scholarly journals Structural Analysis and 3D Timber Spatial Structure Modeling

2021 ◽  
pp. 4-16
Author(s):  
Тatiana Budko ◽  
Lyudmila Lavrinenko2
Keyword(s):  
Software Package ◽  
Architectural Design ◽  
Structural Model ◽  
Nonlinear Effects ◽  
Information Model ◽  
Information Modeling ◽  
Long Span ◽  
Information Models ◽  
Dome Structure ◽  
Wooden Structures

The analysis of the structural form of the multi-volume dome structure using load-bearing wooden arches is performed. The complexity of the volumes and their connecting lines, as well as the requirement to conduct a non-linear analysis of long-span wooden elements at the request of Eurocode 5 make the information model necessary. It is noted that the design using this technology is developing in the direction of taking into account all stages of the structure  life cycle. Information modeling of wooden structures in the world is the most prepared for the use of BIM-technologies. This is due to the sophisticated digital technologies for the production   of modern wooden structures elements. An information model was formed for designing according to the regulations of Ukraine. The Information Model was created in the SAPFIR software package for further possibility of importing the model into the LIRA-CAD software package. The necessary auxiliary steps were used to build the model. The loads on the curved surface were calculated in the PC Espri. For further development of the nodes, 3D-modeling was used with the transfer of the information model into the PC Tekla Structures as a specialized environment for the constructive section of the project. The presented analysis of the complex dome structure using wooden arches summarizes the approaches to the development of unique forms of structures using wood. The use of information models has significantly increased the complexity of architectural design and structural model taking into account the nonlinear effects of wood. The possibility of integrating these tools for further implementation in BIM-technology is shown.

scholarly journals BIM-TECHNOLOGY METHOD AND MODELS IN THE DESIGN OF THE AQUAPARK DOME STRUCTURE WITH WOODEN ARCHES

2021 ◽  
pp. 72-84
Author(s):  
T.G. Budko ◽  
◽  
L.І. Lavrinenko ◽  
Keyword(s):  
Software Package ◽  
Local Coordinate System ◽  
Nonlinear Effects ◽  
Information Model ◽  
Information Modeling ◽  
Correct Orientation ◽  
Information Models ◽  
Dome Structure ◽  
Rigid Walls ◽  
Wooden Structures

Тhe issues of designing a multi-volume dome structure for a water park using wooden arches as load-bearing structures are сonsidered. The complexity of the volumes and their joining lines, as well as the requirement to perform non-linear analysis of large-span timber elements at the request of Eurocode 5, make an information model with elements of BIM-technology necessary. It is noted that design using this technology is developing in the direction of taking into account all stages of the structure life cycle. Wood Information modeling is the most prepared for the use of BIM-technologies. This is due to the high factory readiness and complex digital technologies for the manufacture of modern wooden structures elements. During the design, an information model was formulated in the SAPFIR software package with the subsequent possibility of importing the model into the LIRA-SAPR software package. Additional steps were used to build the model: creating a 2D template in AutoCad with reference lines and the location of rigid walls on which the coating rests, and importing drawings into SAPFIR as a dxf-underlay; for all elements of the system located in the local coordinate system, auxiliary lines were built for the correct orientation of the plane in space; loads on curved surfaces were calculated in the PC Expri. For the further development of the nodes, 3D modeling was used with the transfer of the information model to the Tekla Structures PC as a specialized environment for the constructive section of the project. The presented calculation of a complex dome structure using wooden arches summarizes the approaches to the development of unique forms of structures using wood. The use of information models made it possible to reduce the time spent on design, to optimize the drawings, and also to significantly increase the complexity of the architectural and structural design of the structure and the design model, taking into account the nonlinear effects of wood.

scholarly journals Information modeling of processes of reflexive management of herd behavior at enterprises

2019 ◽  
Keyword(s):  
System Analysis ◽  
Information Model ◽  
Information Modeling ◽  
Practical Implementation ◽  
Herd Behavior ◽  
Conceptual Information ◽  
Scientific Methods ◽  
Modeling Methodology ◽  
Information Models ◽  
General Scientific

The relevance of the practical implementation of the concept of modeling processes of reflexive management of herd behavior at enterprises, which is reduced to the construction of a conceptual information model, is substantiated. The subject of this research is the toolkit of information modeling of the processes of reflexive management of herd behavior at enterprises. The goal of the article is information modeling of the processes of reflexive management of herd behavior at enterprises. Objective: the construction of an information model of the mechanisms of reflexive management of herd behavior in enterprises in the context of the interrelated functions performed by the system in question and the relationship between data, where, among others, information communications are reflected. General scientific methods are used: system analysis – to determine the features of the mechanism of reflexive management of herd behavior at enterprises, structural (functional) analysis – to identify the main functions of the modeling system of processes of reflexive management of herd behavior at enterprises, information modeling methodology SADT (IDEF0 notation) – to develop information models of a system for modeling the processes of reflexive management of herd behavior at enterprises. The results are obtained: an information IDEF0 model of a system for modeling the processes of reflexive management of herd behavior based on the SADT methodology is developed, which allows you to get a holistic picture of the corresponding processes at enterprises, the basic system concepts of which form the basis of the future information system. Conclusions: formalization, within the framework of the information model of the basic functions of the mechanism of modeling the processes of reflexive management of herd behavior at the enterprise, allows us to describe the basic information connections in a logical, convenient and consistent form, present implementation mechanisms, a set of mathematical models and approaches of the corresponding system.

scholarly journals BUILDING INFORMATION MODELING AND OHAS

2015 ◽  
Vol 1 (1) ◽  
pp. 26-31
Author(s):  
Zdenka Hulínová ◽  
Jana Madová
Keyword(s):  
At Risk ◽  
Potential Risk ◽  
Architectural Design ◽  
Building Information Modeling ◽  
Civil Engineering ◽  
Occupational Injuries ◽  
Information Modeling ◽  
Design Information ◽  
Information Models ◽  
Building Information

Civil engineering is considered to be the area with the highest occurrence of occupational injuries. Workers perform plenty of activities that endanger their health and put them at risk of occupational injuries and diseases. There are many convincing proves that dangerous risk situations appear already in the early stages of project proposals. On the basis of this fact we can estimate that one of the most effective methods of preventing and reducing occupational injuries is elimination of potential risk at the very beginning, i.e. already in the architectural design. Information models BIM enable us to simulate the overall situation of the project both structurally and visually. Thanks to this fact we can prevent multiple problems occurring not only during the realisation phase, but during the usage of buildings as well.

Systematic Design Method for Information Modeling in CAD/CAE

2003 ◽  
Author(s):  
Sai Zeng ◽  
Edward J. Kim ◽  
Gregory M. Mocko ◽  
Angran Xiao ◽  
Russell Peak ◽  
...  
Keyword(s):  
Solid Mechanics ◽  
Design Method ◽  
Building Blocks ◽  
Information Model ◽  
Information Modeling ◽  
Systematic Design ◽  
Element Analysis ◽  
Design Models ◽  
Information Models ◽  
Analysis Models

As engineering systems are increasingly becoming more complex, the need for information models is growing accordingly. Extensive research is currently underway to develop engineering data management capabilities and to understand the role of information as a systems integrator. In order to develop information models more effectively, a systematic methodology is needed to better manage data and develop information models. In the area of CAD/CAE/CAM applications, an information gap exists between design models and analysis models. To this end, a multi-representational architecture (MRA) is presented to facilitate the transformation of information from design models to various support analysis models. In this paper, our primary focus is on ABBs (Analysis Building Blocks) for solid mechanics and thermal systems that generate FEA (Finite Element Analysis) SMMs (Solution Method Models) to obtain their results. Our focus in this paper is to investigate the effectiveness of the Pahl and Beitz methodology in developing the ABB information model. The Pahl and Beitz design methodology is intended for physical product design applications. Three of the four phases of the Pahl and Beitz methodology are examined and modified to facilitate development of the ABB information model. The augmentations of these phases are presented in this paper. The results of the development of concepts of ABB information model using the Pahl and Beitz methodology support the use of systematic design methodologies for the development of information models. The emphasis of this work is on the methodology used to develop the ABB information model rather than the technical result of the ABB model.

The creation of information models of roads on the basis of research with the use of global systems and remote sensing techniques

2021 ◽  
pp. 102-107
Author(s):  
A.A. NERETIN ◽  
◽  
I.I. POZNIAK ◽  
Keyword(s):  
Remote Sensing ◽  
3D Model ◽  
Information Model ◽  
Information Modeling ◽  
Digital Model ◽  
The Road ◽  
Information Models ◽  
Remote Sensing Techniques ◽  
Transfer Of Information ◽  
Global Systems

Information modeling allows you to move to the end-to-end transfer of information from surveys to designers, then to builders, and then to operational services. The information 3D model begins to be formed at the stage of research in the form of an information digital model, then a project information model of the road is created on its basis

scholarly journals Information modeling of the construction and demolition waste system

2019 ◽  
Vol 97 ◽  
pp. 01020
Author(s):  
Alexander Ginzburg
Keyword(s):  
Smart Cities ◽  
Information Model ◽  
Information Modeling ◽  
Construction And Demolition Waste ◽  
Steady Increase ◽  
Demolition Waste ◽  
Information Models ◽  
Effective Organization ◽  
Construction Forecasting ◽  
Intensive Development

Throughout the world, the intensive development of production is accompanied by a steady increase in waste generation. Ecological problems, problems of utilization and recycling of waste come to the fore. The effective functioning of the construction complex is largely determined by the effective organization of the construction and demolition waste (CDW) circulation. Considering the scale of construction, forecasting the volume of waste formation in order to effectively organize the system of economic turnover of CDW is a very relevant scientific and practical problem. Management of CDW flows in Smart cities should be based on information models containing the necessary data on the types, forms and volumes of waste. The paper presents such an information model and a mathematical method of predicting the formation of the CDW. Information modeling of the composition and volume of CDW formation allows on the basis of the developed mathematical apparatus to provide an analysis of construction development trends. It allows to carry out construction production operational and strategic planning and management in terms of the CDW formation, processing and disposal. Analysis of the construction, reconstruction and demolition CDW volume dynamics information model is the basis for further design of treatment plants future scheme.

Information Models for Document Engineering

2011 ◽  
pp. 285-302
Author(s):  
James A. Thom
Keyword(s):  
Design Process ◽  
Data Model ◽  
Unified Modeling Language ◽  
Information Model ◽  
Structured Data ◽  
Information Modeling ◽  
Modeling Language ◽  
Semantic Data ◽  
Information Models ◽  
Entity Relationship

Software engineers develop an information model in the systems analysis and design process to represent the concepts, specification or implementation design of a software system (Fowler and Scott, 1997). This information model is designed using a modeling language such as the Unified Modeling Language (UML) defined by Rumbaugh, Jacobson, and Booch (1999). The software is implemented by translating the information model into code. Similarly, data engineers develop an information model in the database design process to represented the types of data to be stored in a database. This conceptual information model is typically defined using one of the semantic data modeling languages (Hull and King, 1987) such as Entity-Relationship diagrams (Chen, 1976), or NIAM conceptual schemas (Leung and Nijssen, 1988). The database is implemented by translating the information model into a database schema (defined using an implementation data model such as the relational data model or an object-oriented data model). Likewise, document engineers will develop an information model when designing the structure of a collection of documents. This information model will be implemented by translating it into a document schema. Traditional database information modeling has dealt with structured data such as that found in relational databases. However, much of the information produced using and stored in computers involves documents that do not contain data with a fixed structure - rather it is referred to as semi-structured data. The need for better modeling of documents is no more apparent than in the rapid and chaotic development over the last few years of the World Wide Web. In response to this need, various information models have been proposed to model the semi-structured data found in documents.

scholarly journals Justification of the architecture of an interactive information model of the process of space-mission vehicle launch preparation

2019 ◽  
Vol 18 (3) ◽  
pp. 118-130
Author(s):  
A. E. Privalov ◽  
P. Yu. Bugaichenko
Keyword(s):  
Situational Awareness ◽  
Information Model ◽  
Space Mission ◽  
Information Modeling ◽  
Maximum Efficiency ◽  
Preparation Process ◽  
Stage Of Development ◽  
Information Models ◽  
Technical Specifications ◽  
High Dynamics

The article presents a solution of the problem of substantiating the architecture of an interactive information model for the launch preparation of an integrated launch vehicle (ILV). The relevance of the research is due to the complexity and high dynamics of the ILV launch preparation process, as well as the latest achievements in the field of information modeling and decision support theory. The aim of the research is to raise the situational awareness of the decision maker in managing the process of preparing ILV for launch. The process of formation of situational awareness as an integral part of the decision-making process is analyzed. On the basis of this analysis a model of an indicator of the effectiveness of situational awareness formation is proposed for the first time. A model for evaluating the effectiveness of the process under study is developed on the basis of the mathematical apparatus of the theory of continuous-time Markov chains. The results of numerical experiments confirming the adequacy of the model and making it possible to state the quantitative requirements for the process of formation of situational awareness, ensuring its maximum efficiency, are presented. The tasks of the information system aimed at satisfying the requirements are stated, and the architecture of the information model of the ILV launch preparation process is developed. The research results can be used to justify the quantitative requirements for the developed information models of the launch situation at the stage of development of technical specifications.

scholarly journals Information models of structures and modeling in construction

2021 ◽  
Vol 274 ◽  
pp. 09016
Author(s):  
Vladimir Sokolnikov ◽  
Irina Osipenkova ◽  
Olga Stupakova ◽  
Roman Motylev ◽  
Roza Nurgalina
Keyword(s):  
Theoretical Models ◽  
Information Model ◽  
Scientific Basis ◽  
Point Of View ◽  
Information Modeling ◽  
Analytical Models ◽  
Information Models ◽  
Scientific Technical ◽  
Actual Field ◽  
Concept Of Information

The study of the basics of modeling of technical processes and objects forms the scientific basis for substantiating theoretical conclusions and postulates, classifying and developing the structures of theoretical models and justifying practical methods of preparation and implementation of (construction) production, which, in turn, influence the adoption of legal and regulatory innovations and statements. The article analyzes the types of modeling and models, scientific, technical, legal and regulatory contexts of the use of the concepts of «information modeling» in construction, and compares them with classical methods and tasks of modeling technical systems in solving scientific and engineering problems. The classification of scientific methods of modeling and models of technical objects and systems in construction is carried out. Examples of analytical models from the point of view of their classification and purpose are considered. It is shown that in the absence of clear scientific definitions of the concepts of «information», «model» and «modeling», given in terms of the actual field of knowledge, or application, the concept of «information model» comes into conflict with scientific and engineering ideas about the properties and purpose of the model. An approach is proposed to avoid the misuse of the concepts of «model» and « modeling».

scholarly journals Integration of tracking sensor technology into the information modeling of buildings and structures

2019 ◽  
pp. 1-1
Author(s):  
Tatyana A. Sivak ◽  
Pauline Yu. Kvasha
Keyword(s):  
Laser Scanning ◽  
Information Model ◽  
Information Modeling ◽  
Sensor Technology ◽  
Modern World ◽  
The Real ◽  
Information Models ◽  
Real Model ◽  
Image Monitoring ◽  
Real Building

Introduction. The issue of communication of information model of structure with real building is under consideration. This matter includes damage and various impacts both inside and outside the building tracking tools and techniques. With the help of the adoption of information modeling technologies in the Russian construction industry, maintenance and reconstruction of structures will reach a new level. For this purpose, it is necessary to understand the technology of communication of the information model with the real building, which is carried out by means of nanosensors installed throughout the structure. Materials and Methods. Available research papers about integration of BIM into the process of real construction are analyzed and the urgency and necessity of development of the given industry in the modern world are proved. Results. Application of information model in reconstruction of architectural engineering sites is investigated. The technique of real model scanning of a building for the creation of information model is presented. The examples of nanosensors use for synchronization of the real construction site with its information model are given. The importance of orientation in the building using GIS and BIM communication has been established. In this review, I would like to show the importance of information modeling for Russia. Conclusions. The opportunity to combine such technologies as photogrammetry, laser scanning and ReCap software features with automated monitoring of images taken from various devices is presented. It was concluded that it is possible to integrate a single information field into the area of laser scanning and the area of combination of technologies of detection and determination of light range and BIM construction. It is proposed to combine technologies of detection and cloud access to information models with radio-frequency identifiers. Possibility of integration of three technologies is revealed: BLE-sensors, RFID-scanners and automated image monitoring in the area of BIM damage assessment after earthquakes.

Sign in / Sign up

Export Citation Format

Share Document