Mango (Magnifera indica) seed oil grown in Dilla town as potential raw material for biodiesel production using NaOH- a homogeneous catalyst

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Diesel Engine ◽  
Physicochemical Properties ◽  
Seed Oil ◽  
Methyl Esters ◽  
Pollution Prevention ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Minimal Amount

Biodiesel produced by transesterification process from vegetable oils or animal fats is viewed as a promising renewable energy source. Now a day’s diminishing of petroleum reserves in the ground and increasing environmental pollution prevention and regulations have made searching for renewable oxygenated energy sources from biomasses. Biodiesel is non-toxic, renewable, biodegradable, environmentally benign, energy efficient and diesel substituent fuel used in diesel engine which contributes minimal amount of global warming gases such as CO, CO2, SO2, NOX, unburned hydrocarbons, and particulate matters. The chemical composition of the biodiesel was examined by help of GC-MS and five fatty acid methyl esters such as methyl palmitate, methyl stearate, methyl oleate, methyl linoleate and methyl linoleneate were identified. The variables that affect the amount of biodiesel such as methanol/oil molar ratio, mass weight of catalyst and temperature were studied. In addition to this the physicochemical properties of the biodiesel such as (density, kinematic viscosity, iodine value high heating value, flash point, acidic value, saponification value, carbon residue, peroxide value and ester content) were determined and its corresponding values were 87 Kg/m3, 5.63 Mm2/s, 39.56 g I/100g oil, 42.22 MJ/Kg, 132oC, 0.12 mgKOH/g, 209.72 mgKOH/g, 0.04%wt, 12.63 meq/kg, and 92.67 wt% respectively. The results of the present study showed that all physicochemical properties lie within the ASTM and EN biodiesel standards. Therefore, mango seed oil methyl ester could be used as an alternative to diesel engine.

Biodiesel Production From Crude Rubber Seed Oil Using Supercritical Methanol Transesterification

2015 ◽  
Vol 781 ◽  
pp. 655-658 ◽  
Author(s):  
Thakun Sawiwat ◽  
Somjai Kajorncheappunngam
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Supercritical Methanol ◽  
Rubber Seed Oil ◽  
Promising Alternative ◽  
Rubber Seed ◽  
Biodiesel Synthesis

Synthesis of biodiesel from rubber seed oil using a supercritical methanol was investigated under various reaction conditions (220 - 300°C, 80 - 180 bar) with reaction time of 1-15 min and oil:methanol molar ratio of 1:20 - 1:60. Free fatty acid methyl esters (FAMEs) content were analyzed by gas chromatography-mass spectroscopy (GC-MS). Most properties of produced biodiesel were in good agreement with biodiesel standard (EN 14214). The maximum FAME yield of 86.90% was obtained at 260°C, 160 bar, 5 min reaction time using oil:methanol molar ratio of 1:40. The result showed the acid value of rubber seed oil decreased to 0.58 mgKOH/g from initial 24 mgKOH/g to. It could be concluded from this findings that crude rubber seed oil is a promising alternative raw material for biodiesel synthesis via supercritical methanol tranesterification.

Impact of Using Biodiesels of Different Origin and Additives on the Performance of a Stationary Diesel Engine

2000 ◽  
Vol 122 (4) ◽  
pp. 624-631 ◽  
Author(s):  
A. Serdari ◽  
K. Fragioudakis ◽  
S. Kalligeros ◽  
S. Stournas ◽  
E. Lois
Keyword(s):  
Diesel Engine ◽  
Fatty Acid Methyl Esters ◽  
Corn Oil ◽  
Methyl Esters ◽  
Raw Material ◽  
Biodiesel Production ◽  
Exhaust Emission ◽  
Fuel Blends ◽  
Different Types ◽  
Particulate Matter Emissions

With the exception of rape seed oil which is the principal raw material for biodiesel Fatty Acid Methyl Esters, (FAME) production, sunflower oil, corn oil, and olive oil, which are abundant in Southern Europe, along with some wastes, such as used frying oils, appear to be attractive candidates for biodiesel production. In this paper fuel consumption and exhaust emission measurements from a single cylinder, stationary diesel engine are described. The engine was fueled with fuel blends containing four different types of biodiesel, at proportions up to 100 percent; the further impact of the usage of two specific additives was also investigated. The four types of biodiesel appeared to have equal performance and irrespective of the raw material used for their production, their addition to the traditional diesel fuel improved the particulate matter emissions. The results improve further when specific additive combinations are used. [S0742-4795(00)00604-9]

scholarly journals THE EFFECT OF MIXING ON THE PRODUCTION OF BIODIESEL FROM NEEM SEED OIL USING METHANOL AND HOMOGENEOUS CATALYST

2018 ◽  
Vol 6 (9) ◽  
pp. 451-457
Author(s):  
F. Sini ◽  
I. M Atadashi
Keyword(s):  
Seed Oil ◽  
Methyl Esters ◽  
Research Work ◽  
Molar Ratio ◽  
Biodiesel Fuel ◽  
Homogeneous Catalyst ◽  
Neem Seed ◽  
Neem Oil ◽  
Neem Seed Oil ◽  
American Society

Biodiesel was prepared through alkali-catalysed transesterification of neem seed oil using sodium hydroxide as catalyst and ethanol. This process of was carried out firstly throuch eserification and then via transesterification. The process was carried out by varying stirring speed (350, 450, 550, 650, 750 and 850 rpm.) and keeping other variables constant (temperature of 60oC, catalyst concentration of 1w/w%  and 6:1 oil to ethanol molar ratio). In this research work, a yield of 93w/w% was achieved at the stirring speed of 850 rpm. It was observed that the viscosity (3.73mm2/s at 400C) of neem oil methylester generated was within the limit (2-6mm2/s) specified by the American Society for Testing and Materials Standards. The density of neem biodiesel at ambient temperature (250C) was found to be 0.85g/ml, which is exactly close to the density of diesel (0.83g/ml). The Flash Point of the neem oil biodiesel produced was 153.60C which above the ASTM D6751 minimum standards for biodiesel fuel of 130oC. Furthermore, Neem oil biodiesel has a pour point of -40C and a cloud point of 20C. These values clearly indicate that the use of neem oil methyl esters in colder regions is limited. However, this value is also indicative of the high potential of this fuel as biodiesel particularly in Northern Nigeria where temperature is always above 20oC, a temperature at which the oil is fluid.

scholarly journals Production and Characterization of Biodiesel Derived from a Novel Source Koelreuteria paniculata Seed Oil

Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 791 ◽  
Author(s):  
Inam Ullah Khan ◽  
Zhenhua Yan ◽  
Jun Chen
Keyword(s):  
Fatty Acid ◽  
Seed Oil ◽  
Methyl Esters ◽  
Chemical Properties ◽  
Raw Material ◽  
Biodiesel Production ◽  
Edible Plant ◽  
Physico Chemical ◽  
Koelreuteria Paniculata ◽  
The Cost

Biodiesel is a clean and renewable fuel, which is considered as the best alternative to diesel fuel, but the feedstock contributes more than 70% of the cost. The most important constituent essential for biodiesel development is to explore cheap feedstock with high oil content. In this work, we found novel non-edible plant seeds of Koelreuteria paniculata (KP) with high oil contents of 28–30 wt.% and low free fatty acid contents (0.91%), which can serve as a promising feedstock for biodiesel production. KP seed oil can convert into biodiesel/fatty acid methyl esters (FAMEs) by base-catalyzed transesterification with the highest biodiesel production of 95.2% after an optimization process. We obtained the optimal transesterification conditions, i.e., oil/methanol ratio (6:1), catalyst concentration (0.32), reaction temperature (65 °C), stirring rate (700 rpm), and reaction time (80 min). The physico-chemical properties and composition of the FAME were investigated and compared with mineral diesel. The synthesized esters were confirmed and characterized by the application of NMR (1H and 13C), FTIR, and GC-MS. The biofuel produced from KP seed oil satisfies the conditions verbalized by ASTM D6751 and EN14214 standards. Accordingly, KP source oil can be presented as a novel raw material for biofuel fabrication.

scholarly journals Comparative analyses of biodiesel produced from neem and jatropha seed oil

2021 ◽  
Vol 12 (2) ◽  
pp. 141-143
Author(s):  
I.S. Ibrahim ◽  
I.T. Abdullahi ◽  
F.Y. Muhammad
Keyword(s):  
Reaction Time ◽  
Methyl Ester ◽  
Physicochemical Properties ◽  
Seed Oil ◽  
Methyl Esters ◽  
Reaction Times ◽  
Biodiesel Production ◽  
Jatropha Oil ◽  
Jatropha Seed ◽  
Astm D6751

Biodiesel is derived from triglycerides by transesterification reaction with alcohol (ethanol or methanol), and has classified as a renewable, biodegradable, and nontoxic fuel. Several methods for biodiesel production have been developed, among which transesterification using alkali-catalysis gives high levels of conversion of triglycerides to their corresponding methyl esters in short reaction times. This study was conducted to extract the neem and Jatropha oil for the production of biodiesel using alkali-catalyzed reaction The samples were subjected to reaction with sodium hydroxide (NaOH), 0.2:1 w/v methanol (MeOH) to oil mole ratio, reaction temperature of 6°C, and 30 min reaction time. The final biodiesel yield obtained was 47.5% and 45.5% from the neem and the jaropha oil sample respectively. The basic physicochemical properties of the jatropha methyl ester produced from both jatropha oil samples were found to be within the ASTM D6751 specified limits.

scholarly journals Optimization of the real conversion efficiency of waste cooking oil to fame

2021 ◽  
pp. 200-200
Author(s):  
James Vera-Rozo ◽  
Jose Riesco-Avila ◽  
Francisco Elizalde-Blanca ◽  
Sergio Cano-Andrade
Keyword(s):  
Prediction Models ◽  
Polynomial Regression ◽  
Methyl Esters ◽  
Waste Cooking Oil ◽  
Raw Material ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Conversion Yield ◽  
Waste Vegetable Oil ◽  
Chemical Conditions

This work presents a polynomial regression model for the optimization of the content of fatty acid methyl esters (FAME) and the conversion yield of waste vegetable oil to biodiesel. The equations are optimized to obtain the maximum FAME yield, which is the product of the conversion yield and the FAME content in the biodiesel. The independent variables considered are the type of catalyst used (KOH and NaOH), percentage of catalyst (0.6%, 1.0% and 1.5% w/w with respect to oil), and the methanol: oil molar ratio (6:1, 7.5:1 and 9:1). The prediction models are obtained by using nine experimental points for each catalyst. The validation is developed with four main experimental points from the mapping. A polynomial relation is obtained as a consequence, which correlates each of the experimental variables with the FAME and conversion yield. The optimization of the proposed models shows an error of 2.66% for the FAME, and an error of less than 1% for the conversion yield are obtained. This work presents a straightforward methodology to obtain the best chemical conditions in the production of biodiesel by using a small number of experiments, obtaining good results. This methodology can be applied for biodiesel production from any raw material, recalculating each of the regression constants thus allowing to obtain the highest quantity of oil to be converted in FAME.

scholarly journals Synthesis and Characterization of Biodiesel from Khaya senegalensis Seed Oil using Heterogeneous Catalyst

2019 ◽  
pp. 101-107
Author(s):  
Mohammed Babakura ◽  
Jibrin M. Yelwa ◽  
Abubakar Ibrahim ◽  
Bashir M. Aliyu ◽  
Jibrin Y. Yahaya ◽  
...  
Keyword(s):  
Fatty Acid ◽  
Heterogeneous Catalyst ◽  
Fatty Acid Methyl Esters ◽  
Seed Oil ◽  
Methyl Esters ◽  
Acid Value ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Acid Methyl ◽  
Khaya Senegalensis

Biodiesel was produced by transesterifying Khaya senegalensis oil with methanol in the presence of Al2O3 as catalyst. Molar ratio of 15:1 (methanol to oil) was followed to shift the reaction to product side for more yield of fatty acid methyl esters (FAME) and the use of a heterogeneous catalyst enabled the reaction to proceed faster. The oil and biodiesel were characterized following ASTM standards. The free fatty acid, acid value, viscosity, specific gravity, moisture content, saponification value, pour point, cloud point were examined in this research and the result obtained show that Khaya senegalensis Seed Oil is a good for biodiesel production. The biodiesel obtained was separated from glycerol, washed with distilled water and dried. Samples of oil and biodiesel were scan within mid-infrared region of 4000 cm-1 – 400 cm-1 with fourier transform infrared spectrometer by agilent technologies. The spectra obtained were interpreted and analyzed with the aid of structure correlation chart. The results revealed that the biodiesel contained fatty acid methyl esters (FAME). The FTIR spectrum for the biodiesel revealed the functional groups with characteristics bands, C=O, -(CH2)n-, C-O, C=C and C-H in the spectrum.

scholarly journals THE EFFECTS OF VARIATION OF CATALYST CONCENTRATION ON BIODIESEL PRODUCTION

2018 ◽  
Vol 6 (9) ◽  
pp. 487-496
Author(s):  
Janet John Nahadi ◽  
Musa Idris Atadashi
Keyword(s):  
Catalyst Concentration ◽  
Methyl Esters ◽  
Coconut Oil ◽  
Flash Point ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Homogeneous Catalyst ◽  
Animal Fats ◽  
High Conversion Rate ◽  
Ft Ir

Biodiesel is defined as mono-alkyl esters of long chain fatty acids derived from vegetable oils or animal fats, which conform to ASTM D6751 specifications for use in diesel engines. Fuel-grade biodiesel must be produced to strict industry specifications in order to ensure proper performance. Biodiesel contains no petroleum, but it can be blended at any level with petroleum diesel to create a biodiesel blend. From the production and characterization of biodiesel via the alkaline transesterification of coconut oil using different concentrations homogeneous catalyst (sodium hydroxide), oil to methanol molar ratio of 1:6, reaction temperature of 550C and reaction time of 60 min. Biodiesel can serve as a potential feedstock for the production of biodiesel owing to its high conversion rate and relatively low FFA content. At a catalyst concentration of 1%w/w oil NaOH catalyst, optimum yield of up to 96% was achieved. It is interesting to note that the viscosity of the biodiesel obtained falls within the limit as specified by ASTM D445 (2003). A flash point of 154.2 was obtained for the coconut biodiesel. This shows that the biodiesel is safe for handling as the flash point exceeds the minimum stipulated by the ASTM (93min). The transformation of the triglycerides present in most oils into methyl ester was confirmed by FT-IR studied. Further investigation regarding the profile of the acid methyl esters present in the oil was confirmed using GC-MS analysis.

Efficient Micromixing for Continuous Biodiesel Production from Jatropha Oil

2018 ◽  
Vol 9 (1) ◽  
pp. 133-139
Author(s):  
Waleed S. Mohammed ◽  
Ahmed H. El-Shazly ◽  
Marwa F. Elkady ◽  
Masahiro Ohshima
Keyword(s):  
Methyl Esters ◽  
Continuous Process ◽  
Sol Gel ◽  
Average Diameter ◽  
Biodiesel Production ◽  
High Mass ◽  
Molar Ratio ◽  
Jatropha Oil ◽  
Energy Deficiency ◽  
Gel Preparation

Introduction: The utilization of biodiesel as an alternative fuel is turning out to be progressively famous these days because of worldwide energy deficiency. The enthusiasm for utilizing Jatropha as a non-edible oil feedstock is quickly developing. The performance of the base catalyzed methanolysis reaction could be improved by a continuous process through a microreactor in view of the high mass transfer coefficient of this technique. Materials & Methods: Nanozirconium tungstovanadate, which was synthetized using sol-gel preparation method, was utilized in a complementary step for biodiesel production process. The prepared material has an average diameter of 0.066 &µm. Results: First, the NaOH catalyzed methanolysis of Jatropha oil was investigated in a continuous microreactor, and the efficient mixing over different mixers and its impact on the biodiesel yield were studied under varied conditions. Second, the effect of adding the nanocatalyst as a second stage was investigated. Conclusion: The maximum percentage of produced methyl esters from Jatropha oil was 98.1% using a methanol/Jatropha oil molar ratio of 11 within 94 s using 1% NaOH at 60 &°C. The same maximum conversion ratio was recorded with the nanocatalyst via only 0.3% NaOH.

scholarly journals Biodiesel Production from a Novel Nonedible Feedstock, Soursop (Annona muricata L.) Seed Oil

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2562 ◽  
Author(s):  
Chia-Hung Su ◽  
Hoang Nguyen ◽  
Uyen Pham ◽  
My Nguyen ◽  
Horng-Yi Juan
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Annona Muricata ◽  
Reaction Conditions ◽  
Biodiesel Feedstock ◽  
Acid Catalyzed ◽  
American Society ◽  
Optimal Reaction

This study investigated the optimal reaction conditions for biodiesel production from soursop (Annona muricata) seeds. A high oil yield of 29.6% (w/w) could be obtained from soursop seeds. Oil extracted from soursop seeds was then converted into biodiesel through two-step transesterification process. A highest biodiesel yield of 97.02% was achieved under optimal acid-catalyzed esterification conditions (temperature: 65 °C, 1% H2SO4, reaction time: 90 min, and a methanol:oil molar ratio: 10:1) and optimal alkali-catalyzed transesterification conditions (temperature: 65 °C, reaction time: 30 min, 0.6% NaOH, and a methanol:oil molar ratio: 8:1). The properties of soursop biodiesel were determined and most were found to meet the European standard EN 14214 and American Society for Testing and Materials standard D6751. This study suggests that soursop seed oil is a promising biodiesel feedstock and that soursop biodiesel is a viable alternative to petrodiesel.

Sign in / Sign up

Export Citation Format

Share Document