scholarly journals Wettability and nanostructure effect on oscillating heat pipes

2015 ◽  
Author(s):  
◽  
Feng Zhao Zhang
Keyword(s):  
Heat Transfer ◽  
High Heat ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Oscillating Heat Pipe ◽  
Maximum Heat Transfer ◽  
Heat Transfer Limit ◽  
Efficient Heat Transfer ◽  
Oscillating Motion ◽  
Transfer Device

As electronics technologies rapidly develop with a demand for more power and miniaturization, effective thermal management of these systems becomes much more important. The oscillating heat pipe (OHP) is a promising highly efficient heat transfer device that is great for high heat flux applications common in the electronics industry. In the current investigation, the wettability effect on the heat transfer performance of OHPs has been conducted. 1). The overall performance of configuration of hydrophilic evaporator/ hydrophobic condenser and hydrophobic evaporator/ hydrophilic condenser was worse than the nontreated OHP, however; the oscillations were much damper when comparing the amplitudes. 2). High oscillating motion occurs in the OHP with the hydrophilic surface while low oscillating motion occurs in the untreated OHP. 3). A mathematical model shows that contact angle increases the oscillating motion decreases. 4). A theoretical model predicting operating limit is developed. Results show that radius and charging ratio has a large effect on the maximum heat transfer limit. Working fluids changes the operating limit.

Enhanced Pool Boiling Performance on Micro-, Nano-, and Hybrid-Structured Surfaces

2011 ◽  
Author(s):  
Qian Li ◽  
Wei Wang ◽  
Chris Oshman ◽  
Benoit Latour ◽  
Chen Li ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Thermal Management ◽  
Pool Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Structured Surfaces ◽  
Maximum Heat Transfer ◽  
Functional Components

Thermal management plays an important role in both high power electronics and energy conversion systems. A key issue in thermal management is the dissipation of the high heat flux generated by functional components. In this paper, various microstructures, nanostructures and hybrid micro/nano-structures were successfully fabricated on copper (Cu) surfaces, and the corresponding pool boiling heat transfer performance was systematically studied. It is found that the critical heat flux (CHF) of hybrid structured surfaces is about 15% higher than that of the surfaces with nanowires only and micro-pillars only. More importantly, the superheat at CHF for the hybrid structured surface is much smaller than that of the micro-pillared surface (about 35%), and a maximum heat transfer coefficient (HTC) of about 90,000W/m2K is obtained. Compared with the known best pool boiling performance on biporous media, a much larger HTC and much lower superheat at a heat flux of 250W/cm2 have been obtained on the novel hybrid-structured surfaces.

Heat Transfer Enhancement in Compact Phase Change Microchannel Heat Exchangers for High Flux Laser Diodes

2018 ◽  
Author(s):  
Jensen Hoke ◽  
Todd Bandhauer ◽  
Jack Kotovsky ◽  
Julie Hamilton ◽  
Paul Fontejon
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Flow Boiling ◽  
Laser Diodes ◽  
High Heat ◽  
Heat Fluxes ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Average Maximum

Liquid-vapor phase change heat transfer in microchannels offers a number of significant advantages for thermal management of high heat flux laser diodes, including reduced flow rates and near constant temperature heat rejection. Modern laser diode bars can produce waste heat loads >1 kW cm−2, and prior studies show that microchannel flow boiling heat transfer at these heat fluxes is possible in very compact heat exchanger geometries. This paper describes further performance improvements through area enhancement of microchannels using a pyramid etching scheme that increases heat transfer area by ∼40% over straight walled channels, which works to promote heat spreading and suppress dry-out phenomenon when exposed to high heat fluxes. The device is constructed from a reactive ion etched silicon wafer bonded to borosilicate to allow flow visualization. The silicon layer is etched to contain an inlet and outlet manifold and a plurality of 40μm wide, 200μm deep, 2mm long channels separated by 40μm wide fins. 15μm wide 150μm long restrictions are placed at the inlet of each channel to promote uniform flow rate in each channel as well as flow stability in each channel. In the area enhanced parts either a 3μm or 6μm sawtooth pattern was etched vertically into the walls, which were also scalloped along the flow path with the a 3μm periodicity. The experimental results showed that the 6μm area-enhanced device increased the average maximum heat flux at the heater to 1.26 kW cm2 using R134a, which compares favorably to a maximum of 0.95 kw cm2 dissipated by the plain walled test section. The 3μm area enhanced test sections, which dissipated a maximum of 1.02 kW cm2 showed only a modest increase in performance over the plain walled test sections. Both area enhancement schemes delayed the onset of critical heat flux to higher heat inputs.

Thermal Analysis of Cold Plate for Direct Liquid Cooling of High Performance Servers

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Bharath Ramakrishnan ◽  
Yaser Hadad ◽  
Sami Alkharabsheh ◽  
Paul R. Chiarot ◽  
Bahgat Sammakia
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Thermal Resistance ◽  
High Heat ◽  
High Heat Flux ◽  
Cold Plate ◽  
Liquid Cooling ◽  
Maximum Heat ◽  
Effective Heat ◽  
Cold Plates

Data center energy usage keeps growing every year and will continue to increase with rising demand for ecommerce, scientific research, social networking, and use of streaming video services. The miniaturization of microelectronic devices and an increasing demand for clock speed result in high heat flux systems. By adopting direct liquid cooling, the high heat flux and high power demands can be met, while the reliability of the electronic devices is greatly improved. Cold plates which are mounted directly on to the chips facilitate a lower thermal resistance path originating from the chip to the incoming coolant. An attempt was made in the current study to characterize a commercially available cold plate which uses warm water in carrying the heat away from the chip. A mock package mimicking a processor chip with an effective heat transfer area of 6.45 cm2 was developed for this study using a copper block heater arrangement. The thermo-hydraulic performance of the cold plates was investigated by conducting experiments at varying chip power, coolant flow rates, and coolant temperature. The pressure drop (ΔP) and the temperature rise (ΔT) across the cold plates were measured, and the results were presented as flow resistance and thermal resistance curves. A maximum heat flux of 31 W/cm2 was dissipated at a flow rate of 13 cm3/s. A resistance network model was used to calculate an effective heat transfer coefficient by revealing different elements contributing to the total resistance. The study extended to different coolant temperatures ranging from 25 °C to 45 °C addresses the effect of coolant viscosity on the overall performance of the cold plate, and the results were presented as coefficient of performance (COP) curves. A numerical model developed using 6SigmaET was validated against the experimental findings for the flow and thermal performance with minimal percentage difference.

A Numerical Model of a Reciprocating-Mechanism Driven Heat Loop for Two-Phase High Heat Flux Cooling

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Olubunmi Popoola ◽  
Ayobami Bamgbade ◽  
Yiding Cao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Numerical Model ◽  
Performance Optimization ◽  
Numerical Study ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Transfer Device

An effective design option for a cooling system is to use a two-phase pumped cooling loop to simultaneously satisfy the temperature uniformity and high heat flux requirements. A reciprocating-mechanism driven heat loop (RMDHL) is a novel heat transfer device that could attain a high heat transfer rate through a reciprocating flow of the two-phase working fluid inside the heat transfer device. Although the device has been tested and validated experimentally, analytical or numerical study has not been undertaken to understand its working mechanism and provide guidance for the device design. The objective of this paper is to develop a numerical model for the RMDHL to predict its operational performance under different working conditions. The developed numerical model has been successfully validated by the existing experimental data and will provide a powerful tool for the design and performance optimization of future RMDHLs. The study also reveals that the maximum velocity in the flow occurs near the wall rather than at the center of the pipe, as in the case of unidirectional steady flow. This higher velocity near the wall may help to explain the enhanced heat transfer of an RMDHL.

High Heat Flux Phase Change on Silicon Wick Structures

2012 ◽  
Author(s):  
Qingjun Cai ◽  
Avijit Bhunia ◽  
Yuan Zhao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Phase Change ◽  
Test Chamber ◽  
Nucleate Boiling ◽  
High Heat ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Wick Structure ◽  
Silicon Pillars

Silicon is the major material in IC manufacture. It has high thermal conductivity and is compatible with precision micro-fabrication. It also has decent thermal expansion coefficient to most semiconductor materials. These characteristics make it an ideally underlying material for fabricating micro/mini heat pipes and their wick structures. In this paper, we focus our research investigations on high heat flux phase change capacity of the silicon wick structures. The experimental wick sample is composed of silicon pillars 320μm in height and 30 ∼ 100μm in diameter. In a stainless steel test chamber, synchronized visualizations and measurements are performed to crosscheck experimental phenomena and data. Using the mono-wick structure with large silicon pillar of 100μm in diameter, the phase change on the silicon wick structure reaches its maximum heat flux at 1,130W/cm2 over a 2mm×2mm heating area. The wick structure can fully utilize the wick pump capability to supply liquid from all 360° directions to the center heating area. In contrast, the large heating area and fine silicon pillars 10μm in diameter significantly reduces liquid transport capability and suppresses generation of nucleate boiling. As a result, phase change completely relies on evaporation, and the CHF of the wick structure is reduced to 180W/cm2. An analytical model based on high heat flux phase change of mono-porous wick structures indicates that heat transfer capability is subjected to the ratio between the wick particle radius and the heater dimensions, as well as vapor occupation ratio of the porous volume. In contrast, phase change heat transfer coefficients of the wick structures essentially reflect material properties of wick structure and mechanism of two-phase interactions within wick structures.

Guidelines for Designing Micropillar Structures for Enhanced Evaporative Heat Transfer

2021 ◽  
Author(s):  
Kidus Guye ◽  
De Dong ◽  
Yunseo Kim ◽  
Hyoungsoon Lee ◽  
Baris Dogruoz ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Interfacial Area ◽  
High Heat ◽  
Heat Fluxes ◽  
Air Cooling ◽  
Transfer Coefficients ◽  
Two Phase ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Evaporation Heat

Abstract Over the last several decades, cooling technologies have been developed to address the growing thermal challenges associated with high-powered electronics. However, within the next several years, the heat generated by these devices is predicted to exceed 1 kW/cm2, and traditional methods, such as air cooling, are limited in their capacities to dissipate such high heat fluxes. In contrast, two-phase cooling methods, such as microdroplet evaporation, are very promising due to the large latent heat of vaporization associated with the phase change process. Previous studies have shown non-axisymmetric droplets exhibit different evaporation characteristics than spherical droplets. For a droplet pinned atop a micropillar, the solid-liquid and liquid-vapor interfacial area, the volume, and thickness of the droplet are the major factors that govern the evaporation heat transport process. In this work, we develop a shape optimization tool using the particle swarm optimization algorithm to maximize evaporation from a droplet confined atop a micropillar. The tool is used to optimize the shape of a nonaxisymmetric droplet. Compared to droplets atop circular and regular equilateral triangular micropillar structures, we find that droplets confined on pseudo-triangular micropillar structures have 23.7% and 5.7% higher heat transfer coefficients, respectively. The results of this work will advance the design of microstructures that support droplets with maximum heat transfer performance.

scholarly journals WEDM of Copper for the Fabrication of Large Surface-Area Micro-Channels: A Prerequisite for the High Heat-Transfer Rate

Micromachines ◽  
2020 ◽  
Vol 11 (2) ◽  
pp. 173 ◽  
Author(s):  
Naveed Ahmed ◽  
Mohammad Pervez Mughal ◽  
Waqar Shoaib ◽  
Syed Farhan Raza ◽  
Abdulrhman M. Alahmari
Keyword(s):  
Heat Transfer ◽  
Surface Area ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
High Heat ◽  
Critical Feature ◽  
Maximum Heat ◽  
High Heat Transfer ◽  
Maximum Heat Transfer ◽  
Micro Channels

To get the maximum heat transfer in real applications, the surface area of the micro-features (micro-channels) needs to be large as possible. It can be achieved by producing a maximum number of micro-channels per unit area. Since each successive pair of the micro-channels contain an inter-channels fin, therefore the inter-channels fin thickness (IFT) plays a pivotal role in determining the number of micro-channels to be produced in the given area. During machining, the fabrication of deep micro-channels is a challenge. Wire-cut electrical discharge machining (EDM) could be a viable alternative to fabricate deep micro-channels with thin inter-channels fins (higher aspect ratio) resulting in larger surface area. In this research, minimum IFT and the corresponding machining conditions have been sought for producing micro-channels in copper. The other attributes associated with the micro-channels have also been deeply investigated including the inter-channels fin height (IFH), inter-channels fin radius (IFR) and the micro-channels width (MCW). The results reveal that the inter-channels fin is the most critical feature to control during the wire electrical discharge machining (WEDM) of copper. Four types of fin shapes have been experienced, including the fins: broken at the top end, deflected at the top end, curled bend at the top, and straight with no/negligible deflection.

Experimental Investigation of a Flat-Plate Oscillating Heat Pipe With Modified Evaporator and Condenser

2014 ◽  
Author(s):  
M. J. Rhodes ◽  
M. R. Taylor ◽  
J. G. Monroe ◽  
S. M. Thompson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flat Plate ◽  
Thermal Performance ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Oscillating Heat Pipe ◽  
Lower Heat ◽  
Operating Temperatures

The thermal performance of a flat-plate oscillating heat pipe (FP-OHP) - with modified evaporator and condenser was experimentally investigated during high heat flux conditions. The copper FP-OHP (101.6 × 101.6 × 3.18 mm3) possessed two inter-connected layers of 1.02 mm2 square channels with the evaporator and condenser possessing two parallel, 0.25 × 0.51 mm2 square microchannels. The microchannels were integrated to enhance evaporation and condensation heat transfer to improve the FP-OHP’s ability to transport high heat flux. The FP-OHP was oriented vertically and locally heated with a 14.52 cm2 heating block at its base and cooled with a water block that provided either: 20 °C, 40 °C, or 60 °C operating temperatures. A FP-OHP without embedded microchannels was also investigated for baseline performance comparison. Both FP-OHPs were filled with Novec HFE-7200 (3M) working fluid at a filling ratio of approximately 80% by volume. The maximum temperature of each FP-OHP was recorded versus time for various heat inputs for the investigated operating temperatures. The results indicate that the integrated microchannels enhance the FP-OHP’s thermal performance for all operating temperatures. At 20 °C, 40 °C, and 60 °C, the microchannel-embedded evaporator and condenser dissipated 80 W, 65 W, and 55 W more than the baseline control with a minimum thermal resistance of 0.219 °C/W, 0.205 °C/W, and 0.170 °C/W, respectively — corresponding to a percent enhancement on-the-order of 25%. This percent enhancement increased with operating temperature. It has also been shown that Novec HFE-7200 allows the FP-OHP to start at relatively lower heat inputs — as low as 35 W, demonstrating that this working fluid can enhance heat transfer even at lower heat flux applications.

High Heat Flux Dissipation Using Symmetric Dual-Taper Manifold in Pool Boiling

2019 ◽  
Author(s):  
Aranya Chauhan ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pool Boiling ◽  
Heat Removal ◽  
Heating Surface ◽  
High Heat ◽  
Copper Surface ◽  
High Heat Flux ◽  
Maximum Heat ◽  
Continuous Increase

Abstract The trend of miniaturization in electronics presents a great challenge in the thermal management of devices. The continuous increase in the number of transistors in the processor leads to high heat flux generation, limiting the performance of the device. Boiling heat transfer offers a great heat removal competency while maintaining the low chip temperatures. The critical heat flux (CHF) dictates the maximum heat removal ability, and heat transfer coefficient (HTC) defines the efficiency of the boiling process. This pool boiling study is focused on using a manifold containing a symmetric dual taper over the heating surface. The heat transfer performance of this configuration is evaluated for different taper angles in the manifold. The macro-convection assisted by vapor columns during boiling enhance the CHF and HTC limit significantly. A CHF of 287 W/cm2 with an HTC of 116 kW/cm2°C was achieved with a plain copper surface, representing greater than a 2-fold increases in each over a plain surface.

Sign in / Sign up

Export Citation Format

Share Document