scholarly journals Analisis Tebal Lapis Perkerasan Jalan dengan Meninjau Sifat Fisik Agregat Lapis Fondasi Bawah pada Ruas Jalan Sofi-Wayabula Pulau Morotai. (Hal. 97-107)

2019 ◽  
Vol 5 (3) ◽  
pp. 97
Author(s):  
Nurul Fauziah Endah Ningtyas ◽  
Samun Haris
Keyword(s):  
Road Construction ◽  
Flexible Pavement ◽  
Relative Strength ◽  
Strength Coefficient ◽  
The Road ◽  
Human Needs ◽  
Road Pavement ◽  
Calculation Results ◽  
Pavement Structures ◽  
Base Course

ABSTRAKJalan sebagai sarana penunjang transportasi darat memiliki peran penting untuk memenuhi kebutuhan manusia. Salah satu material penting dalam pembuatan jalan adalah agregat. Sifat fisik agregat menjadi salah satu faktor penentu tebal lapisan struktur perkerasan. Ruas jalan Sofi–Wayabula adalah ruas jalan nasional strategis di Pulau Morotai dengan menggunakan perkerasan lentur. Agregat yang digunakan untuk lapis fondasi bawah pada ruas jalan ini adalah kombinasi agregat Eks. Palu dengan agregat Eks. Morotai. Tujuan dari penelitian ini adalah untuk menganalisis tebal lapis fondasi bawah berdasarkan koefisien kekuatan relatif ( ) yang didapat dari nilai CBR kombinasi agregat Eks. Palu dengan agregat Eks. Morotai dan agregat Eks. Palu pada struktur perkerasan lentur. Dari hasil perhitungan metode Manual Perkerasan Jalan 2017 didapatkan tebal lapis fondasi bawah sebesar 15 cm, bernilai sama, baik menggunakan kombinasi agregat Eks. Palu dengan agregat Eks. Morotai, maupun agregat Eks. Palu. Sedangkan, dengan menggunakan Pedoman Perkerasan Jalan Lentur 2011 didapat tebal lapis fondasi bawah sebesar 15,054 cm untuk kombinasi agregat Eks. Palu dengan agregat Eks. Morotai dan 14,608 cm untuk agregat Eks. Palu.Kata Kunci: perkerasan lentur, koefisien kekuatan relatif, lapis fondasi bawah. ABSTRACTRoads as a means of supporting land transportation have an important role to meet human needs. One of important material in road construction is aggregate. The aggregate physical properties become one of the determinants of the pavement thickness structure layer. The road segment of Sofi-Wayabula is a strategic national road in Morotai Island by using flexible pavement. The aggregate used for the sub-base course of the road is combination of aggregate Ex. Palu with Ex. Morotai aggregate. The purpose of this research is to analyze the thickness of the sub-base course based on relative strength coefficient  (a3) obtained from the value of CBR combination of aggregate Ex. Palu with Ex. Morotai aggregate and aggregate Ex. Palu on flexible pavement structures. From the calculation results of the Pavement Road Manual method 2017, the thick of sub-base course is 15 cm, have equal value using the combination of Ex. Palu aggregate with Ex. Morotai aggregate or the Ex.Palu aggregate. Meanwhile, by using Flexible Road Pavement Guideline 2011 the thickness of the sub-base course is 15,054 cm for combination of Ex.Palu aggregate with Ex. Morotai aggregate and 14,608 cm for Ex.Palu.Keywords: flexible pavement, relative strength coefficient, sub-base course.

scholarly journals ANALISIS PERKERASAN LENTUR DI ATAS TANAH EKSPANSIF

2019 ◽  
Vol 2 (1) ◽  
pp. 48-57
Author(s):  
Mukhlis Mukhlis ◽  
Yuhanis Yunus ◽  
Sofyan M. Saleh
Keyword(s):  
Expansive Soil ◽  
Flexible Pavement ◽  
Allowable Limit ◽  
The Road ◽  
Road Pavement ◽  
Swell Potential ◽  
Pavement Structure ◽  
Pavement Structures ◽  
On The Road ◽  
Base Soil

The segmented road of Bireuen-Takengon has often damaged in apart of its pavement structure due to the area of flexible pavement structure taken place upon an expansive soil that leads to depreciation caused by the influence of changes in the water level. The aim of this research method was to analyze the characteristics of the base soil underlying the pavement and to analyze the flexible pavement structure in the widening of the road. The observed area was Sta.70+175 s/d Sta.74+925 which taken place in Bener Meriah regency, sub-district of Timang Gajah. The results of USCS clarification show that the road of basal soil is included in the MH OH with a PI value of 25.42%, LL 64.25% with a potential level of development and activity belonging to the medium-high category and also having mineral types of Illite. From the analysis of KENPAVE software, the design of flexible pavement structures is based on data planning that has a maximum stress and deflection value, on the base soil, of 0.1814 kg/cm2 and 0.0585 cm respectively. Moreover, based on Job mix data the maximum value of stress and deflection is 0.2444 kg/cm2 and 0.0585 cm respectively in which both of two stress and deflections are within the allowable limit; which both of two stress and deflections are within the allowable limit; 7.8 kg/cm2 and 2.5 cm. The evaluation results of both data are feasible to be used as an improved design on the pavement as the pressure generated by the weight of the road pavement structure is 1.949 kg/cm2, while the swell pressure that occurs on subgrade is 1.805 kg/cm2. Hence, The flexible pavement structure on the road segment is still able to reduce the swell potential on expansive soil.

Desain Perkerasan Jalan Sumberboto - Gununggede Blitar Menggunakan Metode Manual Desain

2021 ◽  
Vol 4 (2) ◽  
pp. 186
Author(s):  
Uminarsih Uminarsih ◽  
Yosef Cahyo Setianto Poernomo ◽  
Agata Iwan Candra ◽  
Fajar Romadhon
Keyword(s):  
Road Construction ◽  
Bottom Layer ◽  
Flexible Pavement ◽  
The Road ◽  
Total Budget ◽  
Road Pavement ◽  
Road Users ◽  
Road Section ◽  
Beach Tourism ◽  
On The Road

The road is an access that connects an area with other areas. With the road, mobility will be easier so that it has an impact on increasing or stabilizing the economy. The Sumberboto-Gunung Gede Blitar road section is one of the access roads to Tambakrejo beach tourism. To improve comfort and safety for road users, it is necessary to improve road quality. This study aims to plan the pavement on the Sumberboto-Gunung Gede Blitar road section. The planning is carried out on the condition of the heavily damaged pavement, with a service life of more than 10 years, the width of the road is 4 meters, the length of the road is 6 kilometers, the type of collector road is class II, and the type of pavement is laston. The planning carried out includes the addition of roads in the hills of Blitar Regency, the data used includes the condition of the sections on the road with calculations referring to the Design Manual Number 02/M/BM/2013 road pavement. The planning results obtained road construction with flexible pavement, with a specification of a surface layer of 10 cm, a layer of 20 cm for the top foundation, 25 cm for the bottom layer of the foundation. From this plan, a total budget of Rp. 13,572,808,084.00 (thirteen billion five hundred seventy-two million eight hundred thousand rupiah) is required. With these results, it can be used as a reference in realizing road construction on the Sumberboto-Gunung Gede Blitar road section.

Mechanical effects and paradoxical phenomena in the thermoelastic stress of the road pavement structures

2018 ◽  
pp. 128-145
Author(s):  
Volodynyr Mozghovyi ◽  
◽  
Viktor Gaidaichuk ◽  
Yurii Zaiets ◽  
Liudmyla Shevchuk ◽  
...  
Keyword(s):  
Thermoelastic Stress ◽  
The Road ◽  
Mechanical Effects ◽  
Road Pavement ◽  
Pavement Structures

scholarly journals Research on the Properties of Mineral–Cement Emulsion Mixtures Using Recycled Road Pavement Materials

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 563
Author(s):  
Łukasz Skotnicki ◽  
Jarosław Kuźniewski ◽  
Antoni Szydło
Keyword(s):  
Road Construction ◽  
Base Layer ◽  
Asphalt Emulsion ◽  
Reclaimed Asphalt ◽  
Pavement Materials ◽  
Road Pavement ◽  
Road Surfaces ◽  
Cement Binder ◽  
Pavement Structures ◽  
By Products

The reduction in natural resources and aspects of environmental protection necessitate alternative uses of waste materials in the area of construction. Recycling is also observed in road construction where mineral–cement emulsion (MCE) mixtures are applied. The MCE mix is a conglomerate that can be used to make the base layer in road pavement structures. MCE mixes contain reclaimed asphalt from old, degraded road surfaces, aggregate improving the gradation, asphalt emulsion, and cement as a binder. The use of these ingredients, especially cement, can cause shrinkage and cracks in road layers. The article presents selected issues related to the problem of cracking in MCE mixtures. The authors of the study focused on reducing the cracking phenomenon in MCE mixes by using an innovative cement binder with recycled materials. The innovative cement binder based on dusty by-products from cement plants also contributes to the optimization of the recycling process in road surfaces. The research was carried out in the field of stiffness, fatigue life, crack resistance, and shrinkage analysis of mineral–cement emulsion mixes. It was found that it was possible to reduce the stiffness and the cracking in MCE mixes. The use of innovative binders will positively affect the durability of road pavements.

scholarly journals The Limestone as a Materials Combination of Base Course on the Road Pavement

2021 ◽  
Vol 1125 (1) ◽  
pp. 012019
Author(s):  
Yosef Cahyo Setianto Poernomo ◽  
Sigit Winarto ◽  
Zendy Bima Mahardana ◽  
Dwifi Aprillia Karisma ◽  
Rekso Ajiono
Keyword(s):  
The Road ◽  
Road Pavement ◽  
Base Course ◽  
On The Road

Use of soils and recycled industrial products treated with water glass in the road pavement base courses

2021 ◽  
Vol 2021 ◽  
pp. 86-93
Author(s):  
Anatolii Mudrychenko ◽  
◽  
Andrii Hrinchuk ◽  
Ivan Balashov ◽  
Sergey Illyasch ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Sodium Silicate ◽  
Water Glass ◽  
Water Solution ◽  
Road Construction ◽  
The Road ◽  
Road Pavement ◽  
Stone Materials ◽  
Pavement Base ◽  
Local Materials

Introduction. Growing volumes of road construction increase the need to expand and rationally use of raw materials. The need for stone materials can be solved through the wide spread using of local materials, recycled products of industry in the pavement base courses and decreasing the use of natural construction materials by replacing them with alternatives, including soils, slag materials that are metallurgical industry wastes. Experience of ferrous metallurgy slag usage has been accumulated in the road industry of Ukraine. Their usage makes it possible to extend the construction season, increases the strength and reliability of road structures due to their physical and mechanical properties, significantly reduces the road pavement energy consumption, simplifying the technology of works and the estimated cost of road construction. It was determined that the layers of pavement made from blast furnace slag have a high bearing capacity. Slag structures in 5–10 years of hardening are not inferior to, and in 10–20 years surpass cement structures on durability and deformation resistance. However, there is an urgent need to provide strength and open road traffic on the already built road section in a shortest possible term, so there is a need to accelerate the activation of the slow-setting binder. Therefore water glass (water solution of sodium silicate) is used.Purpose. The purpose of the work is to study the feasibility of using the soils and recycled industry products treated with water glass in the road pavement base courses.Materials and methods. Experimental tests of soils and blast furnace slags treated with water glass with different content of water solution of sodium silicate were performed.Results. The feasibility of using the asphalt concrete mixtures on the basis of soils and recycled products of industry treated with water glass in the pavement base courses is determined. Recommendations regarding technological parameters of preparation, transportation, laying and compaction of such mixes are given.Conclusions. Performed studies have shown that the physical and mechanical parameters of soils and blast furnace slags treated with water glass meet the requirements of current regulations of Ukraine. The advantages of use are noted, namely: the possibility of replacement of traditional stone materials by the local materials and recycled products of industry, reducing the transport component in the cost of construction. The obtained results indicate the feasibility of using the soils and recycled products of industry treated with water glass in the road construction.Keywords: soils, recycled products of industry, graded blast furnace slag, water solution of sodium silicate, water glass

scholarly journals STUDI PERBANDINGAN MENGENAI PERHITUNGAN BESARAN REGANGAN DI LAPISAN SUBGRADE AKIBAT BEBAN RODA KENDARAAN UNTUK JALAN RAYA KELAS I

2020 ◽  
Vol 3 (4) ◽  
pp. 1077
Author(s):  
Leonardo Lijuwardi ◽  
Gregorius Sandjaja Sentosa
Keyword(s):  
Flexible Pavement ◽  
Layer System ◽  
The Road ◽  
Strain Calculation ◽  
Road Pavement ◽  
Large Contact Area ◽  
Vehicle Loads ◽  
Pavement Layers ◽  
Road Data ◽  
Pavement Thickness

ABSTRACTMulti-layer systems theory is one of the concepts used in finding out the amount of strain and stress that occurs in the road pavement system due to vehicle loads. The purpose and goal of this study is to analyze the amount of strain that occurs on the pavement systems in Indonesia, especially in the subgrade position. The type of multi-layer system theory used to calculate the amount of strain includes the theory of one layer systems, two-layer systems and three-layer systems with data analyzed in the form of pavement thickness and type of pavement material.Based on this study, the value of strain obtained by the theory of one-layer system in some of the road data reviewed are 533.8658 microstrains, 361.3456 microstrains, 1577.987601 microstrains, 618,012 microstrains and 140.3075 microstrains. For research with two-layers systems, the results obtained are 1116.2920 microstrains, 544.322 microstrains, 1448.0839 microstrains, 734.1844 microstrains and 738.7226 microstrains. For research with three-layers system, results obtained are 72.20275278; 70.80346908; 192.9638366; 123.1150377dan 391.8845636 microstrains. The results with the calculation of one-layer system are very large because the modulus values of the subgrade layers are not reviewed and only pavement thickness is reviewed. As for calculations with the theory of two-layer systems, the results obtained are far greater than one-layer systems, due to the limitations of the graph to find the value of the ratio between thickness and large contact area. Calculation with the theory of three-layers system is a strain calculation which has a much smaller value compared to the theory of one-layer system and two- layer system. This is because this theory divides the calculated pavement layers into three layers, which is in accordance with the flexible pavement system which divides the pavement layers into three layers, so this calculation is the most ideal calculation because it approaches its original condition.ABSTRAKTeori sistem lapis banyak merupakan salah satu konsep yang digunakan dalam mencari tahu besaran regangan dan tegangan yang terjadi pada sistem perkerasan jalan raya akibat beban kendaraan. Maksud dan tujuan dari penelitian ini adalah untuk menganalisis mengenai besaran regangan yang terjadi pada jalan raya di Indonesia pada lapisan tanah dasar khususnya di posisi permukaan tanah dasar. Adapun jenis teori sistem lapis banyak yang digunakan untuk menghitung besaran regangan tersebut antara lain teori one-layer systems, two-layers systems dan three-layers systems dengan data yang dianalisis berupa tebal perkerasan dan jenis material perkerasan jalan.Berdasarkan penelitian ini, adapun nilai dari regangan yang diperoleh dengan teori one-layer system di beberapa data jalan yang ditinjau, antara lain 533.8658 mikrostrain, 361.3456 mikrostrain, 1577.987601 mikrostrain, 618.012 mikrostrain dan 140.3075 mikrostrain. Untuk penelitian dengan two-layers system diperoleh hasil yaitu 1116.2920 mikrostrain, 544.322 mikrostrain, 1448.0839 mikrostrain, 734.1844 mikrostrain dan 738.7226 mikrostrain. Untuk penelitian dengan three-layers system diperoleh hasil antara lain 72.20275278; 70.80346908; 192.9638366; 123.1150377 dan 391.8845636 mikrostrain. Hasil dengan perhitungan one-layer system sangat besar dikarenakan nilai modulus lapisan dari subgrade tidak ditinjau dan hanya meninjau tebal perkerasan. Adapun untuk perhitungan dengan teori two-layers system, hasil yang diperoleh jauh lebih besar daripada one-layer system, yang disebabkan keterbatasan dari grafik untuk mencari nilai perbandingan antara ketebalan dan luas kontak yang besar. Perhitungan dengan teori three-layers system merupakan perhitungan regangan yang memiliki nilai jauh lebih kecil dibandingkan dengan teori one-layer system dan two-layer systems. Hal ini dikarenakan teori ini membagi lapisan perkerasan yang dihitung menjadi tiga buah lapisan, yang sesuai dengan sistem perkerasan lentur yang membagi lapisan perkerasan menjadi tiga buah lapisan, sehingga perhitungan ini merupakan perhitungan yang paling ideal karena mendekati kondisi aslinya.

scholarly journals Application of deflection bowl parameters for assessing different structures of road pavement

2018 ◽  
Vol 195 ◽  
pp. 04002
Author(s):  
Bagus Hario Setiadji
Keyword(s):  
Careful Consideration ◽  
Ease Of Use ◽  
Popular Method ◽  
The Road ◽  
Road Pavement ◽  
Evaluation Procedures ◽  
Layer Characteristic ◽  
Subgrade Modulus ◽  
Pavement Structures ◽  
Structural Layer

To date, non-destruction testing (NDT) method is the most popular method to assess the condition of road pavement. Among all evaluation procedures of the NDT method, load-deflection backcalculation analysis is one that is developed widely to understand the structural behavior of road pavement. On one side, the use of this analysis is greatly beneficial for presenting the layer characteristic accurately. However, the analysis requires specialist expertise. To overcome this, deflection bowl parameter application could become one alternative. The parameters are very easy to use; however, the intention of the parameters so far is only as an indication of the condition of the structural layer of the road pavement. Therefore, the parameters have to be used with careful consideration. In this study, the parameters were evaluated to determine the optimal usage of the parameters against different structures of road pavements. The results showed that a simplification of the number of parameters and a reformulation of the parameters were required by taking into account the ease of use in practice, the accuracy of subgrade modulus determination and the possibility to evaluate pavement structures with a layer number less than four.

scholarly journals SERAT ECENG GONDOK SEBAGAI BAHAN ALTERNATIF ADMIXTURE PADA LASTON TIPE XI SNI 03-1737-1989 DITINJAU TERHADAP NILAI-NILAI UJI MARSHALL

Jurnal CIVILA ◽  
2018 ◽  
Vol 3 (2) ◽  
pp. 154
Author(s):  
Errine Yulia Rizqi Intanti ◽  
Zulkifli Lubis
Keyword(s):  
Water Hyacinth ◽  
Asphalt Mixture ◽  
Road Construction ◽  
Flexible Pavement ◽  
The Road ◽  
Concrete Layer ◽  
Wide Range ◽  
On The Road ◽  
Marshall Stability

In Indonesia, the road construction has experienced a fairly good development. From a wide range of road constructions, flexible pavement is the most chosen one because its characteristics: easy, fast, and efficient. However, flexible pavement has many weaknesses, for example the premature damage on the road surface after some time passed by the traffic so that the road cannot reach the planned age. For that, it is done a research to add a hot asphalt mixture material that aims to improve the quality of the mixture results. The selected ingredient is natural water hyacinth. The method used is trial and error with reference of SNI 03-1737-1989. Variations used are 2%, 4%, 6%, 8% and 10% of the asphalt weight, asphalt level used is 5.72 %. Of the 5 variations of mixture used on Type XI Asphalt Concrete Layer, it is obtained the result that the water hyacinth fiber level which has the best score and meet the specifications of SNI 03-1737-1989 is on the percentage of 6% which obtained from calculation data using graphs and regression model where Marshall Stability is equal to 644,46 Kg, flow 3,39 mm, VMA (voids in the mineral aggregate) is equal to 13,83 %, VFWA (voids filled with asphalt) is equal to 65,35%, VIM (voids in the mix) is equal to 2,52 %, density of 2.31 gr/cc, and Marshall Quotient of 164.03 Kg / mm.

Sign in / Sign up

Export Citation Format

Share Document