scholarly journals Impact Response of Hammerhead Pier Fibrous Concrete Beams Designed with Topology Optimization

2020 ◽  
Author(s):  
Meivazhisalai Parasuraman Salaimanimagudam ◽  
Covaty Ravi Suribabu ◽  
Gunasekaran Murali ◽  
Sallal R. Abid
Keyword(s):  
Topology Optimization ◽  
Concrete Beams ◽  
Impact Load ◽  
Impact Resistance ◽  
Adaptive Mesh ◽  
Impact Response ◽  
Adaptive Meshing ◽  
Repeated Impact ◽  
Ductility Ratio ◽  
The Impact

Reducing the weight of concrete beams is a primary (beyond strength and durability) concern of engineers. Therefore, this research was directed to investigate the impact response of hammerhead pier concrete beams designed with density-based method topology optimization. The finite element topology optimization was conducted using Autodesk fusion 360 considering three different mesh sizes of 7 mm, 10 mm, and adaptive meshing. Three optimized hammerhead beam configurations; HB1, HB2, and HB3, respectively, with volume reductions greater than 50 %. In the experimental part of this research, nine beams were cast with identical size and configuration to the optimized beams. Three beams, identical to the optimized beams, were tested under static bending for verification purposes. In comparison, six more beams, as in the preceding three beams but without and with hooked end steel fibers, were tested under repeated impact load. The test results revealed that the highest flexural capacity and impact resistance at crack initiation and failure were recorded for the adaptive mesh beams (HB3 and HB3SF). The failure impact energy and ductility ratio of the beam HB3SF was higher than the beams HB1SF and HB2SF by more than 270 %. The results showed that the inclusion of steel fiber duplicated the optimized beam’s impact strength and ductility several times. The failure impact resistance of fibrous beams was higher than their corresponding plain beams by approximately 2300 to4460 %, while their impact ductility ratios were higher by 6.0 to 18.1 times.

scholarly journals Residual Impact Performance of ECC Subjected to Sub-High Temperatures

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 454
Author(s):  
Raad A. Al-Ameri ◽  
Sallal Rashid Abid ◽  
Gunasekaran Murali ◽  
Sajjad H. Ali ◽  
Mustafa Özakça ◽  
...  
Keyword(s):  
High Temperatures ◽  
Reference Group ◽  
Impact Resistance ◽  
Impact Response ◽  
Repeated Impact ◽  
Impact Performance ◽  
Compressive And Flexural Strengths ◽  
Reference Specimens ◽  
Temperature Exposure ◽  
The Impact

Despite the fact that the mechanical properties of Engineered Cementitious Composites (ECC) after high-temperature exposure are well investigated in the literature, the repeated impact response of ECC is not yet explored. Aiming to evaluate the residual impact response of ECC subjected to sub-high temperatures under repeated drop weight blows, the ACI 544-2R repeated impact test was utilized in this study. Disk impact specimens (150 mm diameter and 64 mm thickness) were prepared from the M45 ECC mixture but using polypropylene fibers, while similar 100 mm cube specimens and 100 × 100 × 400 mm prism specimens were used to evaluate the compressive and flexural strengths. The specimens were all cast, cured, heated, cooled, and tested under the same conditions and at the same age. The specimens were subjected to three temperatures of 100, 200 and 300 °C, while a group of specimens was tested without heating as a reference group. The test results showed that heating to 100 and 200 °C did not affect the impact resistance noticeably, where the retained cracking and failure impact numbers and ductility were higher or slightly lower than those of unheated specimens. On the other hand, exposure to 300 °C led to a serious deterioration in the impact resistance and ductility. The retained failure impact numbers after exposure to 100, 200, and 300 °C were 313, 257, and 45, respectively, while that of the reference specimens was 259. The results also revealed that the impact resistance at this range of temperature showed a degree of dependency on the compressive strength behavior with temperature.

Exact impact response of multi-layered cement-based piezoelectric composite considering electrode effect

2018 ◽  
Vol 30 (3) ◽  
pp. 400-415 ◽  
Author(s):  
Taotao Zhang ◽  
Keping Zhang ◽  
Wende Liu
Keyword(s):  
Analytical Method ◽  
Virtual Work ◽  
Impact Load ◽  
Summation Method ◽  
Impact Response ◽  
Piezoelectric Composite ◽  
Smart Devices ◽  
Natural Modes ◽  
The Impact ◽  
The Mathematical Model

Multi-layered cement-based piezoelectric composites could enable accurate real-time detection of the concrete structure deformation induced by impact load. An analytical method for quantifying the impact response of the multi-layered cement-based piezoelectric composite is established based on the piezo-elasticity, and a general transfer matrix description for the composite with any number of layers is derived. The motion of the composite is decomposed into natural modes according to its physical significance of vibration modes. The mechanical and electrical solutions are obtained via the mode summation method and the virtual work principle. In order to give a clear demonstration, some numerical simulations are conducted to verify the validity of the theoretical analysis. Moreover, the current analytical method considers the electrode as an extra layer and evaluates the effect of its thickness and material on the performance of the multi-layered cement-based piezoelectric composite. It can be seen that the mathematical model presented in this article provides a rigorous tool for the analysis of the multi-layered cement-based piezoelectric composite and therefore could benefit the design of certain types of smart devices under impact load.

scholarly journals Impact Resistance Analysis and Optimization of Variant Truss Beam Structure Based on Material Properties

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5847
Author(s):  
Xiaohao Li ◽  
Junqi Pan ◽  
Xingchen Zhou
Keyword(s):  
Simulation Analysis ◽  
Impact Load ◽  
Impact Resistance ◽  
Structure Design ◽  
Response Surfaces ◽  
Optimization Strategy ◽  
Buffer Effect ◽  
Characteristic Analysis ◽  
Beam Structure ◽  
The Impact

In order to meet the increasing application requirements with regards to structural impact resistance in industries such as mining, construction, aerospace engineering, and disaster relief and mitigation, this paper designs a variant truss beam structure with a large shrinkage ratio and high impact resistance. Based on the principle of the curved trajectory of scissor mechanisms, this paper conducts a finite element simulation analysis of the impact load on the truss beam structure, a theoretical analysis of the impact response and a relevant prototype bench-top experiment, completing a full study on the impact resistance mechanism of the designed variant truss beam structure under the impact load. In the paper, the buffer effect of the external load impact on the variant truss beam structure is analyzed from the perspective of the energy change of elastic–plastic deformation. This paper proposes an optimization strategy for the variant truss beam structure with the energy absorption rate as the optimization index through extensive analysis of the parameter response surfaces. The strategy integrates analyses on the response characteristic analysis of various configuration materials to obtain an optimal combination of component parameters that ensures that the strength of the truss beam structure meets set requirements. The strategy provides a feasible method with which to verify the effectiveness and impact resistance of a variant truss structure design.

scholarly journals Experimental investigation of the impact response of novel steelbiocomposite hybrid materials

2018 ◽  
Vol 183 ◽  
pp. 02040
Author(s):  
KarthikRam Ramakrishnan ◽  
Mikko Hokka ◽  
Essi Sarlin ◽  
Mikko Kanerva ◽  
Reijo Kouhia ◽  
...  
Keyword(s):  
High Speed ◽  
Structural Integrity ◽  
Metal Layer ◽  
Rear Surface ◽  
Impact Resistance ◽  
Natural Fibre ◽  
Image Correlation ◽  
Impact Response ◽  
High Speed Camera ◽  
The Impact

Recent developments in the production of technical flax fabrics allow the use of sustainable natural fibres to replace synthetic fibres in the manufacture of structural composite parts. Natural fibre reinforced biocomposites have been proven to satisfy design and structural integrity requirements but impact strength has been identified as one of their limitations. In this paper, hybridisation of the biocomposite with a metal layer has been investigated as a potential method to improve the impact resistance of natural fibre composites. The impact response of biocomposites made of flax-epoxy is investigated experimentally using a high velocity particle impactor. A high-speed camera setup was used to observe the rear surface of the plates during impact. Digital Image Correlation (DIC) of the high speed camera images was used for full-field strain measurement and to study the initiation and propagation of damage during the impact. The different modes of damage in the hybrid laminate were identified by postimpact analysis of the section of the damaged composite plate using optical microscopy. The study shows the difference in impact response for different material combinations and configurations. The hybrid construction was shown to improve the impact resistance of the flax composite.

scholarly journals Axial Impact Load of a Concrete-Filled Steel Tubular Member with Axial Compression Considering the Creep Effect

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3134 ◽  
Author(s):  
Tao Lan ◽  
Guangchong Qin ◽  
Jinzhao Zhuang ◽  
Youdi Wang ◽  
Qian Zheng ◽  
...  
Keyword(s):  
Impact Load ◽  
Slenderness Ratio ◽  
Concrete Strength ◽  
Pressure Ratio ◽  
Impact Resistance ◽  
Axial Pressure ◽  
Axial Impact ◽  
Creep Effect ◽  
The Impact ◽  
Peak Value

The dynamic loads acting on concrete-filled steel tubular members under axial impacts by rigid bodies were studied herein by FEM. The whole impact process was simulated and the time history of the impact load was obtained. The effects of eight factors on the axial impact load were studied; these factors were the impact speed, mass ratio, axial pressure ratio, steel ratio, slenderness ratio, concrete strength, impact position, and boundary conditions. Besides this, the effects of concrete creep on the impact load were also considered by changing the material parameters of the concrete. The results show that axial impact load changes with time as a triangle. The peak value of impact load increases and the impact resistance improves with the growth of the axial pressure ratio, steel ratio, slenderness ratio, and concrete strength after creep occurs. As the eccentricity of the axial impact acting on a concrete-filled steel tubular member increases, the peak value of the impact load decreases. The enhancement of constraints at both ends of the member can improve the impact resistance. The creep reduction coefficients for the peak axial impact load of a concrete-filled steel tubular member under axial compression and considering the creep effect over 6 months and 30 years are 0.60 and 0.55, respectively. A calculation formula for the peak value of impact load was suggested based on the existing formula, and its accuracy was proved by finite element calculation in this study.

Effect of cracking localization on the structural ductility of normal strength and high strength reinforced concrete beams with steel fibers

2019 ◽  
Vol 10 (4) ◽  
pp. 457-469 ◽  
Author(s):  
Avraham N Dancygier ◽  
Yuri S Karinski
Keyword(s):  
Reinforced Concrete ◽  
Transition Point ◽  
Concrete Beams ◽  
High Strength ◽  
Reinforcement Ratio ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Flexural Ductility ◽  
Ductility Ratio ◽  
The Impact

This article presents a study of cracking localization in normal and high strength concrete beams that include steel fibers and the influence of this localization on their structural ductility. It is shown that for a given fiber type and content, as the reinforcement ratio ρ decreases, the cracking localization level increases. The effect of ρ on the level of cracking localization is more pronounced for low amounts of conventional reinforcement. This range of conventional reinforcement ratio is typical of slabs and especially for the commonly thicker protective slabs. Examination of the effect of the reinforcement ratio on the flexural ductility shows that there exists a transition point below which the ductility ratio decreases with  ρ. This transition point is well above the minimum reinforcement ratio, which is required in design codes for plain reinforced concrete elements. Empirical analysis of the relation between cracking localization and ductility ratio shows that up to the same transition point, as cracking localization increases, the flexural ductility decreases. Findings of this study show that the positive effect of adding fibers on enhancing the impact resistance of slabs and beams is conflicted by their negative influence on reducing the structural ductility for low reinforcement ratios, which are typical of protective slabs.

scholarly journals Experimental Investigation on Relations Between Impact Resistance and Tensile Properties of Cement-Based Materials Reinforced by Polyvinyl Alcohol Fibers

2019 ◽  
Vol 9 (20) ◽  
pp. 4434
Author(s):  
Ju Zhang ◽  
Pucun Bai ◽  
Changwang Yan ◽  
Shuguang Liu ◽  
Xiaoxiao Wang
Keyword(s):  
Polyvinyl Alcohol ◽  
Tensile Properties ◽  
Impact Load ◽  
Impact Resistance ◽  
Crater Diameter ◽  
Cement Based Materials ◽  
Weight Test ◽  
Ultimate Failure ◽  
Drop Weight Test ◽  
The Impact

Cement-based material is brittle and is easily damaged by an impact load with a few blows. The purpose of this paper is to study the relations between the impact resistance and tensile properties of cement-based materials reinforced by polyvinyl alcohol fiber (PVA-FRCM). A drop-weight test and uniaxial tension test were performed. The relations were studied based on the experimental results, including the relation between the blow number and the tensile stress at the first visible cracking (σc) and the relation between the blow number and the tensile strain at the ultimate failure (εf). Results showed that the blow number for the first visible crack for disc impact specimens increases obviously with the increase of σc of slab specimens. The crater diameter and blow number for ultimate failure of the disc specimens increase with the increase of εf of slab specimens. For the PVA-FRCM specimens with larger σc and εf, much more blows are needed to cause both the first visible crack and ultimate failure. Polyvinyl alcohol fibers can reinforce impact resistance and tensile properties of cement-based materials.

scholarly journals Performance based design of reinforced concrete beams under impact

2010 ◽  
Vol 10 (6) ◽  
pp. 1069-1078 ◽  
Author(s):  
S. Tachibana ◽  
H. Masuya ◽  
S. Nakamura
Keyword(s):  
Reinforced Concrete ◽  
Collision Energy ◽  
Concrete Beams ◽  
Impact Load ◽  
Experimental Results ◽  
Reinforced Concrete Beams ◽  
Performance Based Design ◽  
Impact Action ◽  
The Impact ◽  
A Performance

Abstract. The purpose of this research is to collect fundamental data and to establish a performance-based design method for reinforced concrete beams under perpendicular impact load. Series of low speed impact experiments using reinforced concrete beams were performed varying span length, cross section and main reinforcement. The experimental results are evaluated focusing on the impact load characteristics and the impact behaviours of reinforced concrete beams. Various characteristic values and their relationships are investigated such as the collision energy, the impact force duration, the energy absorbed by the beams and the beam response values. Also the bending performance of the reinforced concrete beams against perpendicular impact is evaluated. An equation is proposed to estimate the maximum displacement of the beam based on the collision energy and the static ultimate bending strength. The validity of the proposed equation is confirmed by comparison with experimental results obtained by other researchers as well as numerical results obtained by FEM simulations. The proposed equation allows for a performance based design of the structure accounting for the actual deformation due to the expected impact action.

Impact resistance of Nomex honeycomb sandwich structures with thin fibre reinforced polymer facesheets

2016 ◽  
Vol 20 (5) ◽  
pp. 531-552 ◽  
Author(s):  
Longquan Liu ◽  
Han Feng ◽  
Huaqing Tang ◽  
Zhongwei Guan
Keyword(s):  
Finite Element ◽  
Impact Energy ◽  
Sandwich Structures ◽  
Impact Resistance ◽  
Impact Response ◽  
Woven Fabric ◽  
Drop Weight ◽  
Honeycomb Sandwich ◽  
Nomex Honeycomb ◽  
The Impact

In order to investigate the impact resistance of the Nomex honeycomb sandwich structures skinned with thin fibre reinforced woven fabric composites, both drop-weight experimental work and meso-mechanical finite element modelling were conducted and the corresponding output was compared. Drop-weight impact tests with different impact parameters, including impact energy, impactor mass and facesheets, were carried out on Nomex honeycomb-cored sandwich structures. It was found that the impact resistance and the penetration depth of the Nomex honeycomb sandwich structures were significantly influenced by the impact energy. However, for impact energies that cause full perforation, the impact resistance is characterized with almost the same initial stiffness and peak force. The impactor mass has little influence on the impact response and the perforation force is primarily dependent on the thickness of the facesheet, which generally varies linearly with it. In the numerical simulation, a comprehensive finite element model was developed which considers all the constituent materials of the Nomex honeycomb, i.e. aramid paper, phenolic resin, and the micro-structure of the honeycomb wall. The model was validated against the corresponding experimental results and then further applied to study the effects of various impact angles on the response of the honeycomb. It was found that both the impact resistance and the perforation depth are significantly influenced by the impact angle. The former increases with the obliquity, while the latter decreases with it. The orientation of the Nomex core has little effect on the impact response, while the angle between the impact direction and the fibre direction of the facesheets has a great influence on the impact response.

Influence of Crumb Rubber on Impact Energy of Steel Fiber Concrete Beams

2015 ◽  
Vol 802 ◽  
pp. 196-201
Author(s):  
Ahmed Tareq Noaman ◽  
Badorul Hisham Abu Bakar ◽  
Hazizan Md. Akil
Keyword(s):  
Impact Energy ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Impact Load ◽  
Crumb Rubber ◽  
Fine Aggregate ◽  
Low Velocity ◽  
Fiber Concrete ◽  
Steel Fiber Concrete ◽  
The Impact

This paper presents the impact energy of steel fiber concrete beams at first crack and failure with different replacement ratios of crumb rubber. The test was carried out using simple low velocity drop weight test rig for both normal concrete (NC) and steel fiber concrete (SFC). The crumb rubber with particle size of 1 – 2 mm was added with replacement ratios of 5%, 15%, and 25% by volume of fine aggregate. Six batches consisting of 6 beams (100x100x500 mm) containing 0.5% of hooked end steel fibers were tested under impact load in accordance with ACI Committee 544. The specimens were tested at the age 90 days after curing in water. The results show a reduction in the compressive strength for both NC and SFC with the incorporation of crumb rubber with greater reduction at higher crumb rubber content. However, the measured impact energy for both NC and SFC was foundincreasing with the crumb rubber replacement.

Sign in / Sign up

Export Citation Format

Share Document