Real Time SEM Imaging of FIB Milling Processes for Extended Accuracy on TEM Samples for EFTEM Analysis

2003 ◽  
Author(s):  
P. Gnauck ◽  
U. Zeile ◽  
P. Hoffrogge ◽  
G. Benner ◽  
A. Orchowski ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Process Development ◽  
Ion Beam ◽  
Quantitative Information ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Ic Manufacturing ◽  
On Line ◽  
Broad Variety ◽  
Preparation Techniques

Abstract We present application examples of site specific energy filtered transmission electron microscopy (EFTEM) analysis using advanced focused ion beam (FIB) specimen preparation techniques. Specifically, we address topics such as throughput and reliability enhancement by chemically assisted broad ion beam milling and on-line monitoring of the etch process. We discuss how integrated elemental analysis by EFTEM can be used to gain quantitative information on the broad variety of new material systems currently entering front end and back end of the IC manufacturing process line. The accelerating pace of device integration results in extreme demands for quantitative analysis in process development, yield ramp-up and process control with spatial resolution and elemental sensitivity at the very limits of currently available instrumentation. Historically, the high resolution performance of TEM analysis has been hampered by long turn around times for the required sample preparation. Meanwhile the routine use of FIB systems for “trench” and “lift-out” preparation techniques allows for an enormous increase in the efficiency of TEM analysis.

Comparison of Precision XTEM Specimen Preparation Techniques for Semiconductor Failure Analysis

1997 ◽  
Vol 3 (S2) ◽  
pp. 357-358
Author(s):  
C. Amy Hunt
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Mechanical Polishing ◽  
Specimen Preparation ◽  
Ion Milling ◽  
Tem Analysis ◽  
The Past ◽  
Preparation Techniques

The demand for TEM analysis in semiconductor failure analysis is rising sharply due to the shrinking size of devices. A well-prepared sample is a necessity for getting meaningful results. In the past decades, a significant amount of effort has been invested in improving sample preparation techniques for TEM specimens, especially precision cross-sectioning techniques. The most common methods of preparation are mechanical dimpling & ion milling, focused ion beam milling (FIBXTEM), and wedge mechanical polishing. Each precision XTEM technique has important advantages and limitations that must be considered for each sample.The concept for both dimpling & ion milling and wedge specimen preparation techniques is similar. Both techniques utilize mechanical polishing to remove the majority of the unwanted material, followed by ion milling to assist in final polishing or cleaning. Dimpling & ion milling produces the highest quality samples and is a relatively easy technique to master.

Microstructural Characterization of Automated Specimen Preparation for TEM Analysis

2000 ◽  
Vol 6 (S2) ◽  
pp. 528-529
Author(s):  
C. Urbanik Shannon ◽  
L. A. Giannuzzi ◽  
E. M. Raz
Keyword(s):  
Focused Ion Beam ◽  
Preparation Method ◽  
Ion Beam ◽  
Microstructural Characterization ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Area Of Interest ◽  
Transmission Electron ◽  
Preparation Techniques

Automated specimen preparation for transmission electron microscopy has the obvious advantage of saving personnel time. While some people may perform labor intensive specimen preparation techniques quickly, automated specimen preparation performed in a timely and reproducible fashion can significantly improve the throughput of specimens in an industrial laboratory. The advent of focused ion beam workstations for the preparation of electron transparent membranes has revolutionized TEM specimen preparation. The FIB lift-out technique is a powerful specimen preparation method. However, there are instances where the “traditional” FIB method of specimen preparation may be more suitable. The traditional FIB method requires that specimens must be prepared so that the area of interest is as thin as possible (preferably less than 50 μm) prior to FIB milling. Automating the initial specimen preparation for brittle materials (e.g., Si wafers) may be performed using the combination of cleaving and sawing techniques as described below.

A Methodology to Reduce Ion Beam Induced Damage in TEM Specimens Prepared by FIB

2002 ◽  
Author(s):  
Chin Kai Liu ◽  
Chi Jen. Chen ◽  
Jeh Yan.Chiou ◽  
David Su
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Sensitive Issue ◽  
Transmission Electron

Abstract Focused ion beam (FIB) has become a useful tool in the Integrated Circuit (IC) industry, It is playing an important role in Failure Analysis (FA), circuit repair and Transmission Electron Microscopy (TEM) specimen preparation. In particular, preparation of TEM samples using FIB has become popular within the last ten years [1]; the progress in this field is well documented. Given the usefulness of FIB, “Artifact” however is a very sensitive issue in TEM inspections. The ability to identify those artifacts in TEM analysis is an important as to understanding the significance of pictures In this paper, we will describe how to measure the damages introduced by FIB sample preparation and introduce a better way to prevent such kind of artifacts.

Characterization of FIB Damage in Silicon

1999 ◽  
Vol 5 (S2) ◽  
pp. 740-741 ◽  
Author(s):  
C.A. Urbanik ◽  
B.I. Prenitzer ◽  
L.A. Gianhuzzi ◽  
S.R. Brown ◽  
T.L. Shofner ◽  
...  
Keyword(s):  
Focused Ion Beam ◽  
Ion Beam ◽  
Target Material ◽  
Beam Current ◽  
Specimen Preparation ◽  
Transfer Energy ◽  
Transmission Electron ◽  
Preparation Techniques ◽  
Reactive Gas

Focused ion beam (FIB) instruments are useful for high spatial resolution milling, deposition, and imaging capabilities. As a result, FIB specimen preparation techniques have been widely accepted within the semiconductor community as a means to rapidly prepare high quality, site-specific specimens for transmission electron microscopy (TEM) [1]. In spite of the excellent results that have been observed for both high resolution (HREM) and standard TEM specimen preparation applications, a degree of structural modification is inherent to FIB milled surfaces [2,3]. The magnitude of the damage region that results from Ga+ ion bombardment is dependent on the operating parameters of the FIB (e.g., beam current, beam voltage, milling time, and the use of reactive gas assisted etching).Lattice defects occur as a consequence of FIB milling because the incident ions transfer energy to the atoms of the target material. Momentum transferred from the incident ions to the target atoms can result in the creation of point defects (e.g., vacancies, self interstitials, and interstitial and substitutional ion implantation), the generation of phonons, and plasmon excitation in the case of metal targets.

Focused Ion Beam Milling and Micromanipulation Lift-Out for Site Specific Cross-Section Tem Specimen Preparation

1997 ◽  
Vol 480 ◽  
Author(s):  
L. A. Giannuzzi ◽  
J. L. Drown ◽  
S. R. Brown ◽  
R. B. Irwin ◽  
F. A. Stevie
Keyword(s):  
Cross Section ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specific Area ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Site Specific ◽  
Area Of Interest ◽  
Carbon Coated ◽  
A Site

AbstractA site specific technique for cross-section transmission electron microscopy specimen preparation of difficult materials is presented. Focused ion beams are used to slice an electron transparent sliver of the specimen from a specific area of interest. Micromanipulation lift-out procedures are then used to transport the electron transparent specimen to a carbon coated copper grid for subsequent TEM analysis. The experimental procedures are described in detail and an example of the lift-out technique is presented.

TEM FIB Lift-Out of Mount Saint Helens Volcanic Ash

1999 ◽  
Vol 5 (S2) ◽  
pp. 908-909
Author(s):  
J.L. Drown-MacDonald ◽  
B.I. Prenitzer ◽  
T.L. Shofner ◽  
L.A. Giannuzzi
Keyword(s):  
Cross Sections ◽  
Volcanic Ash ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Preparation Technique ◽  
Tem Analysis ◽  
Plan View ◽  
Transmission Electron ◽  
Silver Paint

Focused Ion Beam (FIB) specimen preparation for both scanning and transmission electron microscopy (SEM and TEM respectively) has seen an increase in usage over the past few years. The advantage to the FIB is that site specific cross sections (or plan view sections) may be fabricated quickly and reproducibly from numerous types of materials using a finely focused beam of Ga+ ions [1,2]. It was demonstrated by Prenitzer et al. that TEM specimens may be acquired from individual Zn powder particles by employing the FIB LO specimen preparation technique [3]. In this paper, we use the FIB LO technique to prepare TEM specimens from Mount Saint Helens volcanic ash.Volcanic ash from Mount Saint Helens was obtained at the Microscopy and Microanalysis 1998 meeting in Atlanta. TEM analysis of the ash was performed using the FIB lift out technique [1]. Ash powders were dusted onto an SEM sample stud that had been coated with silver paint.

scholarly journals TEM Sample Preparation for the Semiconductor Industry - Part 2

1996 ◽  
Vol 4 (1) ◽  
pp. 8-9
Author(s):  
Dave Laken
Keyword(s):  
Sample Preparation ◽  
Focused Ion Beam ◽  
High Current Density ◽  
Ion Beam ◽  
Semiconductor Industry ◽  
Tem Analysis ◽  
Ion Beam Etching ◽  
Chemical Etch ◽  
Different Characteristics ◽  
Preparation Techniques

In the November issue of this publication, we described how focused ion beam (FIB) microsurgery is used to successfully cross-section and prepare material-specific samples for SEM and TEM analysis. Material specific samples have two or more components possessing different characteristics, such as hardness and chemical etch or sputtering rates. Traditional sample preparation techniques (mechanical grinding and polishing, broad ion beam etching, and chemical etching) alter, delaminate, or destroy these samples.FIB handles the preparation of these difficult samples well because of its milling geometry and the high current density of the small beam.

scholarly journals Using a Focused Ion Beam (FIB) System to Extract TEM-Ready Samples from Complex Metallic and Ceramic Structures

1999 ◽  
Vol 7 (2) ◽  
pp. 12-15 ◽  
Author(s):  
Lucille A. Giannuzzi ◽  
Richard Young ◽  
Pete Carleson
Keyword(s):  
Focused Ion Beam ◽  
Preparation Method ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Magnetic Media ◽  
Tem Analysis ◽  
Micro Fabrication ◽  
Site Specific ◽  
Transmission Electron ◽  
Two Sides

AbstractDriven by the analytical needs of microelectronics, magnetic media and micro-fabrication industries, focused ion beam (FIB) systems are now capable of milling and manipulating samples for the analysis of microstructure features having dimensions of 180 nm or less, A technique for locating and extracting site specific specimens for examination by transmission electron microscopy (TEM) has been developed. An identified feature can be located and precisely milled with an FIB system from two sides to prepare an ultrathin sample, and then extracted from the region with a glass rod micromanipulator onto a grid for TEM analysis. This specimen preparation method has been applied to semiconductor failure analysis and to the study of metallic and ceramic microsiructures with irregular topographies and complex mufti-layered components.

TEM sample preparation with focused ion beams

1991 ◽  
Vol 49 ◽  
pp. 1108-1109
Author(s):  
S. J. Kirch ◽  
Ron Anderson ◽  
Stanley J. Klepeis
Keyword(s):  
Sample Preparation ◽  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Surface Preparation ◽  
Tem Analysis ◽  
Cross Sectional ◽  
Transmission Electron ◽  
Special Surface ◽  
Preparation Techniques

The continuing reduction in the sizes of features of interest for integrated circuit failure analysis requires greater precision in transmission electron microscopy (TEM) sample preparation. With minimum feature sizes approaching 0.5 μm, the mere finding of such a feature at a polished edge, let alone preparing a TEM sample containing it becomes a formidable task. The required substantial thinning also increases the risk of loss of what may be a unique sample.We present in this paper a technique that allows localized thinning of cross-sectional TEM samples using a focused ion beam (FIB) machine. Standard preparation techniques are used to make a cross-sectional TEM sample that would otherwise be too thick to be very useful for TEM analysis. This sample is then placed in the FIB machine, which is used as a micromachining tool. No special surface preparation is necessary and the secondary electron signal generated by the ion beam provides an image that can be used to locate the feature of interest.

A Tutorial of the Fib Lift-Out Technique for TEM Specimen Preparation

1999 ◽  
Vol 5 (S2) ◽  
pp. 516-517
Author(s):  
Lucille A. Giannuzzi
Keyword(s):  
Cross Sections ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Subsequent Development ◽  
Bulk Sample ◽  
Specimen Preparation ◽  
Tem Analysis ◽  
Plan View ◽  
Area Of Interest ◽  
Wide Range

The focused ion beam (FIB) instrument has been developed and exploited by the microelectronics arena for specimen preparation for both scanning and transmission electron microscopy (TEM). The inception [1] and subsequent development [2] of the FIB TEM lift-out (LO) technique has enabled electron transparent membranes of generally uniform thickness to be produced for TEM analysis. The primary advantage of the FIB technique is that site specific cross sections (or plan view sections [3]) may be fabricated quickly and reproducibly. The FIB LO technique has been used extensively in our laboratory for a wide range of materials [4] and biological applications [5] which are summarized in figure 1.The FIB LO method consists of milling a series of trenches around an area of interest. Then the bulk sample is tilted up to ∼60 degrees to allow the beam to impinge on the lower portion of the specimen surface so that cuts can be made along the bottom edge and the lower 2/3 of the distance up one side of the specimen.

Sign in / Sign up

Export Citation Format

Share Document