Tear and tensile strength development of PGW and CTMP pulps mixed with PLA or viscose fibres

2014 ◽  
Vol 29 (2) ◽  
pp. 304-308 ◽  
Author(s):  
Jaakko Asikainen ◽  
Antti Korpela
Keyword(s):  
Tensile Strength ◽  
Fibre Length ◽  
Wood Fibre ◽  
Strength Development ◽  
Paper Properties ◽  
Mechanical Pulp ◽  
Tear Strength ◽  
Tear Index ◽  
Simultaneous Decrease ◽  
A Minor

Abstract The objective was to evaluate the effects on paper properties when replacing a minor share of wood fibre by synthetic fibre. The aim was to increase tear strength and stretch while minimizing the loss of tensile strength in paper consisting of mechanical pulp. Tested synthetic fibres included PLA and viscose fibres mixed with mechanical or chemi-mechanical pulp. Even at relatively low proportions, the synthetic fibres contributed to a significant increase of tear strength in the wood fibre based papers. With the highest tested proportion (20%) the increase of tear index in PGW based stock was 243% with PLA and 177% with viscose fibre. However, a simultaneous decrease in tensile strength and tensile stiffness was observed. The stretch at break remained unchanged. Thickness reduction of the synthetic fibres resulted in an increase of tear strength. The effect is due to the high fibre length of synthetic fibres, producing mechanically well entangled networks, coupled with the high enough strength of the synthetic fibres.

scholarly journals Comparison of two bar edge lengths of refining plates on the properties of American old corrugated container pulp during low consistency refining

BioResources ◽  
2019 ◽  
Vol 15 (1) ◽  
pp. 347-359
Author(s):  
Hui Cai ◽  
Zhaoyang Yuan ◽  
Guolin Tong ◽  
Xin Zhang ◽  
Hui Zhang
Keyword(s):  
Tensile Strength ◽  
Specific Energy ◽  
Lower Energy ◽  
Energy Input ◽  
Fibre Length ◽  
Strength Properties ◽  
Strength Development ◽  
Low Intensity ◽  
Plate Geometry ◽  
Length Reduction

Commercial American old corrugated container pulp (AOCC) boards were used as the starting material for repulping and low consistency (LC) refining to investigate the effects of LC refining plate geometry on the fibre and strength properties of the generated pulp. Specific refining energy that ranged from 0 to 120 kWh/air-dried ton (ADT) of pulp was explored for the two bar edge lengths (BEL) of refining plate patterns, wide 0.99 km/rev BEL and interim 2.01 km/rev BEL. The results showed that fibre length, curl index, kink index, and pulp freeness decreased while fines content increased with increasing refining energy input for both of the two refining plates during LC refining. LC refining with 2.01 BEL plate at low intensity of 0.24 J/m showed less fibre length reduction and more tensile strength development than that obtained with 0.99 BEL plate at high intensity of 0.48 J/m when compared at the same specific energy. Moreover, to achieve the desired tensile strength of the AOCC pulp, lower energy was needed for the interim 2.01 BEL plate than the wide 0.99 BEL plate. Thus, the interim 2.01 km/rev BEL refining plate provided potential for saving refining energy to reach a desired tensile strength of AOCC pulp.

Fibre characteristics and paper properties of formic acid / peroxyformic acid birch pulps

1997 ◽  
Vol 12 (4) ◽  
pp. 237-243 ◽  
Author(s):  
Anu Seisto ◽  
Krisriina Poppius-Levlin
Keyword(s):  
Tensile Strength ◽  
Formic Acid ◽  
Kraft Pulp ◽  
Strength Properties ◽  
Kappa Number ◽  
Strength Development ◽  
Paper Properties ◽  
Fibre Breakage ◽  
High Degree ◽  
Peroxyformic Acid

Abstract The fibre and paper properties of nine unbleached formic acid / peroxyformic acid (MILOX) pulps with kappa number 6-20 were studied and compared with a kraft pulp with kappa number 20. The degree of deformation was greater in the MILOX fibres, affecting the paper properties of the MILOX pulps. The large number of curl and kinks in the MILOX fibres were probably caused mechanically. The MILOX fibres showed greater conformability, resulting in higher paper density. The defects in the MILOX fibres were apparently so severe as to cause fibre breakage during PFI beating of the pulps. As a result of both fibre deformation and breakage, the tensile strengths of the MILOX pulps were lower than that of the reference kraft pulp, and tensile strength development during beating was slower. The tear strength of the best MILOX pulp was lower than that of the kraft pulp when compared at the same tensile index. Fibre deformation in both MILOX and the kraft pulp increased during bleaching. The kinks in the fibres were possibly set into position, giving the bleached MILOX pulps poorer bonding ability and lower paper density. A high degree of fibre defo~mation had the same effect on the tensile strength development of the bleached MILOX pulps as it did in the unbleached state. The light scattering properties of the MlLOX pulps were better than those of the kraft pulp, possibly due to the higher fines content of the MILOX pulps. The results indicate that more attention should be given to mechanical treatments during MILOX pulping in order to bring the strength properties closer to those of kraft pulp.

scholarly journals The Influence of La and Ce on Microstructure and Mechanical Properties of an Al-Si-Cu-Mg-Fe Alloy at High Temperature

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 384
Author(s):  
Andong Du ◽  
Anders E. W. Jarfors ◽  
Jinchuan Zheng ◽  
Kaikun Wang ◽  
Gegang Yu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Intermetallic Phases ◽  
High Temperature Strength ◽  
Thermal Expansion Mismatch ◽  
Strengthening Mechanisms ◽  
High Temperature Mechanical Properties ◽  
Minor Contribution ◽  
A Minor

The effect of lanthanum (La)+cerium (Ce) addition on the high-temperature strength of an aluminum (Al)–silicon (Si)–copper (Cu)–magnesium (Mg)–iron (Fe)–manganese (Mn) alloy was investigated. A great number of plate-like intermetallics, Al11(Ce, La)3- and blocky α-Al15(Fe, Mn)3Si2-precipitates, were observed. The results showed that the high-temperature mechanical properties depended strongly on the amount and morphology of the intermetallic phases formed. The precipitated tiny Al11(Ce, La)3 and α-Al15(Fe, Mn)3Si2 both contributed to the high-temperature mechanical properties, especially at 300 °C and 400 °C. The formation of coarse plate-like Al11(Ce, La)3, at the highest (Ce-La) additions, reduced the mechanical properties at (≤300) ℃ and improved the properties at 400 ℃. Analysis of the strengthening mechanisms revealed that the load-bearing mechanism was the main contributing mechanism with no contribution from thermal-expansion mismatch effects. Strain hardening had a minor contribution to the tensile strength at high-temperature.

scholarly journals Utilization of Leather Waste Fibers in Polymer Matrix Composites Based on Acrylonitrile-Butadiene Rubber

Polymers ◽  
2020 ◽  
Vol 13 (1) ◽  
pp. 117
Author(s):  
Le Thuy Hang ◽  
Do Quoc Viet ◽  
Nguyen Pham Duy Linh ◽  
Vu Anh Doan ◽  
Hai-Linh Thi Dang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Polymer Matrix Composites ◽  
Waste Product ◽  
Dynamic Mechanical Properties ◽  
Hammer Mill ◽  
Butadiene Rubber ◽  
Matrix Composites ◽  
Leather Industry ◽  
Tear Strength

In this study, we present the fabrication of nitrile butadiene rubber/waste leather fiber (NBR/WLF) composites with different weight percentages of WLF and NBR (0/100, 20/80, 30/70, 40/60, 50/50, 60/40 wt/wt). WLF was prepared by cutting the scrap leathers from the waste product of the Vietnamese leather industry. Subsequently, in order to make the short fibers, it was mixed by a hammer mill. The characteristics of WLF/NBR composites such as mechanical properties (tensile strength, tear strength, hardness), dynamic mechanical properties, toluene absorption, and morphology were carefully evaluated. As a result, the tensile strength and tear strength become larger with increasing WLF content from 0 to 50 wt% and they decrease when further increasing WLF content. The highest tensile strength of 12.5 MPa and tear strength of 72.47 N/mm were achieved with the WLF/NBR ratio of 50/50 wt%. Both hardness and resistance of the developed materials with toluene increased with increasing WLF content. The SEM results showed a good adhesion of NBR matrix and the WLF. The increasing of storage modulus (E’) in comparison with raw NBR showed good compatibility between WLF and NBR matrix. This research showed that the recycled material from waste leather and NBR was successfully prepared and has great potential for manufacturing products such as floor covering courts and playgrounds, etc.

Action Mechanism of the Improvement of Printability for Eucalypt Bleached Kraft Pulp Pretreated by Cellulase

2013 ◽  
Vol 779-780 ◽  
pp. 294-301
Author(s):  
Wan You Tang ◽  
Li Chen ◽  
Zheng Jian Zhang
Keyword(s):  
Tensile Strength ◽  
Fiber Length ◽  
Kraft Pulp ◽  
Pulp Fiber ◽  
Fiber Morphology ◽  
Strength Index ◽  
Bleached Kraft Pulp ◽  
Tear Index ◽  
Pulp Sample ◽  
The Mean

Enzymatic refining of eucalypt bleached kraft pulp with the cellulase NOV476 was studied. The effects of this cellulase on the physical properties of pulp, fiber morphology and fiber appearance of the eucalypt bleached kraft pulp in different application conditions were discussed. The results show that, with the increase in the amount of enzyme, tensile strength index, burst index and TEA index of paper are increased and then decreased; elongation and tear index of paper have been declining, Zeeil tensile strength index has been an upward trend. Without beating the pulp sample, gradually increases as the amount of enzyme, the average fiber length and the average fiber width are gradually reduced, while mean kink index substantially constant. Number of vessels in fiber overall reduced tendency reaches a minimum in the amount of enzyme 0.5μ/g, the phenomenon is most obvious. In the same conditions of beating time, gradually increases as the amount of enzyme, the average fiber length is gradually reduced, an average fiber width is gradually increased, the mean kink index reaches a maximum in the amount of enzyme is 0.5μ/g. Number of vessels in fiber overall reduced trend.

scholarly journals Better Wettability of Pandanus Utilis Alkaline Treated Fibres Tead to Higher Tensile Strengths of Composites.

2021 ◽  
Author(s):  
Laurent L'Entete ◽  
Hareenanden Ramasawmy
Keyword(s):  
Tensile Strength ◽  
Composite Materials ◽  
Carbon Footprint ◽  
Fibre Length ◽  
Natural Fibre ◽  
Engineering Properties ◽  
Aggressive Treatment ◽  
High Carbon ◽  
Reinforcing Agent ◽  
Internal Angle

Abstract Composite materials made with synthetic fibres like E-glass, Kevlar or carbon have helped to provide a wide array of products to society with specific engineering properties. However, these materials have a high carbon footprint as well as being non-biodegradable. The use of natural fibre, as a substitution to these man-made fibres, has been studied and encouraging results are being obtained.In this study, the use of ‘Pandanus utilis’ fibre as a reinforcing agent in plastic was investigated with the aim of exploring specific properties such as the tensile strength of the fibre, its wettability and the effect of fibre length after treating the fibre with two different NaOH solutions. Results have shown that better reinforcement was obtained for the composites (11.10 ± 2.53MPa) with fibres subjected to a more aggressive treatment (2.5%NaOH for 2h) compared to the composite made with fibres having maximum tensile strength (168 ± 12MPa at 0.5% NaOH for 14h), due to a better hydrophilicity of the alkaline treated fibre (87.37° internal angle). Within the range of short chopped fibre length tested (6 to 15 mm), it was shown that there was a general decrease in the tensile strength of the composite.

APPROACHES TO CONTROLLING MICRO-ORGANISMS IN COTTON AND COTTON/ELASTANE CLOTHINGS

2021 ◽  
Vol 16 (3) ◽  
pp. 124-135
Author(s):  
Nilüfer Yıldız Varan
Keyword(s):  
Mechanical Properties ◽  
Antimicrobial Activity ◽  
Tensile Strength ◽  
Untreated Control ◽  
Physical And Mechanical Properties ◽  
Emergency Rooms ◽  
Tear Strength ◽  
Antifungal Properties ◽  
Micro Organisms ◽  
Control Samples

Antimicrobials are substances or mixtures of substances used to destroy or suppress the growth of harmful microorganisms such as bacteria, viruses, or fungi on inanimate objects and surfaces. In this study, an alternative method is presented using triclosan agents that can kill bacteria and viruses to help keep patient, operating, and emergency rooms free of germs. Samples were treated with triclosan to achieve antimicrobial/antiviral/antifungal properties for further designs to help comfort and bacteria, virus, fungi (BVF) resistantance during use. The physical, and mechanical properties of triclosan treated cotton and cotton/elastane fabrics in comparison with untreated control samples was investigated. The results showed that a small significant decrease was observed for tensile strength (strip and grab methods), tear strength and seam strength. Besides, statistically a small significant decrease was observed with the increase in triclosan concentration for all samples. The panama weaves showed the lowest tensile strength and the highest tear strength and statistically small significant decrease was observed for all treated samples. The antimicrobial tests showed that all treated samples have a very good antimicrobial activity which can also lead to antivirus protection by providing hygienic environment for the users during future designs.

Effect of abrasive particle size on tribological behavior of elastomers

2019 ◽  
Vol 234 (3) ◽  
pp. 373-385 ◽  
Author(s):  
F Hakami ◽  
A Pramanik ◽  
AK Basak ◽  
N Ridgway ◽  
MN Islam
Keyword(s):  
Particle Size ◽  
Tensile Strength ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Abrasive Particle ◽  
Tribological Behaviour ◽  
Elongation At Break ◽  
Tear Strength ◽  
Wear And Friction ◽  
Abrasive Size

Effect of abrasive particle size on tribological behaviour of different elastomers was investigated experimentally in this study. The size of abrasive particle size was varied from coarse (425 µm) to fine (82 µm). Wear rate and coefficient of friction were calculated and analyzed accordingly followed by the examination of worn surfaces by a scanning electron microscope to unravel the wear mechanism. Experimental results showed that abrasive size had a significant effect on wear and friction behaviour of the elastomers. As the abrasive particle size increased, wear rate and coefficient of friction also increased at different rates and exhibited different wear mechanisms that changed from friction to fatigue and roll formation. Mechanical properties of elastomers such as hardness, tensile strength, tear strength, and elongation at break also contributed to wear and friction. The effect of elongation at break and tensile strength on wear rate is more pronounced at lower abrasive particle size, whereas hardness and tear strength play a pivotal role at the higher abrasive size.

Sign in / Sign up

Export Citation Format

Share Document