scholarly journals Locally Produced UHPC: The Influence of Type and Content of Steel Fibres

2021 ◽  
Vol 64 (1) ◽  
pp. 31-52
Author(s):  
Ingrid Lande ◽  
Rein Terje Thorstensen
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Deformation Behaviour ◽  
Image Correlation ◽  
Material Strength ◽  
Content Type ◽  
Steel Fibres ◽  
Flexural Tensile Strength ◽  
Southern Norway

Abstract Ultra-high performance concrete might be a competitive alternative to normal concrete for some purposes. But despite research efforts during decades, utilisation is still not widespread. Reasons include limited competence and material availability. This paper presents one step of a research initiative aimed at facilitating the use of UHPC in Norway. The step presented here comprises the accumulated results from investigations on the influence steel fibres (content, type, and hybrid combination) have on material strength and deformation behaviour of locally produced UHPC, made with constituents found in southern Norway. 231 specimens were tested, spanning nine UHPC mixes. Digital Image Correlation (DIC) was successfully used to study crack propagation. Compressive strength of 166 MPa and E-modulus of 46 GPa were obtained, not being influenced by fibre content. The flexural tensile strength was found to be strongly dependent on variations in steel fibre properties and mix design. The highest flexural tensile strength was obtained for prisms with micro straight steel fibres alone, or in 50% combination with macro hooked-end fibres. The experimental results are considered in a theory-informed discussion. Suggestions are made on the use of steel fibres in locally produced UHPC, potentially lowering the cost by 30%.

scholarly journals Influence of Rapid Heat Treatment on the Shrinkage and Strength of High-Performance Concrete

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4102
Author(s):  
Jan Stindt ◽  
Patrick Forman ◽  
Peter Mark
Keyword(s):  
Heat Treatment ◽  
High Performance ◽  
High Performance Concrete ◽  
Treatment Time ◽  
Precast Concrete ◽  
Concrete Strength ◽  
Shrinkage Strain ◽  
Temperature Treatment ◽  
Production Flow ◽  
Steel Fibres

Resource-efficient precast concrete elements can be produced using high-performance concrete (HPC). A heat treatment accelerates hardening and thus enables early stripping. To minimise damages to the concrete structure, treatment time and temperature are regulated. This leads to temperature treatment times of more than 24 h, what seems too long for quick serial production (flow production) of HPC. To overcome this shortcoming and to accelerate production speed, the heat treatment is started here immediately after concreting. This in turn influences the shrinkage behaviour and the concrete strength. Therefore, shrinkage is investigated on prisms made from HPC with and without steel fibres, as well as on short beams with reinforcement ratios of 1.8% and 3.1%. Furthermore, the flexural and compressive strengths of the prisms are measured directly after heating and later on after 28 d. The specimens are heat-treated between 1 and 24 h at 80 °C and a relative humidity of 60%. Specimens without heating serve for reference. The results show that the shrinkage strain is pronouncedly reduced with increasing temperature duration and rebar ratio. Moreover, the compressive and flexural strength decrease with decreasing temperature duration, whereby the loss of strength can be compensated by adding steel fibres.

scholarly journals Characteristics of Recycled Polypropylene Fibers as an Addition to Concrete Fabrication Based on Portland Cement

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1827 ◽  
Author(s):  
Marcin Małek ◽  
Mateusz Jackowski ◽  
Waldemar Łasica ◽  
Marta Kadela
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Polypropylene Fibers ◽  
Split Tensile Strength ◽  
Recycled Polypropylene ◽  
Recycled Fibers

High-performance concrete has low tensile strength and brittle failure. In order to improve these properties of unreinforced concrete, the effects of adding recycled polypropylene fibers on the mechanical properties of concrete were investigated. The polypropylene fibers used were made from recycled plastic packaging for environmental reasons (long degradation time). The compressive, flexural and split tensile strengths after 1, 7, 14 and 28 days were tested. Moreover, the initial and final binding times were determined. This experimental work has included three different contents (0.5, 1.0 and 1.5 wt.% of cement) for two types of recycled polypropylene fibers. The addition of fibers improves the properties of concrete. The highest values of mechanical properties were obtained for concrete with 1.0% of polypropylene fibers for each type of fiber. The obtained effect of an increase in mechanical properties with the addition of recycled fibers compared to unreinforced concrete is unexpected and unparalleled for polypropylene fiber-reinforced concrete (69.7% and 39.4% increase in compressive strength for green polypropylene fiber (PPG) and white polypropylene fiber (PPW) respectively, 276.0% and 162.4% increase in flexural strength for PPG and PPW respectively, and 269.4% and 254.2% increase in split tensile strength for PPG and PPW respectively).

Prediction of splitting tensile strength of high-performance concrete

2002 ◽  
Vol 32 (8) ◽  
pp. 1251-1258 ◽  
Author(s):  
M.F.M Zain ◽  
H.B Mahmud ◽  
Ade Ilham ◽  
M Faizal
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Splitting Tensile Strength

The ability of high performance concrete to resist high temperature

2017 ◽  
Vol 8 (4) ◽  
pp. 392-401 ◽  
Author(s):  
Hassan A.M. Mhamoud ◽  
Jia Yanmin
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Mass Loss ◽  
High Performance ◽  
Elevated Temperatures ◽  
High Performance Concrete ◽  
Sharp Decrease ◽  
Test Results ◽  
Content Type ◽  
Chinese Standard

Purpose This study aims to focus on the resistance to elevated temperatures of up to 700ºC of high-performance concrete (HPC) compared to ordinary Portland concrete (OPC) with regards to mass loss and residual compressive and flexural strength. Design/methodology/approach Two mixtures were developed to test. The first mixture, OPC, was used as the control, and the second mixture was HPC. After 28 days under water (per Chinese standard), the samples were tested for compressive strength and residual strength. Findings The test results showed that at elevated temperatures of up to 500ºC, each mixture experienced mass loss. Below this temperature, the strength and the mass loss did not differ greatly. Originality/value When adding a 10 per cent silica fume, 25 per cent fly, 25 per cent slag to HPC, the compressive strength increased by 17 per cent and enhanced the residual compressive strength. A sharp decrease was observed in the residual flexural strength of HPC when compared to OPC after exposure to temperatures of 700ºC.

Sign in / Sign up

Export Citation Format

Share Document