scholarly journals STUDI KUAT LENTUR BETON DENGAN BAHAN TAMBAH SERAT ABAKA

Teras Jurnal ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 53
Author(s):  
Yudi Pranoto ◽  
Lina Halim ◽  
Anung Sudibyo
Keyword(s):  
Flexural Strength ◽  
Bending Strength ◽  
Fiber Content ◽  
Mix Design ◽  
Fine Aggregate ◽  
Test Results ◽  
Concrete Mix Design ◽  
Banana Tree ◽  
Flexible Fiber ◽  
Test Objects

<p align="center"><strong>Abstrak</strong></p><p> </p><p class="11daftarpustaka">Serat abaka merupakan serat yang awet dan lentur yang diambil dari pohon pisang. Serat ini masih sangat jarang dimanfaatkan, sementara di Indonesia serat abaka bisa ditemukan di mana mana. Tujuan penelitian ini adalah untuk mengetahui sejauh mana pengaruh serat abaka terhadap kuat lentur beton. Penelitian ini diawali dengan studi literature, pengujian material (Agregat halus, agregat kasar, semen dan serat abaka), mix design beton, pembuatan benda uji, perawatan dan dilanjutkan dengan pengujian kuat lentur beton serta terakhir dilakukan analisis hasil pengujian. Dari hasil pengujian didapatkan kuat lentur maksmum terjadi pada kadar serat abaka sebesar 0,6% dengan kuat lentur 3,75 MPa, sedangkan kuat lentur terkecil terjadi pada kadar serat abaka 0% dengan kuat lentur 3,34 MPa.</p><p class="11daftarpustaka"> </p><p class="11daftarpustaka">Kata kunci: <em>serat abaka,</em><em> kuat lentur, mix deisgn</em><em></em></p><p align="center"><strong> </strong></p><p align="center"><strong> </strong></p><p align="center"><strong>Abstract</strong></p><p class="11daftarpustaka"> </p><p class="11daftarpustaka">Abaca fiber is a durable and flexible fiber taken from the banana tree. This fiber is still very rarely used, while in Indonesian abaca fiber can be found everywhere. The purpose of this study was to determine the extent of the influence of abaca fiber on the flexural strength of concrete. This research begins with literature studies, material testing (fine aggregate, coarse aggregate, cement, and abaca fiber), concrete mix design, manufacture of test objects, curing, and continues with concretes flexural strength testing and finally an analysis of the test results. From the test results, it founded that the maximum flexural strength occurred at the abaca fiber content of 0.6% with a bending strength of 3.75 MPa, and the smallest flexural strength occurred at 0% abaca fiber content with a flexural strength of 3.34 MPa.</p><p class="11daftarpustaka"> </p><p class="11daftarpustaka">Keywords: <em>Abaka fiber,</em><em> flexural strength, mix design</em><em></em></p>

Properties of Unfired Building Bricks Prepared from Fly Ash and Residual Rice Husk Ash

2015 ◽  
Vol 754-755 ◽  
pp. 468-472 ◽  
Author(s):  
Chao Lung Hwang ◽  
Trong Phuoc Huynh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Fine Aggregate ◽  
Test Results ◽  
Design Algorithm ◽  
Potential Applications ◽  
Hardened Properties

This work investigates the possibility of using fly ash (FA) and Vietnam residual rice husk ash (RHA) in producing unfired building bricks with applying densified mixture design algorithm (DMDA) method. In this research, little amount of cement was added into the mixtures as binder substitution. Unground rice husk ash (URHA), an agricultural by-product, was used as partial fine aggregate replacement (10% and 30%) in the mixtures. The solid bricks of 220×105×60 mm in size were prepared in this study. The hardened properties of the bricks were investigated including compressive strength, flexural strength and water absorption according to corresponding Vietnamese standards. Forming pressure of 35 MPa was applied to form the solid bricks in the mold. The test results show that all brick specimens obtained good mechanical properties, which were well conformed to Vietnamese standard. Compressive strength and flexural strength of the bricks were respectively in range of 13.81–22.06 MPa and 2.25–3.47 MPa. It was definitely proved many potential applications of FA and RHA in the production of unfired building bricks.

scholarly journals THE EFFECT OF ADDING CEMENT WASTE ON THE QUALITY OF CONCRETE COMPRESSIVE

Jurnal CIVILA ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 213
Author(s):  
Asrul Majid ◽  
Hammam Rofiqi Agustapraja
Keyword(s):  
Compressive Strength ◽  
Strength Test ◽  
Fine Aggregate ◽  
Infrastructure Development ◽  
Test Results ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Concrete Materials ◽  
Test Objects

Infrastructure development is one of the important aspects of the progress of a country where most of the constituents of infrastructure are concrete. The most important constituent of concrete is cement because its function is to bind other concrete materials so that it can form a hard mass. The large number of developments using cement as a building material will leave quite a lot of cement bags.In this study, the authors conducted research on the effect of adding cement waste to the compressive strength of concrete. This study used an experimental method with a total of 24 test objects. The test object is in the form of a concrete cylinder with a diameter of 15 cm and a height of 30 cm and uses variations in the composition of the addition of cement waste cement as a substitute for fine aggregate, namely 0%, 2%, 4% and 6%. K200). The compressive strength test was carried out at the age of 7 days and 28 days.The test results show that the use of waste as a partial substitute for fine aggregate results in a decrease in the compressive strength of each mixture. at the age of 7 days the variation of 2% is 16.84 MPa, 4% is 11.32 MPa and for a mixture of 6% is 6.68 MPa. Meanwhile, the compressive strength test value of 28 days old concrete in each mixture decreased by ± 6 MPa. So the conclusion is cement cement waste cannot be used as a substitute for fine aggregate in fc 16.6 (K200) quality concrete because the value is lower than the specified minimum of 16.6 MPa.

scholarly journals Recycling of waste incineration bottom ash in the production of interlocking concrete bricks

2021 ◽  
Vol 15 (2) ◽  
pp. 101-112
Author(s):  
Nguyen Huu May ◽  
Huynh Trong Phuoc ◽  
Le Thanh Phieu ◽  
Ngo Van Anh ◽  
Chau Minh Khai ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Bending Strength ◽  
Bottom Ash ◽  
Waste Incineration ◽  
Engineering Properties ◽  
Fine Aggregate ◽  
Test Results ◽  
Toxic Material ◽  
Visible Defect

This study presents an experimental investigation on the recycling of waste incineration bottom ash (IBA) as a fine aggregate in the production of interlocking concrete bricks (ICB). Before being used, the concentration of heavy metal in IBA was determined to confirm it is a non-toxic material. In this study, the IBA was used to replace crushed sand (CSA) in the brick mixtures at different replacement levels of 0%, 25%, 50%, 75%, and 100% (by volume). The ICB samples were checked for dimensions, visible defects, compressive strength, bending strength, water absorption, and surface abrasion in accordance with the related Vietnamese standards. The test results demonstrated that the IBA used in this study was a non-toxic material, which can be widely used for construction activities. All of the ICB samples prepared for this study exhibited a nice shape with consistent dimensions and without any visible defects. The incorporation of IBA in the brick mixtures affected engineering properties of the ICB samples such as a reduction in the compressive strength and bending strength and an increment in water absorption and surface abrasion of the brick samples. As a result, the compressive strength, bending strength, water absorption, and surface abrasion values of ICB samples at 28 days were in the ranges of 20.6 – 34.9 MPa, 3.95 – 6.62 MPa, 3.8 – 7.2%, and 0.132 – 0.187 g/cm2, respectively. Therefore, either partial or full replacement of CSA by IBA, the ICB with grades of M200 – M300 could be produced with satisfying the TCVN 6476:1999 standard in terms of dimensions, visible defects, compressive strength, water absorption, and surface abrasion. These results demonstrated the high applicability of the local IBA in the production of the ICB for various construction application purposes. Keywords: interlocking concrete brick; waste incineration bottom ash; visible defect; compressive strength; bending strength; water absorption; surface abrasion.

scholarly journals PENGARUH SUBTITUSI LUMPUR SIDOARJO (LUSI) TERHADAP KUAT TEKAN BATA BETON (PAVING BLOCK)

2020 ◽  
Vol 12 (2) ◽  
pp. 89
Author(s):  
Masbuhin Masbuhin
Keyword(s):  
Compressive Strength ◽  
Experimental Method ◽  
Research Method ◽  
Strength Test ◽  
Mix Design ◽  
Fine Aggregate ◽  
Compressive Strength Test ◽  
Preparation Stage ◽  
Test Objects

This study aims to determine the process of utilizing Sidoarjo Mud (LUSI) as a substitute for paving blocks and to determine the results of the compressive strength test of using LUSI as a substitute for paving blocks. The LUSI substitution is expected to be able to provide innovations in the construction of a paving block mixture. The research method used is the experimental method. The manufacture of test objects starts from the preparation stage, mix design, manufacture of test objects, testing and classifying paving blocks according to SNI 03-0691-1996. The sample of specimens used normal mix design and mix design substitute LUSI 40% of the fine aggregate value. Based on the results of research, paving blocks with a normal mix design of 1Pc: 2Ps are classified as quality A, 1Pc: 3Ps and 1Pc: 4Ps are classified as B quality, while for paving blocks substituting LUSI in a mixture of 1Pc: 2Ps is classified as quality B, for a mixture of 1Pc: 3Ps and 1Pc : 4Ps is classified as C quality. It can be concluded that the compressive strength of paving blocks has decreased in compressive strength after being substituted by LUSI, with a successive percentage value of 32%, 59% and 58%.

scholarly journals Investigation on the Mechanical Properties of Fiber Reinforced Recycled Concrete

2016 ◽  
Vol 2 (1) ◽  
pp. 13-22 ◽  
Author(s):  
Hasan Jalilifar ◽  
Fatholla Sajedi ◽  
Sadegh Kazemi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Experimental Test ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Fiber Content ◽  
Recycled Concrete ◽  
Test Results ◽  
Fiber Volume ◽  
Flexural Toughness

The flexural strength of conventional concrete material is known to be enhanced by incorporating a moderate volume-fraction of randomly distributed fibers. However, there is limited information on describing the influence of fiber volume-fraction on the compressive and flexural strength of recycled coarse aggregate concrete (RCA-C) material. This paper reports on experimental test results of the RCA-C material replaced with 0, 30, 50 and 100% recycled aggregate and 0, 0.5, 1 and 1.5% steel fiber volume fraction. Three-point flexural tests of notched prism specimens were completed. The mechanical properties in compression were characterized using cube specimens. Significant improvement in compressive and flexural strength of RCA-C was found as fiber content increased from 0 to 1.5%. The experimental test results of RCA-C were further evaluated to investigate the influence of fiber content on flexural toughness. According to test results, the addition of steel fibers to RCA-C material appreciably increased the flexural toughness.

scholarly journals Concrete Mix Design for Completely Recycled Fine Aggregate by Modified Packing Density Method

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3535
Author(s):  
Yibo Yang ◽  
Baixi Chen ◽  
Yan Su ◽  
Qianpu Chen ◽  
Zhiji Li ◽  
...  
Keyword(s):  
Packing Density ◽  
Unit Price ◽  
Mix Design ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Density Method ◽  
Concrete Mix Design ◽  
Recycled Fine Aggregate ◽  
Concrete Mix ◽  
Aggregate System

The undesirable properties of conventional recycled fine aggregate (RFA) often limit its application in the construction industry. To overcome this challenge, a method for preparing completely recycled fine aggregate (CRFA), which crushes all concrete waste only into fine aggregate, was proposed. The obtained CRFA had high apparent density, and its water absorption was lower than that of the conventional RFA. To take advantage of the CRFA, this paper introduced the modified packing density method for the CRFA concrete mix design. The modified packing density method took account of the powder with a particle size of smaller than 75 μm in the CRFA and balanced both the void ratio and the specific surface area of the aggregate system. Concrete (grade C55) was prepared using the CRFA to validate the feasibility of the proposed method. The unit price of the prepared CRFA concrete was around 12.7% lower than that of the natural aggregate concrete. Additionally, the proposed procedure for the concrete mixture design could recycle all concrete waste into the new concrete and replace all the natural fine aggregate in the concrete mixture.

Determination of Mechanical Properties of Biodegradable Composites Made by Pine Resin Corn Fibers and Henequen Fibers

2012 ◽  
Vol 517 ◽  
pp. 422-429 ◽  
Author(s):  
Esmeralda Uribe Lam ◽  
María Gabriela Gutiérrez Pliego ◽  
Víctor Gerardo Martínez Pérez ◽  
Alejandro Manzano Ramirez
Keyword(s):  
Flexural Strength ◽  
Bending Strength ◽  
Resin Composite ◽  
Fiber Content ◽  
Corn Fiber ◽  
Recycled Paper ◽  
Pine Resin ◽  
Biodegradable Composites ◽  
Negative Effect ◽  
Corn Fibers

Flexion tests were performed (ASTM D790) for two biodegradable composites, the first one made of pine resin as matrix and henequen fibers as reinforcement, varying the percentage reinforcement. The second composite made of a matrix of cellulose obtained from a mixture of recycled paper and water and reinforced with maize bract fibers (the leaves that cover the corn cob) and infiltrated with pine resin. Five samples were evaluated for each compound in an Instron universal machine (load cell: 5 kN). For the henequen fibers and pine resin composite specimens were prepared according to standard by the method of hot casting resin, henequen fibers both short and long (127mm, 10mm) were included prior to discharge the matrix. The drying was at room temperature for 1 minute. Tests were conducted with different compositions of matrix / reinforcement by varying the amount of fiber in 26%, 20% and 14% of the specimen. The long fibers longitudinally traverse the specimen (127mm) and short fibers (10 mm) are dispersed in the mixture. The second composite is produced from corn fiber preforms and cellulose by the method of compression molding, dried in oven at 100 ° C for 2 hours. The preforms were infiltrated with pine resin by compressed air (25 psi). We analyzed the effect of corn fiber content in weight percentages of 10%, 30% and 50% with respect to cellulose and two lengths of corn fiber (22.25μm and 487 μm). Under study conditions, corn fiber generates a negative effect on the flexural strength of the compound. By increasing the fiber content of corn and its size, the bending strength decreased in almost all cases, is attributed to a lack of uniformity in the distribution of corn fibers. However, flexural strength values obtained were similar to materials such as wood, found in the literature. This projects the potential of the compound to replace, in certain applications, non-sustainable material

scholarly journals LIGHTWEIGHT CONCRETE MAKING ANALYSIS USING MIXED CELLULOSE

2019 ◽  
Vol 2 (2) ◽  
pp. 85-91
Author(s):  
Nanang Budi Setyawan ◽  
Fredy Kurniawan
Keyword(s):  
Compressive Strength ◽  
Experimental Method ◽  
Lightweight Concrete ◽  
Mix Design ◽  
Waste Paper ◽  
Test Results ◽  
Concrete Mix Design ◽  
Concrete Mix ◽  
Recycle Paper ◽  
Compressive Strength Of Concrete

Development era of globalization has resulted in increasing number of second-hand goods / waste that its existence can be a problem for life in the future. Many things are done in order to recycle paper cement in order to overcome this problem the existence of waste. One way is to use waste paper to be a part of the building. The purpose of this study, to determine the compressive strength and optimum density. Laboratory experimental method uses a variation of 10%, 20%, 30% and testing conducted in the form of compressive strength and density. From the test results obtained by the result of decrease in the compressive strength and density. In addition cellulose concrete mix design with variations determined that 10%, 20%, 30% resulted in a decrease in the compressive strength of concrete,

Development of Concrete Mix Design Nomograph Containing Polyethylene Terephtalate (PET) as Fine Aggregate

2013 ◽  
Vol 701 ◽  
pp. 12-16 ◽  
Author(s):  
Mohd Irwan Juki ◽  
Khairunnisa Muhamad ◽  
Mahamad Mohd Khairil Annas ◽  
Koh Heng Boon ◽  
Norzila Othman ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Splitting Tensile Strength ◽  
Mix Design ◽  
Fine Aggregate ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Concrete Mix Design ◽  
Mix Proportion ◽  
Concrete Mix

This paper describes the experimental investigation to develop the concrete mix design Nomograph for concrete containing PET as fine aggregate. The physical and mechanical properties were determined by using mix proportion containing 25%, 50% and 75% of PET with water cement ratio (w/c) 0.45, 0.55 and 0.65. The data obtained showed that the inclusion of PET aggregate reduce the strength performances of concrete. All the data obtained were combined into one single graph to develop a preliminary mix design nomograph for PET concrete. The nomograph consist of ; relationship between compressive strength and water cement ratio; relationship between splitting tensile strength water cement ratio; relationship between splitting tensile strength and PET percentage and relationship between compressive strength and PET percentage. The mix design nomograph can be used to assists in selecting the proper mix proportion parameters based on the criteria required.

USING CERAMIC WASTES IN CONCRETE MANUFACTURING FOR SUSTAINABLE CONSTRUCTION MATERIALS AS COARSE AGGREGATE REPLACEMENT

2020 ◽  
Vol 7 (2) ◽  
Author(s):  
Mohamed Tarek El-Hawary ◽  
Amr Maher Elnemr ◽  
Nagy Fouad Hanna
Keyword(s):  
Coarse Aggregate ◽  
Construction Materials ◽  
Mix Design ◽  
Sustainable Construction ◽  
Fine Aggregate ◽  
Conventional Concrete ◽  
Ceramic Waste ◽  
Concrete Mix Design ◽  
Concrete Mixtures ◽  
Waste Concrete

About 30% of the ceramic production all over the world considered as waste. This huge amount of ceramic waste can be recycled in the construction industry, especially in concrete mix design, which is the main scope of this research. Ceramic wastes could provide many advantages rather than sustainability. It is considered economical and can replace cement, coarse aggregate, and fine aggregate, such as sand. In this study, several concrete mixtures were designed according to the ACI standards to assess the ceramic waste concrete for fresh and hardened properties in terms of slump, concrete compressive, splitting tensile and flexural strengths. Six mixes included with 0%, 10%, 20%, 30%, 40% and 50% replacement of coarse aggregate by crushed ceramic waste. By comparing the results between ceramic waste concrete and conventional concrete specimens, the optimum mix design was found to be at 30%-coarse aggregate replacement. Scanning electron microscope tests performed on the concrete specimens to examine the bond between the particles, the porosity, and the elementary composition of the specimens. The percentage of savings in cost estimated when using the optimum mix design (30% coarse aggregate replacement) was about a 30% reduction in the construction cost per the Egyptian market.

Sign in / Sign up

Export Citation Format

Share Document