scholarly journals Techniques used in Evaluating Performance of Solar Air Heater (SAH) Comprised of Winglet Type Roughness- A Review

Author(s):  
Ravi Ranjan ◽  
Prof. Shravan Vishwakarma ◽  
Prof. Pankaj Badgaiyan

There are multiple resource of energies but if we talk about renewable energy then solar energy is one of the renewable energy which is in demand because it is feasible and cheap.  Flat - plate solar air heaters (SAHs) are simplistic and stylish, and their heating pathway of implementation requires care and support. increasing Room temperature, elimination of moist from farm commodities, increasing temperature of industrialized goods, hardening of wood or timber, and other uses for SAHs are frequent. well there are several issues in SAH, but the biggest issues with the SAH is its ineffectiveness, which is caused by atmosphere's lower heat transferring ability. We present introduces on the work performed by a lot of scientists to boost the effectiveness of solar air heaters (SAHs) with various kinds of roughness area in this research article.

2018 ◽  
Vol 8 (01) ◽  
Author(s):  
Ambreesh Prasad Shukla ◽  
Rakesh Kushwaha ◽  
Bhupendra Gupta ◽  
Anand Bisen

Solar energy has emerged as one of the alternate to conventional sources of energy. Solar air heaters are one of the important devices to utilize solar energy. But, poor heat transfer coefficient is one of the major problem in solar air heater. In this research article, an attempt is made to increase heat transfer coefficient of solar air heater by putting Hollow bodies over the absorber plate. These resulted in increase in heat transfer coefficient, efficiency and increase in outlet temperature of air simultaneously


Jurnal MIPA ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 181
Author(s):  
Imriani Moroki ◽  
Alfrets Septy Wauran

Energi terbarukan adalah salah satu masalah energi paling terkenal saat ini. Ada beberapa sumber potensial energi terbarukan. Salah satu energi terbarukan yang umum dan sederhana adalah energi matahari. Masalah besar ketersediaan energi saat ini adalah terbatasnya sumber energi konvensional seperti bahan bakar. Ini semua sumber energi memiliki banyak masalah karena memiliki jumlah energi yang terbatas. Penting untuk membuat model dan analisis berdasarkan ketersediaan sumber energi. Energi matahari adalah energi terbarukan yang paling disukai di negara-negara khatulistiwa saat ini. Tergantung pada produksi energi surya di daerah tertentu untuk memiliki desain dan analisis energi matahari yang baik. Untuk memiliki analisis yang baik tentang itu, dalam makalah ini kami membuat model prediksi energi surya berdasarkan data iradiasi matahari. Kami membuat model energi surya dan angin dengan menggunakan Metode Autoregresif Integrated Moving Average (ARIMA). Model ini diimplementasikan oleh R Studio yang kuat dari statistik. Sebagai hasil akhir, kami mendapatkan model statistik solar yang dibandingkan dengan data aktualRenewable energy is one of the most fomous issues of energy today. There are some renewable energy potential sources. One of the common n simple renewable energy is solar energy. The big problem of the availability of energy today is the limeted sources of conventional enery like fuel. This all energy sources have a lot of problem because it has a limited number of energy. It is important to make a model and analysis based on the availability of the energy sources. Solar energy is the most prefered renewable energy in equator countries today. It depends on the production of solar energy in certain area to have a good design and analysis of  the solar energy. To have a good analysis of it, in this paper we make a prediction model of solar energy based on the data of solar irradiation. We make the solar and wind enery model by using Autoregresif Integrated Moving Average (ARIMA) Method. This model is implemented by R Studio that is a powerfull of statistical. As the final result, we got the statistical model of solar comparing with the actual data


2021 ◽  
Vol 13 (13) ◽  
pp. 7401
Author(s):  
Sedef E. Kara ◽  
Mustapha D. Ibrahim ◽  
Sahand Daneshvar

This paper examines the dual efficiency of bioenergy, renewable hydro energy, solar energy, wind energy, and geothermal energy for selected OECD countries through an integrated model with energy, economic, environmental, and social dimensions. Two questions are explored: Which renewable energy alternative is more dual efficient and productive? Which renewable energy alternative is best for a particular country? Data envelopment analysis (DEA) is used for the efficiency evaluation, and the global Malmquist productivity index is applied for productivity analysis. Results indicate bioenergy as the most efficient renewable energy alternative with a 20% increase in average efficiency in 2016 compared to 2012. Renewable hydro energy, wind energy, and solar energy show a 17.5%, 16%, and 11% increase, respectively. The average efficiency growth across all renewable energy alternatives signifies major advancement. Country performance in renewable energy is non-monolithic; therefore, they should customize their renewable energy portfolio accordingly to their strengths to enhance renewable energy efficiency. Renewable hydro appears to have the most positive productivity change in 2016 compared to 2012, while solar energy regressed in productivity due to its scale inefficiency. All renewable energy alternatives have relatively equal average pure efficiency change. The positive trend in efficiency and productivity provides an incentive for policy makers to pursue further development of renewable energy technologies with a focus on improving scale efficiency.


Author(s):  
Wirya Sarwana ◽  
Akihiko Anzai ◽  
Daichi Takami ◽  
Akira Yamamoto ◽  
Hisao Yoshida

Photocatalytic steam reforming of methane (PSRM) has been studied as an attractive method to produce hydrogen by utilizing photoenergy like solar energy around room temperature with metal-loaded photocatalysts, where methane...


Author(s):  
Stephanie Drozek ◽  
Christopher Damm ◽  
Ryan Enot ◽  
Andrew Hjortland ◽  
Brandon Jackson ◽  
...  

The purpose of this paper is to describe the implementation of a laboratory-scale solar thermal system for the Renewable Energy Systems Laboratory at the Milwaukee School of Engineering (MSOE). The system development began as a student senior design project where students designed and fabricated a laboratory-scale solar thermal system to complement an existing commercial solar energy system on campus. The solar thermal system is designed specifically for educating engineers. This laboratory equipment, including a solar light simulator, allows for variation of operating parameters to investigate their impact on system performance. The equipment will be utilized in two courses: Applied Thermodynamics, and Renewable Energy Utilization. During the solar thermal laboratories performed in these courses, students conduct experiments based on the American Society of Heating, Refrigeration and Air-Conditioning Engineers (ASHRAE) 93-2010 standard for testing and performance characterization of solar thermal systems. Their measurements are then used to quantify energy output, efficiency and losses of the system and subsystem components.


1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


Holzforschung ◽  
2011 ◽  
Vol 65 (4) ◽  
Author(s):  
Jenny Sabrina Gütsch ◽  
Herbert Sixta

Abstract The implementation of biorefinery concepts into existing pulp and paper mills is a key step for a sustainable utilization of the natural resource wood. Water prehydrolysis of wood is an interesting process for the recovery of xylo-oligosaccharides and derivatives thereof, while at the same time cellulose is preserved to a large extent for subsequent dissolving pulp production. The recovery of value-added products out of autohydrolyzates is frequently hindered by extensive lignin precipitation, especially at high temperatures. In this study, a new high-temperature adsorption process (HiTAC process) was developed, where lignin is removed directly after the autohydrolysis, which enables further processing of the autohydrolyzates. The suitability of activated charcoals as a selective adsorbent for lignin under process-relevant conditions (150 and 170°C) has not been considered up to now, because former experiments showed decreasing efficiency of charcoal adsorption of lignin with increasing temperature in the range 20–80°C. In contrast to these results, we demonstrated that the adsorption of lignin at 170°C directly after autohydrolysis is even more efficient than after cooling the hydrolyzate to room temperature. The formation of lignin precipitation and incrustations can thus be efficiently prevented by the HiTAC process. The carbohydrates in the autohydrolysis liquor remain unaffected over a wide charcoal concentration range and can be further processed to yield valuable products.


Sign in / Sign up

Export Citation Format

Share Document