scholarly journals Mathematical Modelling and Performance Analysis of Flat Plate Solar Dryer- CFD Simulation Approach

2021 ◽  
Vol 9 (1) ◽  
pp. 172-180
Author(s):  
Debela Geneti Desisa
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Cfd Simulation ◽  
Hot Air ◽  
Lower Temperature Range ◽  
High Turbulence ◽  
And Performance ◽  
Lower Temperature

This study focuses on the investigation of enhancing convective heat transfer between the absorber and the air inside a channel. The investigation approaches modeling different absorber through CFD simulation and validating the result with experimental data. Supplying air to both sides of the top and the bottom surfaces of the absorber increase the air mass flow rate and therefore increases the thermal efficiency of the dryer. The studies in a V-grooved absorber attain high hot air velocity; high thermal efficiency resulted from high turbulence created in the duct. For the sample taken with a flow range, 0.01kg/s to 0.06 kg/s, the high output temperature was observed in a lower temperature range and increases as the flow rate increases. At a flow rate 0.01 kg/s, the velocity of hot air passing over the V-grooved absorber attain 0.28 m/s and increased to 1.4 m/s as the mass flow rate increased to 0.06 kg/s. For the rectangular absorber, the velocity of hot air attains 0.15 m/s at a flow rate of 0.01 kg/s and increased to 1.46 m/s as the mass flow rate increases to 0.06 kg/s. The double-sided V-grooved absorber contributes 8 – 12.40% value more efficiency compared to the rectangular plate with the same flow orientation. Further investigation is recommended taking the quantitative analysis obtained in this study and generating qualitative data.

scholarly journals Off-Design Dynamic Performance Analysis of a Solar Aided Coal-Fired Power Plant

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2950
Author(s):  
Vinod Kumar ◽  
Liqiang Duan
Keyword(s):  
Power Plant ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Dynamic Performance ◽  
Feed Water ◽  
Saving Rate ◽  
Coal Consumption ◽  
Dynamic Performance Analysis

Coal consumption and CO2 emissions are the major concerns of the 21st century. Solar aided (coal-fired) power generation (SAPG) is paid more and more attention globally, due to the lesser coal rate and initial cost than the original coal-fired power plant and CSP technology respectively. In this paper, the off-design dynamic performance simulation model of a solar aided coal-fired power plant is established. A 330 MW subcritical coal-fired power plant is taken as a case study. On a typical day, three various collector area solar fields are integrated into the coal-fired power plant. By introducing the solar heat, the variations of system performances are analyzed at design load, 75% load, and 50% load. Analyzed parameters with the change of DNI include the thermal oil mass flow rate, the mass flow rate of feed water heated by the solar energy, steam extraction mass flow rate, coal consumption, and the plant thermal efficiency. The research results show that, as DNI increases over a day, the coal saving rate will also increase, the maximum coal saving rate reaches up to 5%, and plant thermal efficiency reaches 40%. It is analyzed that the SAPG system gives the best performance at a lower load and a large aperture area.

scholarly journals An experimental study of the thermal performance of the square and rhombic solar collectors

2018 ◽  
Vol 22 (1 Part B) ◽  
pp. 487-494 ◽  
Author(s):  
Aminreza Noghrehabadi ◽  
Ebrahim Hajidavaloo ◽  
Mojtaba Moravej ◽  
Ali Esmailinasab
Keyword(s):  
Experimental Study ◽  
Flat Plate ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Performance ◽  
Thermal Efficiency ◽  
Solar Collectors ◽  
Heating Systems ◽  
Solar Water Heating

Solar collectors are the key part of solar water heating systems. The most widely produced solar collectors are flat plate solar collectors. In the present study, two types of flat plate collectors, namely square and rhombic collectors are experi?mentally tested and compared and the thermal performance of both collectors is investigated. The results show both collectors have the same performance around noon (?61%), but the rhombic collector has better performance in the morning and afternoon. The values for rhombic and square collectors are approximately 56.2% and 53.5% in the morning and 56.1% and 54% in the afternoon, respectively. The effect of flow rate is also studied. The thermal efficiency of rhombic and square flat plate collectors increases in proportion to the flow rate. The results indicated the rhombic collector had better performance in comparison with the square collector with respect to the mass-flow rate.

scholarly journals On-Sun Performance Evaluation of Alternative High-Temperature Falling Particle Receiver Designs

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Clifford K. Ho ◽  
Joshua M. Christian ◽  
Julius E. Yellowhair ◽  
Kenneth Armijo ◽  
William J. Kolb ◽  
...  
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Particle Temperature ◽  
Free Fall ◽  
Mass Flow Rates ◽  
Mesh Structures ◽  
Free Falling ◽  
The Impact

This paper evaluates the on-sun performance of a 1 MW falling particle receiver. Two particle receiver designs were investigated: obstructed flow particle receiver versus free-falling particle receiver. The intent of the tests was to investigate the impact of particle mass flow rate, irradiance, and particle temperature on the particle temperature rise and thermal efficiency of the receiver for each design. Results indicate that the obstructed flow design increased the residence time of the particles in the concentrated flux, thereby increasing the particle temperature and thermal efficiency for a given mass flow rate. The obstructions, a staggered array of chevron-shaped mesh structures, also provided more stability to the falling particles, which were prone to instabilities caused by convective currents in the free-fall design. Challenges encountered during the tests included nonuniform mass flow rates, wind impacts, and oxidation/deterioration of the mesh structures. Alternative materials, designs, and methods are presented to overcome these challenges.

scholarly journals Numerical and Experimental Study of Microchannel Performance on Flow Maldistribution

Micromachines ◽  
2020 ◽  
Vol 11 (3) ◽  
pp. 323 ◽  
Author(s):  
Jojomon Joseph ◽  
Danish Rehman ◽  
Michel Delanaye ◽  
Gian Luca Morini ◽  
Rabia Nacereddine ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Experimental Studies ◽  
Wire Mesh ◽  
Pressure Losses ◽  
Macro Scale ◽  
Flow Maldistribution

Miniaturized heat exchangers are well known for their superior heat transfer capabilities in comparison to macro-scale devices. While in standard microchannel systems the improved performance is provided by miniaturized distances and very small hydraulic diameters, another approach can also be followed, namely, the generation of local turbulences. Localized turbulence enhances the heat exchanger performance in any channel or tube, but also includes an increased pressure loss. Shifting the critical Reynolds number to a lower value by introducing perturbators controls pressure losses and improves thermal efficiency to a considerable extent. The objective of this paper is to investigate in detail collector performance based on reduced-order modelling and validate the numerical model based on experimental observations of flow maldistribution and pressure losses. Two different types of perturbators, Wire-net and S-shape, were analyzed. For the former, a metallic wire mesh was inserted in the flow passages (hot and cold gas flow) to ensure stiffness and enhance microchannel efficiency. The wire-net perturbators were replaced using an S-shaped perturbator model for a comparative study in the second case mentioned above. An optimum mass flow rate could be found when the thermal efficiency reaches a maximum. Investigation of collectors with different microchannel configurations (s-shaped, wire-net and plane channels) showed that mass flow rate deviation decreases with an increase in microchannel resistance. The recirculation zones in the cylindrical collectors also changed the maldistribution pattern. From experiments, it could be observed that microchannels with S-shaped perturbators shifted the onset of turbulent transition to lower Reynolds number values. Experimental studies on pressure losses showed that the pressure losses obtained from numerical studies were in good agreement with the experiments (<4%).

Influence of Steam Injection on Thermal Efficiency and Operating Temperature of GE-F5 Gas Turbines Applying VODOLEY System

2005 ◽  
Author(s):  
Mohsen Ghazikhani ◽  
Nima Manshoori ◽  
Davood Tafazoli
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Steam Injection ◽  
Gas Turbine Cycle

An industrial gas turbine has the characteristic that turbine output decreases on hot summer days when electricity demand peaks. For GE-F5 gas turbines of Mashad Power Plant when ambient temperature increases 1° C, compressor outlet temperature increases 1.13° C and turbine exhaust temperature increases 2.5° C. Also air mass flow rate decreases about 0.6 kg/sec when ambient temperature increases 1° C, so it is revealed that variations are more due to decreasing in the efficiency of compressor and less due to reduction in mass flow rate of air as ambient temperature increases in constant power output. The cycle efficiency of these GE-F5 gas turbines reduces 3 percent with increasing 50° C of ambient temperature, also the fuel consumption increases as ambient temperature increases for constant turbine work. These are also because of reducing in the compressor efficiency in high temperature ambient. Steam injection in gas turbines is a way to prevent a loss in performance of gas turbines caused by high ambient temperature and has been used for many years. VODOLEY system is a steam injection system, which is known as a self-sufficient one in steam production. The amount of water vapor in combustion products will become regenerated in a contact condenser and after passing through a heat recovery boiler is injected in the transition piece after combustion chamber. In this paper the influence of steam injection in Mashad Power Plant GE-F5 gas turbine parameters, applying VODOLEY system, is being observed. Results show that in this turbine, the turbine inlet temperature (T3) decreases in a range of 5 percent to 11 percent depending on ambient temperature, so the operating parameters in a gas turbine cycle equipped with VODOLEY system in 40° C of ambient temperature is the same as simple gas turbine cycle in 10° C of ambient temperature. Results show that the thermal efficiency increases up to 10 percent, but Back-Work ratio increases in a range of 15 percent to 30 percent. Also results show that although VODOLEY system has water treatment cost but by using this system the running cost will reduce up to 27 percent.

Evaluation of Effects of Different Design Parameters on Axial Fan Performance Using CFD

2015 ◽  
Author(s):  
Racheet Matai ◽  
Savas Yavuzkurt
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cfd Simulation ◽  
Chord Length ◽  
Design Parameters ◽  
Axial Fan ◽  
Blade Length ◽  
Resistor Networks ◽  
Mass Flow Rates

The performance of an industrial fan was simulated using CFD and results were compared with the experimental data. The fan is used to cool a row of resistor networks which dissipate excess energy generated by regenerative power in an inverter application. It has a diameter of 24 inches (0.6096m) and rotates at different speeds ranging from 2500 to 3900 RPM depending on the requirements. CFD simulation results were also verified by simulating performance of the same fan at different speeds and comparing the results with what was expected from fan affinity laws. The CFD results matched almost exactly (with ∼0.2% difference for pressure at a given flow rate) with the performance being predicted by the affinity laws. The effect of variation of different parameters such as the blade length, number of blades, and blade chord length was studied. Increasing the blade length at the same RPM increased the mass flow rate (by ∼17%) for the same pressure. Increasing the chord length while keeping the same number of blades, at a given RPM, made the performance curve (pressure versus flow rate, i.e. PV curve) steeper and blades stalled at a higher mass flow rate (8.77 kg/sec compared to the previous 8.44 kg/sec). For the same total blade surface area, less number of blades with longer chords stalled at lower mass flow rates (9.22 kg/sec for a 33% shorter chord and 36 blades compared to 8.3 kg/sec for the original rotor which had 24 blades).

CFD Simulation of Passive Containment Cooling System in Hot Leg SB-LOCA for 1000MW PWR

2017 ◽  
Author(s):  
Jingya Li ◽  
Xiaoying Zhang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cfd Simulation ◽  
Driving Forces ◽  
Cooling System ◽  
Large Mass ◽  
Internal Cooling ◽  
Vapor Injection ◽  
The Difference

The passive cooling system (PCCS) for reactor containment is a security system that can be used to cool the atmosphere and reduce pressure inside of containment in case of temperature and pressure increase caused by vapor injection, which requires no external power because it works only with natural forces. However, as the driving forces from natural physical phenomena are of low amplitude, uncertainties and instabilities in the physical process can cause failure of the system. This article aims to establish a CFD simulation model for the Passive Containment Cooling System of 1000MW PWR using Code_Saturne and FLUENT software. The comparison of 4 different models based respectively on mixture model, COPAIN test, Uchida correlation and Chilton-Colburn analogy which simulate the condensing effect and the improvement of source code are based on a 3D simulation of PCCS system. To simulate the thermal-hydraulic condition in the containment after LOCA accident caused by a double-ended main pipe rupture, a high temperature vapor with the given mass flow rate are supposed to be the source of energy and mass into containment. Meanwhile the surface of three condensing island applies the wall condensation model. The simulation results show similar transient process obtained with the 4 models, while the difference between the transient simulation and the steady-state analysis of three models is less than 3%. The large mass flow rate of water loss status inside the containment cause a high flow rate of vapor which could be uniformly mixed with air in a short time. For the self-condensing efficiency of 3 groups of PCCS system, the non-centrosymmetric injection position resulting that the condensing efficiency is slightly higher for the two heat exchanger groups nearby. During the first 2400s of simulation time, more than 75.69% of the vapor is condensed, indicating that for the occurrence of condensation at the wall mainly driven by natural convection, the effect of thermodynamic siphon could improve the flow of gas mixture inside the tubes when the velocity of mixture is not large enough, so that the vapor could smoothly enter the tube and reach the internal cooling surface then to be condensed. Besides, PCCS ensure the containment internal pressure maintained below 2 bar and the temperature maintained below 380K during 3600s.

CFD Simulation of Gas Distributor with Two Chambers

2014 ◽  
Vol 989-994 ◽  
pp. 2264-2267
Author(s):  
Dong Fang Zhao ◽  
Feng Guo Liu
Keyword(s):  
Natural Gas ◽  
Mass Flow Rate ◽  
Turbulence Model ◽  
Mass Flow ◽  
Flow Rate ◽  
Cfd Simulation ◽  
Second Order ◽  
Gas Distributor ◽  
New Type ◽  
Simulation Results

This paper investigated a new type of gas distributor with two chambers by CFD software. The distributor has a natural gas inlet and nine nozzle outlets. For the investigation of this project, the mass flow rate of the distributor was analyzed in this paper to provide a way to optimize the structure of distributor. The N-S equations approached with the RNG k-ε turbulence model and the discretization were employed second order upwind. The simulation results will provide a number of useful suggestions and references for the further design.

Modeling on the Effect of Imbalance Burner Pressure and Mass Flow Rate in a Full-Scale Gas Fired Industrial Boiler

2003 ◽  
Author(s):  
Hasril Hasini ◽  
Mohd. Zamri Yusoff ◽  
Kamsani Abdul Majid ◽  
Mohd. Rizal Ramli ◽  
Hamdan Hassan ◽  
...  
Keyword(s):  
Temperature Distribution ◽  
Flow Pattern ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cfd Simulation ◽  
Combustion Process ◽  
General Purpose ◽  
Anticlockwise Direction ◽  
Industrial Boiler

CFD simulation of the combustion process in a 120MW gas fired industrial boiler has been performed, with focus on the flow pattern and temperature distribution at the reheater section in the furnace. The modeling was done using general-purpose CFD software, CFD-ACE+ developed by CFD Research Corporation. The effect of imbalance burner pressure is simulated by varying the mass flow rate of fuel (natural gas) injected at each burner. The simulation result shows good qualitative agreement with practical observation. The flow in the furnace is highly swirling with intense mixing and follows a helical pattern in an anticlockwise direction. Temperature distribution prior to entry to the reheater is significantly higher on the right side of the reheater. As a conclusion, the imbalance nozzles pressure creates uneven mass flow rate of air and fuel, which results in asymmetric flow pattern and temperature distribution at the reheater section.

scholarly journals Efficiency Enhancement in Double-Pass Perforated Glazed Solar Air Heaters with Porous Beds: Taguchi-Artificial Neural Network Optimization and Cost–Benefit Analysis

2021 ◽  
Vol 13 (21) ◽  
pp. 11654
Author(s):  
Roozbeh Vaziri ◽  
Akeem Adeyemi Oladipo ◽  
Mohsen Sharifpur ◽  
Rani Taher ◽  
Mohammad Hossein Ahmadi ◽  
...  
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Exergy Efficiency ◽  
Wire Mesh ◽  
Double Pass ◽  
Artificial Neural

Analyzing the combination of involving parameters impacting the efficiency of solar air heaters is an attractive research areas. In this study, cost-effective double-pass perforated glazed solar air heaters (SAHs) packed with wire mesh layers (DPGSAHM), and iron wools (DPGSAHI) were fabricated, tested and experimentally enhanced under different operating conditions. Forty-eight iron pieces of wool and fifteen steel wire mesh layers were located between the external plexiglass and internal glass, which is utilized as an absorber plate. The experimental outcomes show that the thermal efficiency enhances as the air mass flow rate increases for the range of 0.014–0.033 kg/s. The highest thermal efficiency gained by utilizing the hybrid optimized DPGSAHM and DPGSAHI was 94 and 97%, respectively. The exergy efficiency and temperature difference (∆T) indicated an inverse relationship with mass flow rate. When the DPGSAHM and DPGSAHI were optimized by the hybrid procedure and employing the Taguchi-artificial neural network, enhancements in the thermal efficiency by 1.25% and in exergy efficiency by 2.4% were delivered. The results show the average cost per kW (USD 0.028) of useful heat gained by the DPGSAHM and DPGSAHI to be relatively higher than some double-pass SAHs reported in the literature.

Sign in / Sign up

Export Citation Format

Share Document