trend where NOx emission increased and reduced carbon monoxide (CO) emission in the biofuel and methanol blend cases were observed. The NOx emission levels increased as the biofuel saturation degree decreased, where it may be suggested that the prompt NOx mechanism is significant in total NOx formation of biofuel combustion process.

The Partition Period of Thermodynamic Calculation and the Numerical Simulation for Lignite Blended Supercritical Boiler

2014 ◽  
Vol 1030-1032 ◽  
pp. 648-652
Author(s):  
Cai Ying Ban ◽  
Xu Ao Lu ◽  
Jian Meng Yang ◽  
Xu Ran ◽  
Feng Ying Liang
Keyword(s):  
Numerical Simulation ◽  
Flue Gas ◽  
Thermodynamic Calculation ◽  
Heat Load ◽  
Combustion Process ◽  
Heating Surface ◽  
Gas Temperature ◽  
Boiler Furnace ◽  
Geometry Model ◽  
The Impact

The purpose of this paper is to study the impact of furnace temperature and load after blending in lignite, based on CFD software FLUENT-6.3,this paper choose the appropriate geometry model and the physical and mathematical models, and numerical simulation of the different conditions 600MW supercritical once-through boiler blending lignite furnace combustion process is curried out. And through a 600MW supercritical coal-fired boiler furnace lignite blended performed sections thermodynamic calculation under different conditions, worked out the furnace flue gas temperature, CO, CO2concentration distribute trend and radiant heat each section surface heat load conditions. The specific amount were blended with 5%, 10%, 15%, 20% were not dried lignite and dried lignite 20% after five conditions. And obtained a conclusion is the temperature and radiation heating surface flue gas heat load in the overall trend under the various conditions.

scholarly journals Gas Combustion Efficiency Enhancement: Application Study of Intense Elestrostatic Field

2019 ◽  
Vol 56 (4) ◽  
pp. 3-16
Author(s):  
O. Krickis ◽  
N. Zeltins
Keyword(s):  
Electrostatic Field ◽  
Flue Gas ◽  
Combustion Process ◽  
Field Application ◽  
Process Efficiency ◽  
Simultaneous Increase ◽  
Efficiency Enhancement ◽  
Gas Temperature ◽  
Gas Combustion ◽  
The Impact

Abstract A number of international, European Union and Latvian legislative acts have been developed, which regulate the efficiency of gas combustion plants and greenhouse gas emissions in the atmosphere. These legislative acts require the development of new scientifically efficient methods for gas optimal combustion with a minor impact on the environment. In order to achieve such a goal, different methods can be used, but the most efficient is an intensive electrostatic field application to control combustion and harmful emission formation in premixed flames. In the framework of the current study, the authors developed a hybrid burner, which allowed generating an intensive electrostatic field with intensity of more than 1000 kV/m. The study also investigated the impact of such a field on the formation of harmful emissions, including CO2 and flue gas temperature. The empirical results showed that an intensive DC electrostatic field generated inside of the burner had an impact on the flame shape, CO2, NOx emissions and flue gas temperature. In its turn, by applying an intensive pulsating electrostatic field (multivariable experiment) it was possible to achieve the reduction in NOx, CO emissions with a simultaneous increase in flue gas temperature, which was related to combustion process efficiency enhancement.

Sign in / Sign up

Export Citation Format

Share Document