scholarly journals Effects of Retained Austenite on Hydrogen Embrittlement in TRIP-aided Bainitic Ferrite Steel Sheet

2021 ◽  
Vol 61 (4) ◽  
pp. 1315-1321
Author(s):  
Junya Kobayashi ◽  
Ryo Sakata ◽  
Naoya Kakefuda ◽  
Goroh Itoh ◽  
Tomohiko Hojo
Keyword(s):  
Hydrogen Embrittlement ◽  
Retained Austenite ◽  
Steel Sheet ◽  
Bainitic Ferrite ◽  
Ferrite Steel

scholarly journals Effect of Carbon Content and Intercritical Annealing on Microstructure and Mechanical Tensile Properties in FeCMnSiCr TRIP-Assisted Steels

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1546
Author(s):  
Enzo Tesser ◽  
Carlos Silva ◽  
Alfredo Artigas ◽  
Alberto Monsalve
Keyword(s):  
Carbon Content ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Intercritical Annealing ◽  
Bainitic Ferrite ◽  
Ferrite Matrix ◽  
Polygonal Ferrite ◽  
Isothermal Treatment ◽  
Ferrite Steel ◽  
Mechanical Tensile

Four TRIP (Transformation Induced Plasticity) assisted steels, three TBF (TRIP Bainitic Ferrite) steels and one TPF (TRIP Polygonal Ferrite) steel, were manufactured from three different carbon contents (0.2, 0.3 and 0.4 wt.% C), to study the evolution of their microstructure and tensile mechanical properties in 15 mm thick plates. TBF steels were subjected to the same austenitization heat treatment and subsequent bainitization isothermal treatment. The TPF steel was subjected to an intercritical annealing and subsequent isothermal bainitization treatment. All were microstructurally characterized by optical, scanning electron and atomic force microscopy, as well as X-ray diffraction. Mechanically, they were characterized by the ASTM E8 tensile test and fractographies. For the TBF steels, the results showed that when the carbon content increased, there were an increase in volume fraction of retained austenite, of the microconstituent “martensite/retained austenite” and in the tensile strength; and a decrease in the volume fraction of bainitic ferrite matrix and elongation; with an improvement in TRIP behavior due to the increase in retained austenite. The TPF steel presented around 50% ductile polygonal ferrite developing better TRIP behavior than the TBF steels. The evolution of the fractographies was ductile to brittle for TBF steels with an increase in carbon content, and for TPF, the appearance of the fracture surface was ductile.

scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

scholarly journals Tempering and Austempering of Double Soaked Medium Manganese Steels

2021 ◽  
Vol 7 ◽  
Author(s):  
Alexandra Glover ◽  
John G. Speer ◽  
Emmanuel De Moor
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
Bainitic Ferrite ◽  
Total Elongation ◽  
Uniaxial Tensile ◽  
Present Contribution ◽  
Uniaxial Tensile Testing ◽  
Manganese Steels

The addition of a tempering or austempering step to the double soaking of a 0.14C–7.17Mn (wt pct) steel was investigated in the present contribution. The double soaking heat treatment is a two-step intercritical annealing heat treatment, which generates microstructures of athermal martensite, retained austenite and ferrite when applied to medium manganese steels. Microstructures following double soaking and (aus)tempering contained a combination of retained austenite, athermal or tempered martensite, and blocky or bainitic ferrite. X-ray diffraction, dilatometry and transmission Kikuchi diffraction were utilized to investigate microstructural changes which occurred during tempering or austempering. The resulting mechanical properties were measured using uniaxial tensile testing. The double soaking plus tempering heat treatment was shown to generate an ultimate tensile strength of 1,340 MPa in combination with 28 pct total elongation while the double soaking plus austempering heat treatment resulted in an ultimate tensile strength of 1,675 MPa and total elongation of 22 pct. Overall, both novel heat treatments produced a combination of strength and ductility desired for the third generation of advanced high strength steels.

scholarly journals Effects of Residual Stress on Hydrogen Embrittlement of a Stretch-Formed Tempered Martensitic Steel Sheet

2020 ◽  
Author(s):  
Hayato Nishimura ◽  
Tomohiko Hojo ◽  
Saya Ajito ◽  
Yuki Shibayama ◽  
Motomichi Koyama ◽  
...  
Keyword(s):  
Residual Stress ◽  
Hydrogen Embrittlement ◽  
Steel Sheet ◽  
Martensitic Steel

Isothermal Transformation, Microstructure and Mechanical Properties of Ausformed Low-Carbon Carbide-Free Bainitic Steel

2018 ◽  
Vol 941 ◽  
pp. 329-333 ◽  
Author(s):  
Jiang Ying Meng ◽  
Lei Jie Zhao ◽  
Fan Huang ◽  
Fu Cheng Zhang ◽  
Li He Qian
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Isothermal Transformation ◽  
Bainitic Transformation ◽  
Isothermal Treatment ◽  
Bainitic Steel ◽  
Low Carbon ◽  
Microstructure And Mechanical Properties

In the present study, the effects of ausforming on the bainitic transformation, microstructure and mechanical properties of a low-carbon rich-silicon carbide-free bainitic steel have been investigated. Results show that prior ausforming shortens both the incubation period and finishing time of bainitic transformation during isothermal treatment at a temperature slightly above the Mspoint. The thicknesses of bainitic ferrite laths are reduced appreciably by ausforming; however, ausforming increases the amount of large blocks of retained austenite/martenisite and decreases the volume fraction of retained austenite. And accordingly, ausforming gives rise to significant increases in both yield and tensile strengths, but causes noticeable decreases in ductility and impact toughness.

scholarly journals Novel Approach of Nanostructured Bainitic Steels’ Production with Improved Toughness and Strength

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1220
Author(s):  
Peter Kirbiš ◽  
Ivan Anžel ◽  
Rebeka Rudolf ◽  
Mihael Brunčko
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fine Structure ◽  
Retained Austenite ◽  
Bainitic Ferrite ◽  
High Hardness ◽  
Tensile Tests ◽  
Isothermal Transformation ◽  
Impact Testing ◽  
Bainitic Steels

The tendencies of development within the field of engineering materials show a persistent trend towards the increase of strength and toughness. This pressure is particularly pronounced in the field of steels, since they compete with light alloys and composite materials in many applications. The improvement of steels’ mechanical properties is sought to be achieved with the formation of exceptionally fine microstructures ranging well into the nanoscale, which enable a substantial increase in strength without being detrimental to toughness. The preferred route by which such a structure can be produced is not by applying the external plastic deformation, but by controlling the phase transformation from austenite into ferrite at low temperatures. The formation of bainite in steels at temperatures lower than about 200 °C enables the obtainment of the bulk nanostructured materials purely by heat treatment. This offers the advantages of high productivity, as well as few constraints in regard to the shape and size of the workpiece when compared with other methods for the production of nanostructured metals. The development of novel bainitic steels was based on high Si or high Al alloys. These groups of steels distinguish a very fine microstructure, comprised predominantly of bainitic ferrite plates, and a small fraction of retained austenite, as well as carbides. The very fine structure, within which the thickness of individual bainitic ferrite plates can be as thin as 5 nm, is obtained purely by quenching and natural ageing, without the use of isothermal transformation, which is characteristic for most bainitic steels. By virtue of their fine structure and low retained austenite content, this group of steels can develop a very high hardness of up to 65 HRC, while retaining a considerable level of impact toughness. The mechanical properties were evaluated by hardness measurements, impact testing of notched and unnotched specimens, as well as compression and tensile tests. Additionally, the steels’ microstructures were characterised using light microscopy, field emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM). The obtained results confirmed that the strong refinement of the microstructural elements in the steels results in a combination of extremely high strength and very good toughness.

scholarly journals Microstructure and Mechanical Properties of Tempered Ausrolled Nanobainite Steel

Crystals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 573
Author(s):  
Jing Zhao ◽  
Dezheng Liu ◽  
Yan Li ◽  
Yongsheng Yang ◽  
Tiansheng Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Energy Yield ◽  
Partial Recovery ◽  
Fracture Appearance ◽  
The Impact

The microstructures and mechanical properties of ausrolled nanobainite steel, after being tempered at temperatures in the range of 200−400 °C, were investigated in this study. After being tempered, bainitic ferrite is coarsened and the volume fraction of retained austenite is reduced. The hardness and ultimate tensile strength decrease sharply. The impact energy, yield strength, and elongation increase with elevated tempered temperature at 200–300 °C but decrease with elevated tempered temperature when the samples are tempered at 350 °C and 400 °C. The fracture appearance of all the samples after impact tests is a brittle fracture. The variation of the mechanical properties may be due to partial recovery and recrystallization.

Sign in / Sign up

Export Citation Format

Share Document