scholarly journals Testing of Nutmeg Shell as a Normal Concrete Material in Terms of Volume Weight and Compressive Strength Value

2021 ◽  
Vol 21 (3) ◽  
pp. 129-138
Author(s):  
Keyword(s):  
Compressive Strength ◽  
Specific Gravity ◽  
Concrete Aggregate ◽  
Fine Aggregate ◽  
Normal Concrete ◽  
Concrete Material ◽  
Average Value ◽  
Volume Weight ◽  
Compressive Strength Of Concrete

Normal concrete uses fine aggregate and coarse aggregate with concrete density 2200 kg/m3-2400 kg/m3 with a compressive strength of about 15-40 MPa [1]. The purpose of this study is to determine characteristics of the concrete aggregate and the compressive strength of the concrete design based on the DOE (Department of Environment) method and the SNI Standard. In this research, the use of nugmet shell was varied as follows: 0%, 0,25%, 0,50%, 0,75% and 1% of the cement weight. The results showed that the use of nutmeg shells as a normal concrete affected the specific gravity and the value compressive strength of concrete. The higher the percentage of nutmeg shells, the lower the specific gravity and compressive strength of the concrete. The average value of density to nutmeg shell concrete (NSC) 2254.72 (kg/m3) and normal concrete 2304.32 (kg/m3). The compressive strength of normal concrete is 224.2 kg/cm2 and the nutmeg shell concrete (NSC) the composition of 0.25% and 0.5% obtained by 129.6 kg/cm2 and 140.0 kg/cm2 increases the use of nutmeg shell 0.75% and 1% obtained value ​​of 117.6 kg/cm2 and 118.1 kg/cm2 decreased at the age of 28 days. The compressive strength of normal concrete 22 MPa while the maximum nutmeg shell concrete (NSC) 14 MPa, so it does not meet the quality of normal concrete in general.

scholarly journals Penggunaan Limbah Nikel Sebagai Material Subtitusi Agregat Kasar Pada Beton K.250

2021 ◽  
Vol 2 (1) ◽  
pp. 29-36
Author(s):  
Muhammad Muhsar ◽  
Abdul Kadir ◽  
Sulaiman Sulaiman
Keyword(s):  
Compressive Strength ◽  
Los Angeles ◽  
Specific Gravity ◽  
Moisture Content ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Test Standards ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

The purpose of this study was to Analyze the characteristics of theaggregates used in concrete mixtures and analyze how muchincrease in compressive strength of concrete with a variation ofnickel slag substitution 0%, 5%, 15%, 25% compared with normalconcrete. The characteristics of the material examined are watercontent, sludge content, specific gravity and absorption, volumeweight, abrasion with los angeles machines, and filter analysis.While the large increase in compressive strength of concrete can betested at the age of 7 days, 14 days, 28 days and 35 days. From the results of the analysis of the characteristics of nickel slagwaste in concrete mixes meet the test standards in concretemixtures, with a moisture content of 0.86%, sludge content of 0.44%,specific gravity of 2.94 gr / cm3, volume weight of 1.76 gr / cm3,abrasion 36.07%. And a large increase in compressive strength ofconcrete with a variation of nickel slag substitution of 0%, 5%, 15%,25% compared to normal concrete is increasing. The highestpercentage increase in concrete compressive strength is found inconcrete compressive strength between a variation of 15% with avariation of 25% at 14 days concrete age, with a percentage increasein value of 13.13%.

scholarly journals ANALISA KUAT TEKAN BETON MENGGUNAKAN PASIR APUNG

2018 ◽  
Vol 1 (1) ◽  
Author(s):  
Abdul Gaus ◽  
Imran Imran ◽  
Liska Novianti
Keyword(s):  
Compressive Strength ◽  
Specific Gravity ◽  
Volcanic Glass ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Concrete Mix ◽  
Pumice Sand ◽  
Compressive Strength Of Concrete

Pumice sand is a bright colored butian type, containing foam made from glass-walled bubbles andusually referred to as silicate volcanic glass granules. This pumice sand can be used as a substitutefor normal sand as fine aggregate in a mixture of concrete mix. Based on the characteristic testexamination, it can be seen that in testing the characteristics of pumice sand to the specificationsof normal sand in specific gravity testing and weight testing of quicksand obtained results thatare smaller than the specifications of normal sand and absorption tests obtained results greaterthan specifications on normal sand. The results of the normal sand compressive strength at BN is250.95 kg /cm2 while the results of the floating sand concrete compressive strength on BPA is224, 965 kg /cm2. Based on the research it can be concluded that with the same quality of concrete,the quality of K-250 is different in comparison to the compressive strength of concrete in normalsand and pumice sand concrete shows almost the same results. Therefore, more in-depth researchis needed regarding the use of pumice sand instead of normal sand in a mixture of concrete mix.

scholarly journals ANALISIS PENGARUH PENAMBAHAN AGREGAT LIMBAH PLASTIK (POLYETHYLENE TEREPHATHALATE) TERHADAP KUAT TEKAN BETON

2021 ◽  
Vol 3 (3) ◽  
pp. 243-252
Author(s):  
Masril Masril ◽  
Jefry Rizaldo
Keyword(s):  
Compressive Strength ◽  
Rural Areas ◽  
Plastic Material ◽  
Plastic Waste ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Food And Beverage ◽  
Compressive Strength Of Concrete

Plastic Material Plastic waste is a problem that is very often encountered in urban and rural areas. The use of plastic in each year will continue to increase because food and beverage products all use materials made of plastic. However, the plastic in question is plastic that is difficult to contaminate with soil or commonly referred to as inorganic waste, which is difficult to self-destruct. This is what causes the amount of plastic waste to increase.Therefore, to reduce this waste, the volume of this waste is used in the development. Besides, the grain gradation of the aggregate has been determined with the aim of obtaining an increase in the compressive strength of the concrete with the addition of plastic waste. The quality of the concrete to be examined by the authors in this study is fc = 14.5 MPa. In other words, in this study the author tries to compare the compressive strength of concrete between normal concrete and concrete mixed with plastic waste. In this study also used a variation of plastic waste substitution with a ratio of 0%, 5%, 10% to the volume of fine aggregate. For each variation, 2 samples were used which included normal concrete so that the total test object used was 12 tested at 7 days, 14 days and 28 days of concrete.From the results of testing the compressive strength of concrete against normal concrete and mixed concrete with sawdust surian at the age of 28 days, the normal concrete compressive strength is 14.5 MPa, while in the sawdust mixture with a percentage of 5%, the concrete compressive strength is 14.14 MPa. 10% obtained a compressive strength of 17.05 MPa. From this test, it can be concluded that from each of the percentages that are made, the compressive strength increases along with the percentage of the amount of plastic waste added to the concrete mixture. In other words, the greater the percentage of plastic waste used, the higher the compressive strength and quality of the concrete produced.

scholarly journals THE EFFECT OF ADDING CEMENT WASTE ON THE QUALITY OF CONCRETE COMPRESSIVE

Jurnal CIVILA ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 213
Author(s):  
Asrul Majid ◽  
Hammam Rofiqi Agustapraja
Keyword(s):  
Compressive Strength ◽  
Strength Test ◽  
Fine Aggregate ◽  
Infrastructure Development ◽  
Test Results ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Concrete Materials ◽  
Test Objects

Infrastructure development is one of the important aspects of the progress of a country where most of the constituents of infrastructure are concrete. The most important constituent of concrete is cement because its function is to bind other concrete materials so that it can form a hard mass. The large number of developments using cement as a building material will leave quite a lot of cement bags.In this study, the authors conducted research on the effect of adding cement waste to the compressive strength of concrete. This study used an experimental method with a total of 24 test objects. The test object is in the form of a concrete cylinder with a diameter of 15 cm and a height of 30 cm and uses variations in the composition of the addition of cement waste cement as a substitute for fine aggregate, namely 0%, 2%, 4% and 6%. K200). The compressive strength test was carried out at the age of 7 days and 28 days.The test results show that the use of waste as a partial substitute for fine aggregate results in a decrease in the compressive strength of each mixture. at the age of 7 days the variation of 2% is 16.84 MPa, 4% is 11.32 MPa and for a mixture of 6% is 6.68 MPa. Meanwhile, the compressive strength test value of 28 days old concrete in each mixture decreased by ± 6 MPa. So the conclusion is cement cement waste cannot be used as a substitute for fine aggregate in fc 16.6 (K200) quality concrete because the value is lower than the specified minimum of 16.6 MPa.

scholarly journals Analysis Of Use Sea Sand as A Fine Aggregate Replacement To Strong Press Concrete

2021 ◽  
Vol 1 (3) ◽  
pp. 1-6
Author(s):  
Fachrul Arya Sanjaya ◽  
Sapto Budy Wasono ◽  
Diah Ayu Restuti Wulandari
Keyword(s):  
Compressive Strength ◽  
Building Material ◽  
Fine Aggregate ◽  
River Sand ◽  
Concrete Material ◽  
Sea Sand ◽  
Concrete Cylinders ◽  
Compressive Strength Of Concrete ◽  
Average Compressive Strength

Concrete is a composite building material made from a combination of aggregate and cement. The limitation of concrete material, in this case, is a fine aggregate (river sand). The utilization of sea sand as an alternative to fine aggregate in the manufacture of concrete is     motivated by the availability of sea sand in nature in very large quantities. This study aims to determine the comparison and how much the compressive strength of concrete produced when using sea sand. The test was carried out when the specimens were 7, 14, and 28 days old with the specimens used in this study were concrete cylinders with a diameter of 15 cm and a height of 30 cm. The results showed that the use of sea sand as a substitute for fine aggregate showed an average compressive strength in 7 days of 18.86 MPa, an average compressive strength of 14 days of 25.52 MPa, an average compressive strength of 28 days of 29.00 MPa. Then for the average compressive strength value of the use of river sand in 7 days is 17.17 MPa, the average compressive strength of 14 days is 23.24 MPa, the average compressive strength of 28 days is 26.41 MPa.

scholarly journals Lightweight Concrete With Mixed Foam Agent, Polymer and Bonding to Reach 300 Kg/Cm²

2020 ◽  
Vol 3 (1) ◽  
pp. 55-63
Author(s):  
Siti Rukmayani Japar ◽  
Freedy Kurniawan
Keyword(s):  
Compressive Strength ◽  
Specific Gravity ◽  
Lightweight Concrete ◽  
Agent Technology ◽  
Efficiency Coefficient ◽  
Light Weight ◽  
Normal Concrete ◽  
Earthquake Effect ◽  
Concrete Quality

Lightweight concrete is very much developed because of its benefits that can reduce the weight of the building itself, so that the earthquake effect on buildings can be minimized. By using Foam Agent Technology, it will add air pores which can reduce the specific gravity of normal concrete. To achieve the K 300 Concrete Quality with Light Weight, the researchers added Polymer and Polymer and Bonding mixture to the Concrete mixture using Foam Agent technology. From the research conducted by researchers, it was found that Foam Agent is able to help concrete become lighter by 13%. This research was also able to obtain the optimum compressive strength results with a light weight, the Light Concrete study with the addition of Foam Agent, Polymer and Bonding with a quality of 267 kg / cm² or equivalent to Fc 22 with a weight of 1877 Kg / cm³ and an efficiency coefficient of 14% which is higher than normal Concrete K 300 with a magnitude of 13%.

scholarly journals PENGARUH PENAMBAHAN SILICA FUME DAN GLENIUM SKY TERHADAP KUAT TEKAN BETON K-400

2020 ◽  
Vol 6 (2) ◽  
Author(s):  
Sudirman Kimi ◽  
Abdullah Abuzar Alghafari
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
Test Object ◽  
Building Construction ◽  
Raw Material ◽  
Concrete Technology ◽  
Normal Concrete ◽  
Three Stages ◽  
Compressive Strength Of Concrete

In the development of concrete technology (Concrete Technology) today which is increasingly unceasingly, along with the development of the era hence the quality of concrete selection as the main raw material of building construction is very important. This research writer take silica fume and glenium sky as added concrete mixture to know the influence of the addition of silica fume and glenium sky to the compressive strength of concrete. The research is divided into three stages : material testing, test object making and test object. This research uses cube-shaped specimen with size 15x15x15 cm, with 5 variations, they are normal concrete, silica fume 5%, silica fume 5% + glenium sky 2%, silica fume 5% + glenium sky 4%, and silica fume 5% + glenium sky 6%, which every variations has 3 test specimens with 3 days, 7 days, and 28 days. From laboratorium testing, the characteristics of compressive strength of concrete at age 28 days of normal concrete is 407,2 Kg/Cm2, normal concrete with silica fume 5% is 418,5 Kg/Cm2, normal concrete with silica fume 5% + glenium sky 2% is 435,9 Kg/Cm2, normal concrete with silica fume 5% + glenium sky 4% is 451,9 Kg/Cm2, normal concrete with silica fume 5% + glenium sky 6% is 484,1 Kg/Cm2.

scholarly journals Pengaruh Cangkang Kerang Laut Terhadap Kuat Tekan Beton

2021 ◽  
Vol 2 (1) ◽  
pp. 46-54
Author(s):  
Neti Rahmawati ◽  
Irwan Lakawa ◽  
Sulaiman Sulaiman
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Building Materials ◽  
Coarse Aggregate ◽  
Fine Aggregate ◽  
Fine Aggregates ◽  
Concrete Quality ◽  
Compressive Strength Of Concrete ◽  
Physical Construction

Concrete is one of the most widely used building materials today interms of physical construction. Concrete is made from a mixture offine, coarse aggregate, cement, and water with a certain ratio, aswell as materials that are usually added to the concrete mixtureduring or during mixing, to changing the properties of concrete tomake it more suitable in certain jobs and more economical, can alsobe added with certain other mixed materials as needed if deemednecessary. Seashells can be used to mix concrete. This study aims todetermine whether the addition of shells aggregate shells in aconcrete mixture can affect the mechanical properties of concrete.The specimens used are in the form of cubes with a size of 15cm x 15cm x 15 cm, consisting of additional concrete coarse and fineaggregate with shell substitution percentage of 0%, 15%, 20% with atotal sample of 45, with the planned concrete quality of K225. Theuse of sea shells in increasing the compressive strength of concrete isbetter used as fine aggregate than coarse aggregate. The use of seashells as a substitute for fine aggregates achieves maximum resultsat 20% composition.

scholarly journals OPTIMIZING THE USE OF ROCK ASH AS FINE AGGREGATES WITH THE ADDITION OF ADDITIVES TO THE CONCRETE MIXTURE WITH A COMPRESSIVE STRENGTH OF 350 Kg/cm2

CI-TECH ◽  
2020 ◽  
Vol 1 (01) ◽  
pp. 45-48
Author(s):  
Triaswati ◽  
Srie Subekti ◽  
Sulchan Arifin ◽  
Febri Aditya
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Normal Concrete ◽  
Type D ◽  
Cylinder Test ◽  
Fine Aggregates ◽  
Stone Dust ◽  
Compressive Strength Of Concrete

Stone dust nowadays is a side product of the stone crushing industry, the quality of which is quite a lot that it becomes a waste that needs to be handled. This study is intended to find out the composition of stone dust by adding some additive substance type D and type F to reach a compressive strength of 350 kg/cm2. The variation of percentage of stone dust on the composition of concrete mixture is 0%, 20%, 40%, 60%, 80%, 100%. The design of concrete mixture composition refers to the procedure of making preparation of the normal concrete mixture. SNI 03-2384-1993. The size of the cylinder test object is 15 cm in diameter and 30 cm in height. The result of this research shows that the mixture using stone dust has quite an effect on the compressive strength of concrete. From the result of the experiment, it is shown that for compressive strength of 350 kg/cm2, we can use 100% of stone dust with a resulted compressive strength of 445 kg/cm2.

scholarly journals Pemanfaatan Hasil Pembakaran Limbah Cangkang Kelapa Sawit sebagai Bahan Pengganti Pasir pada Pembuatan Beton Normal

2017 ◽  
Vol 6 (1) ◽  
pp. 30-40
Author(s):  
Fauzi Rahman ◽  
Fathurrahman Fathurrahman
Keyword(s):  
Compressive Strength ◽  
Oil Palm ◽  
Chemical Elements ◽  
Normal Mixture ◽  
Normal Concrete ◽  
Strength Tests ◽  
Compressive Strength Of Concrete ◽  
Concrete Testing ◽  
Fresh Fruit Bunches

In 2015 the total area of oil palm plantations in Kalimantan reached 3.47 million Ha with a production of 8.12 million tons per year. Solid waste is in the form of fresh fruit bunches and palm shells. The result of combustion of oil palm shell waste in the form of boiler crust ash is a waste that has chemical elements SiO2, Al2O3, and CaO, with the content of these compounds can affect the strength of the concrete and can increase its strength. In this study, the quality of the concrete mix planned at 28 days is 23 MPa. Concrete testing included compressive strength tests carried out at 3 days, 7 days, 14 days, 28 days, 42 days and 56 days. Before making concrete samples, the mortar compressive strength is tested first by varying the boiler crust ash content by 0%, 15%, 25%, 35%, and 50% to obtain the optimum mixture. Based on the results of the analysis of compressive strength mortar obtained the optimum mixture of 15% for the manufacture of concrete that will be compared with normal concrete. The compressive strength of concrete with the optimum mixture at 28 days is 24.44 Mpa more than the compressive strength of the 23 Mpa plan. Concrete that has the highest compressive strength occurs at the age of 56 days is concrete with the normal mixture with a compressive strength of 34.44 Mpa higher than the compressive strength of concrete with an optimum mixture of 15% boiler crust ash which is 28.51 MPa.

Sign in / Sign up

Export Citation Format

Share Document