Is It Possible to Obtain More Energy from Solar DH Field? Interpretation of Solar DH System Data

2021 ◽  
Vol 25 (1) ◽  
pp. 1284-1292
Author(s):  
Roberts Kaķis ◽  
Ilze Poļikarpova ◽  
Ieva Pakere ◽  
Dagnija Blumberga
Keyword(s):  
Air Temperature ◽  
Solar Collector ◽  
Large Scale ◽  
District Heating ◽  
Ambient Air ◽  
Energy Sector ◽  
Climatic Conditions ◽  
Water Tank ◽  
System Productivity ◽  
Ambient Air Temperature

Abstract Europe has a course to zero emissions by 2050, with a strong emphasis on energy sector. Due to climatic conditions in Latvia, district heating (DH) plays an important role in the energy sector. One of the solutions to achieve the set goals in DH is to introduce emission-free technology. Therefore, the popularity of installation of large-scale solar collector plants continues to increase in DH in Europe. The first large-scale solar collector field in the Baltic States was installed in 2019. Solar collector active area is 21 672 m2 with heat storage water tank 8000 m3. The article shows the first operation results of this system and evaluates influencing factors. The results of the analysis show that system productivity is mainly demanded by solar radiation, and the strongest correlation between these parameters were established in May. The highest correlation between ambient air temperature and produced thermal energy is reached when ambient air temperature is between 7 °C to 15 °C and production process has not been externally regulated. The temperature difference between flow and return temperatures of the heat carrier affect solar collector performance minimally and strong correlation was not observed.

scholarly journals An Experimental Study on Double-Glazed Flat Plate Solar Water Heating System in Turkey

2014 ◽  
Vol 564 ◽  
pp. 204-209 ◽  
Author(s):  
Ahmet Ozsoy ◽  
Sabahattin Demirer ◽  
Nor Maria Adam
Keyword(s):  
Experimental Study ◽  
Flat Plate ◽  
Air Temperature ◽  
Temperature Difference ◽  
Solar Collector ◽  
Heating System ◽  
Ambient Air ◽  
Hot Water ◽  
Solar Simulator ◽  
Ambient Air Temperature

Domestic hot water preparation systems with flat plate solar collectors are widely used in Turkey. In this collector, the temperature difference between the required water temperature and the ambient air temperature increase causes a decrease in the efficiency of the collector. In this study, the use of double glass in order to increase the efficiency of the collector is studied experimentally.The location is in Isparta South West Turkey. Experimental study is conducted in May 2013 at the Suleyman Demirel University, Isparta. The system components are solar simulator, solar collector, tank, circulation pump, flowmeter, thermocouples, data acquisition device and solar sensor. Solar collector system’s operating temperature is 50oC for winter also summer. The difference between the collector temperature and the ambient air temperature exceeds 25oC in many cases, were found to be more efficient double-glazed collectors. When the temperature difference is 40oC, using double glazing collector is 24% more efficient than using single glazing collector.

Performance Measurements of a Cylindrical Glass Honeycomb Solar Collector Compared With Predictions

1977 ◽  
Vol 99 (2) ◽  
pp. 169-173 ◽  
Author(s):  
J. C. McMurrin ◽  
N. A. Djordjevic ◽  
H. Buchberg
Keyword(s):  
Air Temperature ◽  
Solar Collector ◽  
Test Procedure ◽  
Ambient Air ◽  
Working Fluid ◽  
National Bureau ◽  
Fluid Temperature ◽  
Thin Wall ◽  
Cylindrical Glass ◽  
Ambient Air Temperature

A glass tube honeycomb solar collector, composed of a conventional single-glazed flat-plate water cooled nonselective black absorber with a cylindrical glass honeycomb mounted between the plate and cover glass, was designed, fabricated, and tested. The test procedure followed the National Bureau of Standards Method of Testing for Rating Solar Collectors. The honeycomb consists of individual cylindrical thin-wall glass tubes standing on end on the absorber plate in a hexagonal close-packed pattern. The tubes are 9.5-mm ID, 0.2-mm wall thickness, 5.3 length to diameter ratio made of glass with mean solar absorptive index (k), 2.6 × 10−6 μ−1, evaluated from spectral transmittance-reflectance measurements on a tubing specimen. The collector performance equalled or surpassed theoretical predictions for measurements made over a broad range of collector inlet temperatures and environmental conditions. Performance comparisons are made with a baseline double-glazed solar collector tested alongside the honeycomb collector. For applications requiring a working fluid temperature of 65°C above the ambient air temperature, honeycomb collector efficiencies of 35–55 percent may be expected for approximately a six hour period on clear days; for fluid temperature 40° C above ambient air temperature, efficiencies of 50–65 percent may be expected.

Treatment of a Municipal Leachate Under Multi-Variable Conditions

1982 ◽  
Vol 17 (1) ◽  
pp. 135-148
Author(s):  
P.T. Wong ◽  
D.S. Mavinic
Keyword(s):  
Air Temperature ◽  
Nutrient Loading ◽  
Ambient Air ◽  
Removal Rates ◽  
Ambient Air Temperature

Abstract The treatability of a municipal leachate (BOD5 = 8090 mg/L) was investigated, by aerobic biostabilization, at a nutrient loading of BOD5:N:P of 100:3.2:1.1. The first stage effluents were subsequently polished by lime-magnesium coagulation. The ranges of ambient air temperature and sludge age studied were 5° to 25°C and 5 to 20 days, respectively. In the biostabilization phase, a BOD5:N:P loading of 100:3.2:1.1 was found to be “adequate” for treatment. Organic and metal removals in the first stage units were excellent. Under all conditions investigated, except for the two units close to washout conditions (5-day sludge age units at 5° and 10°C), BOD5 and COD removals of at least 99.4 and 96.4 percent, respectively, were achieved. Similarly, removal rates for most of the metals monitored were greater than 90 percent. In general, the removal of residual contaminants was not enhanced significantly by the addition of magnesium in the lime-magnesium polishing step.

scholarly journals Ambient Air Temperature Assisted Crystallization for Inorganic CsPbI2Br Perovskite Solar Cells

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3398
Author(s):  
Yi Long ◽  
Kun Liu ◽  
Yongli Zhang ◽  
Wenzhe Li
Keyword(s):  
Solar Cells ◽  
Air Temperature ◽  
High Performance ◽  
Defect Density ◽  
Perovskite Solar Cells ◽  
Ambient Air ◽  
Dark Phase ◽  
High Quality ◽  
Ambient Air Temperature ◽  
Air Atmosphere

Inorganic cesium lead halide perovskites, as alternative light absorbers for organic–inorganic hybrid perovskite solar cells, have attracted more and more attention due to their superb thermal stability for photovoltaic applications. However, the humid air instability of CsPbI2Br perovskite solar cells (PSCs) hinders their further development. The optoelectronic properties of CsPbI2Br films are closely related to the quality of films, so preparing high-quality perovskite films is crucial for fabricating high-performance PSCs. For the first time, we demonstrate that the regulation of ambient temperature of the dry air in the glovebox is able to control the growth of CsPbI2Br crystals and further optimize the morphology of CsPbI2Br film. Through controlling the ambient air temperature assisted crystallization, high-quality CsPbI2Br films are obtained, with advantages such as larger crystalline grains, negligible crystal boundaries, absence of pinholes, lower defect density, and faster carrier mobility. Accordingly, the PSCs based on as-prepared CsPbI2Br film achieve a power conversion efficiency of 15.5% (the maximum stabilized power output of 15.02%). Moreover, the optimized CsPbI2Br films show excellent robustness against moisture and oxygen and maintain the photovoltaic dark phase after 3 h aging in an air atmosphere at room temperature and 35% relative humidity (R.H.). In comparison, the pristine films are completely converted to the yellow phase in 1.5 h.

Evaluation of the influence of ambient air temperature and air velocity on mortar cement durability using a forced convection solar dryer

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Younes Bahammou ◽  
Mounir Kouhila ◽  
Haytem Moussaoui ◽  
Hamza Lamsyehe ◽  
Zakaria Tagnamas ◽  
...  
Keyword(s):  
Environmental Factors ◽  
Forced Convection ◽  
Air Temperature ◽  
Building Materials ◽  
Ambient Air ◽  
Physical Significance ◽  
Drying Process ◽  
Air Velocity ◽  
Content Type ◽  
Ambient Air Temperature

PurposeThis work aims to study the hydrothermal behavior of mortar cement toward certain environmental factors (ambient air temperature and air velocity) based on its drying kinetics data. The objective is to provide a better understanding and controlling the stability of mortar structures, which integrate the sorption phenomenon, drying process, air pressure and intrinsic characteristics. This leads to predict the comportment of mortar structures in relation with main environmental factors and minimize the risk of cracking mortar structures at an early age.Design/methodology/approachThermokinetic study was carried out in natural and forced convection solar drying at three temperatures 20, 30 and 40°C and three air velocities (1, 3 and 5 m.s-1). The empirical and semiempirical models tested successfully describe the drying kinetics of mortar. These models simulate the drying process of water absorbed by capillarity, which is the most common humidity transfer mechanism in building materials and contain parameters with physical significance, which integrate the effect of several environmental factors and intrinsic characteristics of mortar structures.FindingsThe models simulate the drying process of water absorbed by capillarity, which is the most common humidity transfer mechanism in building materials and contain parameters with physical significance, which integrate the effect of several environmental factors and intrinsic characteristics of mortar structures. The average activation energy obtained expressed the temperature effect on the mortar diffusivity. The drying constant and the diffusion coefficient can be used to predict the influence of these environmental factors on the drying behavior of various building materials and therefore on their durability.Originality/valueEvaluation of the effect of several environmental factors and intrinsic characteristics of mortar structures on their durability.

scholarly journals Outdoor PM2.5, Ambient Air Temperature, and Asthma Symptoms in the Past 14 Days among Adults with Active Asthma

10.1289/ehp92 ◽  
2016 ◽  
Vol 124 (12) ◽  
pp. 1882-1890 ◽  
Author(s):  
Maria C. Mirabelli ◽  
Ambarish Vaidyanathan ◽  
W. Dana Flanders ◽  
Xiaoting Qin ◽  
Paul Garbe
Keyword(s):  
Air Temperature ◽  
Ambient Air ◽  
The Past ◽  
Asthma Symptoms ◽  
Ambient Air Temperature

EFFECTS OF LOW FLUCTUATING TEMPERATURES ON FARM ANIMALS.: III. INFLUENCE OF AMBIENT AIR TEMPERATURE ON FEED INTAKE OF LACTATING HOLSTEIN-FRIESIAN COWS

1958 ◽  
Vol 38 (2) ◽  
pp. 148-159 ◽  
Author(s):  
M. A. MacDonald ◽  
J. M. Bell
Keyword(s):  
Milk Production ◽  
Air Temperature ◽  
Low Temperatures ◽  
Ambient Air ◽  
Feed Consumption ◽  
Ambient Temperatures ◽  
Ambient Air Temperature ◽  
Holstein Friesian ◽  
Cent Level ◽  
Friesian Cows

This report presents effects of low temperatures on the feed consumption and efficiency of milk production of six mature, lactating, Holstein-Friesian cows that were confined in stanchions for three fortnightly experimental periods during which ambient temperatures measured in degree-hours per day (d-h/day) ranged from 110 to 1152 and daily minimum ambient air temperature (DMAAT) varied from 0° to 38°F. Applying results obtained, it was calculated that as temperatures decreased, i.e., d-h/day increased from 100 to 1200 and DMAAT decreased from 40° to 0°F, average daily intakes of total dry matter, hay, and gross and digestible Calories increased approximately 6.4 lb., 5.3 lb., 13 Therms and 9 Therms, respectively. Each of these increases was statistically significant at the 1 per cent level. Reductions in temperature also decreased gross and net caloric efficiencies of milk production approximately 10 and 8.5 per cent, respectively. These decreases were significant at the 2 per cent level. No correlation was evident between crude protein utilization and temperature.Results indicated that thermal stress was not overcome adequately by supplementary hay intake alone and that appetite stimulation by low temperatures had a carry-over effect continuing at least 24 hours. For continued efficient milk production during winters where low ambient temperatures are prevalent these results suggest it is necessary to provide some form of building insulation, ambient heat and/or provide a high energy supplement to otherwise adequate production rations.

scholarly journals Research On Solar Energy Collector With Cell Polycarbonate Absorber

2015 ◽  
Vol 1 ◽  
pp. 213
Author(s):  
Henriks Putāns ◽  
Viktorija Zagorska ◽  
Imants Ziemelis ◽  
Zanis Jesko
Keyword(s):  
Experimental Investigation ◽  
Solar Radiation ◽  
Air Temperature ◽  
Heat Carrier ◽  
Heat Insulation ◽  
Ambient Air ◽  
Maximum Temperature ◽  
Experimental Examination ◽  
Ambient Air Temperature ◽  
Flat Plate Solar Collector

A flat plate solar collector with cell polycarbonate absorber and transparent cover has been made and its experimental investigation carried out. The collector consists of a wooden box, into which, a layer of heat insulation with a mirror film and 4 mm thick cell polycarbonate sheet, as the absorber, are placed. The coherence between collector’s efficiency, heat carrier and ambient air temperature, as well as intensity of the solar radiation and heat power in the experimental investigation has been obtained. During the experimental examination the maximum temperature of the heat carrier reached 80˚C at the intensity of solar radiation about 0.8 kW/m2 and ambient air temperature around 32˚C. The efficiency of the collector reached 33-60%, depending on the intensity of solar radiation and surrounding air temperature.

The effect of ambient air temperature on cardiovascular and respiratory mortality in Thessaloniki, Greece

2019 ◽  
Vol 647 ◽  
pp. 1351-1358 ◽  
Author(s):  
Panayiotis Kouis ◽  
Maria Kakkoura ◽  
Konstantinos Ziogas ◽  
Anastasia Κ. Paschalidou ◽  
Stefania I. Papatheodorou
Keyword(s):  
Air Temperature ◽  
Ambient Air ◽  
Respiratory Mortality ◽  
Ambient Air Temperature
Sign in / Sign up

Export Citation Format

Share Document