Numerical analysis of three-dimensional wall-jet using anisotropic turbulence model

2013 ◽  
Author(s):  
Keiichi Ishiko ◽  
Atsushi Hashimoto ◽  
Yuichi Matsuo ◽  
Akira Yoshizawa
Keyword(s):  
Numerical Analysis ◽  
Turbulence Model ◽  
Three Dimensional ◽  
Wall Jet ◽  
Anisotropic Turbulence

Comparison of Various RANS Models for Impinging Round Jet Cooling From a Cylinder

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Ketan Atulkumar Ganatra ◽  
Dushyant Singh
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Turbulence Model ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Jet Impingement ◽  
Target Surface ◽  
Point Of View ◽  
Nozzle Diameter ◽  
Round Jet

The numerical analysis for the round jet impingement over a circular cylinder has been carried out. The v2f turbulence model is used for the numerical analysis and compared with the two equation turbulence models from the fluid flow and the heat transfer point of view. Further, the numerical results for the heat transfer with original and modified v2f turbulence model are compared with the experimental results. The nozzle is placed orthogonally to the target surface (heated cylindrical surface). The flow is assumed as the steady, incompressible, three-dimensional and turbulent. The spacing between the nozzle exit and the target surface ranges from 4 to 15 times the nozzle diameter. The Reynolds number based on the nozzle diameter ranges from 23,000 to 38,800. From the heat transfer results, the modified v2f turbulence model is better as compared to the other turbulence models. The modified v2f turbulence model has the least error for the numerical Nusselt number at the stagnation point and wall jet region.

Evaluation of an Anisotropic Turbulence Model for Simulation of Three-dimensional Cases

2020 ◽  
Author(s):  
Leonardo Machado da Rosa ◽  
Daniela Koerich ◽  
Tommaso Oggian ◽  
Henry França Meier
Keyword(s):  
Turbulence Model ◽  
Three Dimensional ◽  
Anisotropic Turbulence

Three dimensional numerical analysis of heat transfer during spray quenching of 22MnB5 steel with a single nozzle

2020 ◽  
Author(s):  
Emre Bulut ◽  
Gökhan Sevilgen ◽  
Ferdi Eşiyok ◽  
Ferruh Öztürk ◽  
Tuğçe Turan Abi
Keyword(s):  
Heat Transfer ◽  
Numerical Analysis ◽  
Three Dimensional ◽  
22Mnb5 Steel

Numerical Study of the Mean and Filtered Characteristics of Turbulent Jets Impinging on Convex and Flat Surfaces Using LES

2012 ◽  
Author(s):  
Adra Benhacine ◽  
Zoubir Nemouchi ◽  
Lyes Khezzar ◽  
Nabil Kharoua
Keyword(s):  
Convex Surface ◽  
Numerical Study ◽  
Three Dimensional ◽  
Turbulent Jets ◽  
Scale Model ◽  
Wall Jet ◽  
Potential Core ◽  
Flat Surfaces ◽  
Free Jet ◽  
Eddy Simulation

A numerical study of a turbulent plane jet impinging on a convex surface and on a flat surface is presented, using the large eddy simulation approach and the Smagorinski-Lilly sub-grid-scale model. The effects of the wall curvature on the unsteady filtered, and the steady mean, parameters characterizing the dynamics of the wall jet are addressed in particular. In the free jet upstream of the impingement region, significant and fairly ordered velocity fluctuations, that are not turbulent in nature, are observed inside the potential core. Kelvin-Helmholtz instabilities in the shear layer between the jet and the surrounding air are detected in the form of wavy sheets of vorticity. Rolled up vortices are detached from these sheets in a more or less periodic manner, evolving into distorted three dimensional structures. Along the wall jet the Coanda effect causes a marked suction along the convex surface compared with the flat one. As a result, relatively important tangential velocities and a stretching of sporadic streamwise vortices are observed, leading to friction coefficient values on the curved wall higher than those on the flat wall.

Optimization of the Navy’s three-dimensional mine impact burial prediction simulation model, Impact35, using high-order numerical methods

2021 ◽  
pp. 154851292110286
Author(s):  
Athanasios Donas ◽  
Ioannis Famelis ◽  
Peter C Chu ◽  
George Galanis
Keyword(s):  
Numerical Analysis ◽  
Numerical Methods ◽  
Prediction Model ◽  
Simulation Model ◽  
Three Dimensional ◽  
Simulation System ◽  
High Order ◽  
Alternative Methodology ◽  
Runge Kutta ◽  
Fifth Order

The aim of this paper is to present an application of high-order numerical analysis methods to a simulation system that models the movement of a cylindrical-shaped object (mine, projectile, etc.) in a marine environment and in general in fluids with important applications in Naval operations. More specifically, an alternative methodology is proposed for the dynamics of the Navy’s three-dimensional mine impact burial prediction model, Impact35/vortex, based on the Dormand–Prince Runge–Kutta fifth-order and the singly diagonally implicit Runge–Kutta fifth-order methods. The main aim is to improve the time efficiency of the system, while keeping the deviation levels of the final results, derived from the standard and the proposed methodology, low.

scholarly journals Air Ventilation Performance of School Classrooms with Respect to the Installation Positions of Return Duct

2021 ◽  
Vol 13 (11) ◽  
pp. 6188
Author(s):  
Sungwan Son ◽  
Choon-Man Jang
Keyword(s):  
Air Quality ◽  
Numerical Analysis ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Three Dimensional ◽  
Cross Infection ◽  
School Students ◽  
Height Range ◽  
Air Ventilation ◽  
Ventilation Performance

For students, who spend most of their time in school classrooms, it is important to maintain indoor air quality (IAQ) to ensure a comfortable and healthy life. Recently, the ventilation performance for indoor air quality in elementary schools has emerged as an important social issue due to the increase in the number of days of continuous high concentrations of particulate matter. Three-dimensional numerical analysis has been introduced to evaluate the indoor airflow according to the installation location of return diffusers. Considering the possibility of the cross-infection of infectious diseases between students due to the direction of airflow in the classroom, the airflow angles of the average respiratory height range of elementary school students, between 1.0 and 1.5 m, are analyzed. Throughout the numerical analysis inside the classroom, it is found that the floor return system reduces the indoor horizontal airflow that causes cross-infection among students by 20% compared to the upper return systems. Air ventilation performance is also analyzed in detail using the results of numerical simulation, including streamlines, temperature and the age of air.

Sign in / Sign up

Export Citation Format

Share Document