scholarly journals Experimental investigation of the impact response of novel steelbiocomposite hybrid materials

2018 ◽  
Vol 183 ◽  
pp. 02040
Author(s):  
KarthikRam Ramakrishnan ◽  
Mikko Hokka ◽  
Essi Sarlin ◽  
Mikko Kanerva ◽  
Reijo Kouhia ◽  
...  
Keyword(s):  
High Speed ◽  
Structural Integrity ◽  
Metal Layer ◽  
Rear Surface ◽  
Impact Resistance ◽  
Natural Fibre ◽  
Image Correlation ◽  
Impact Response ◽  
High Speed Camera ◽  
The Impact

Recent developments in the production of technical flax fabrics allow the use of sustainable natural fibres to replace synthetic fibres in the manufacture of structural composite parts. Natural fibre reinforced biocomposites have been proven to satisfy design and structural integrity requirements but impact strength has been identified as one of their limitations. In this paper, hybridisation of the biocomposite with a metal layer has been investigated as a potential method to improve the impact resistance of natural fibre composites. The impact response of biocomposites made of flax-epoxy is investigated experimentally using a high velocity particle impactor. A high-speed camera setup was used to observe the rear surface of the plates during impact. Digital Image Correlation (DIC) of the high speed camera images was used for full-field strain measurement and to study the initiation and propagation of damage during the impact. The different modes of damage in the hybrid laminate were identified by postimpact analysis of the section of the damaged composite plate using optical microscopy. The study shows the difference in impact response for different material combinations and configurations. The hybrid construction was shown to improve the impact resistance of the flax composite.

Measurement of Transient Dynamic Response of Circuit Boards of a Handheld Device During Drop Using 3D Digital Image Correlation

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
S. B. Park ◽  
Chirag Shah ◽  
Jae B. Kwak ◽  
Changsoo Jang ◽  
Soonwan Chung ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
High Speed ◽  
Image Correlation ◽  
Impact Response ◽  
Experimental Methodology ◽  
Full Field ◽  
Handheld Device ◽  
3D Digital Image Correlation ◽  
The Impact

In this work, a new experimental methodology for analyzing the drop impact response is assessed using a pair of high-speed digital cameras and 3D digital image correlation software. Two different test boards are subjected to Joint Electron Device Engineering Council (JEDEC) standard free-fall impact conditions of half-sine pulse of 1500 G in magnitude and 0.5 ms in duration. The drop is monitored using a pair of synchronized high-speed cameras at a rate of up to 15,000 frames per second. The acquired images are subsequently analyzed to give full-field dynamic deformation, shape, and strain over the entire board during and after impact. To validate this new methodology for analyzing the impact response, the in-plane strain as well as the out-of-plane acceleration at selected locations were measured simultaneously during the drop using strain gauge and accelerometers and were compared with those obtained using high-speed cameras and 3D digital image correlation presented in this paper. Comparison reveals excellent correlation of the transient behavior of the board during impact and confirms the feasibility of using the full-field measurement technique used in this study.

scholarly journals The comparison of projectile impact resistance of ultra-high-performance fibre-reinforced concrete with various aggregates

2021 ◽  
Vol 250 ◽  
pp. 06007
Author(s):  
Martina Drdlová ◽  
Martin Šperl
Keyword(s):  
Reinforced Concrete ◽  
High Speed ◽  
High Performance ◽  
Structural Integrity ◽  
Impact Load ◽  
Impact Resistance ◽  
Fibre Reinforced Concrete ◽  
Projectile Impact ◽  
The Impact ◽  
High Performance Fibre

In order to apply the ultra-high-performance fibre-reinforced concrete (UHPFRC) in the constructions of ballistic protective structures, the impact resistance of UHPFRC has been investigated experimentally by conducting the high-speed projectile penetration tests. 5 mixtures with basalt and corundum aggregates with various grain size have been prepared and subjected to the quasi-static and 7.62 x 54R B32 API projectile impact load using the striking velocity of 850 m/s. The influence of the strength, size and material of the aggregate on the projectile impact resistance represented by differential efficiency factor (DEF), structural integrity and area and height of impact crater has been evaluated. The superior projectile resistance of UHPFRC with corundum has been observed. Regarding the size of the aggregates, the incorporation of coarser aggregates brings better projectile impact resistance.

scholarly journals Full-Field Operational Modal Analysis of an Aircraft Composite Panel from the Dynamic Response in Multi-Impact Test

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1602
Author(s):  
Ángel Molina-Viedma ◽  
Elías López-Alba ◽  
Luis Felipe-Sesé ◽  
Francisco Díaz
Keyword(s):  
Modal Analysis ◽  
Energy Absorption ◽  
High Speed ◽  
Operational Modal Analysis ◽  
Modal Identification ◽  
Image Correlation ◽  
Composite Panel ◽  
Impact Excitation ◽  
Full Field ◽  
The Impact

Experimental characterization and validation of skin components in aircraft entails multiple evaluations (structural, aerodynamic, acoustic, etc.) and expensive campaigns. They require different rigs and equipment to perform the necessary tests. Two of the main dynamic characterizations include the energy absorption under impact forcing and the identification of modal parameters through the vibration response under any broadband excitation, which also includes impacts. This work exploits the response of a stiffened aircraft composite panel submitted to a multi-impact excitation, which is intended for impact and energy absorption analysis. Based on the high stiffness of composite materials, the study worked under the assumption that the global response to the multi-impact excitation is linear with small strains, neglecting the nonlinear behavior produced by local damage generation. Then, modal identification could be performed. The vibration after the impact was measured by high-speed 3D digital image correlation and employed for full-field operational modal analysis. Multiple modes were characterized in a wide spectrum, exploiting the advantages of the full-field noninvasive techniques. These results described a consistent modal behavior of the panel along with good indicators of mode separation given by the auto modal assurance criterion (Auto-MAC). Hence, it illustrates the possibility of performing these dynamic characterizations in a single test, offering additional information while reducing time and investment during the validation of these structures.

scholarly journals Impact Response of Hammerhead Pier Fibrous Concrete Beams Designed with Topology Optimization

2020 ◽  
Author(s):  
Meivazhisalai Parasuraman Salaimanimagudam ◽  
Covaty Ravi Suribabu ◽  
Gunasekaran Murali ◽  
Sallal R. Abid
Keyword(s):  
Topology Optimization ◽  
Concrete Beams ◽  
Impact Load ◽  
Impact Resistance ◽  
Adaptive Mesh ◽  
Impact Response ◽  
Adaptive Meshing ◽  
Repeated Impact ◽  
Ductility Ratio ◽  
The Impact

Reducing the weight of concrete beams is a primary (beyond strength and durability) concern of engineers. Therefore, this research was directed to investigate the impact response of hammerhead pier concrete beams designed with density-based method topology optimization. The finite element topology optimization was conducted using Autodesk fusion 360 considering three different mesh sizes of 7 mm, 10 mm, and adaptive meshing. Three optimized hammerhead beam configurations; HB1, HB2, and HB3, respectively, with volume reductions greater than 50 %. In the experimental part of this research, nine beams were cast with identical size and configuration to the optimized beams. Three beams, identical to the optimized beams, were tested under static bending for verification purposes. In comparison, six more beams, as in the preceding three beams but without and with hooked end steel fibers, were tested under repeated impact load. The test results revealed that the highest flexural capacity and impact resistance at crack initiation and failure were recorded for the adaptive mesh beams (HB3 and HB3SF). The failure impact energy and ductility ratio of the beam HB3SF was higher than the beams HB1SF and HB2SF by more than 270 %. The results showed that the inclusion of steel fiber duplicated the optimized beam’s impact strength and ductility several times. The failure impact resistance of fibrous beams was higher than their corresponding plain beams by approximately 2300 to4460 %, while their impact ductility ratios were higher by 6.0 to 18.1 times.

Dynamic Analysis of Thin Glass Under Ball Drop Impact With New Metrics

2013 ◽  
Author(s):  
Liang Xue ◽  
Claire R. Coble ◽  
Hohyung Lee ◽  
Da Yu ◽  
Satish Chaparala ◽  
...  
Keyword(s):  
High Speed ◽  
Impact Testing ◽  
Image Correlation ◽  
Thin Glass ◽  
Fea Model ◽  
Wear And Tear ◽  
Local Measurements ◽  
Drop Impacts ◽  
Global And Local ◽  
The Impact

Response of brittle plate to impact loads has been the subject of many research studies [1–7]. Specifically, glass presents a wide variety of applications in daily life, and helps to protect the displays of smartphones, tablets, PCs, and TVs from everyday wear and tear. Therefore, the necessity of glass to resist scratches, drop impacts, and bumps from everyday use leads to the importance of investigation of the glass response under dynamic impact loading. The ball drop test has been applied in the past, specifying an energy threshold as a prediction metric. Use of energy as the key parameter in impact testing is limited, since it does not account for the time spent in contact during the impact event. This study attempts to establish a reliable metric for impact testing based on a momentum change threshold. The deformation and the strain of the glass will be obtained by the Digital Image Correlation (DIC) system, while the rebound velocity will be measured with the high speed cameras. The global and local measurements are conducted to verify the accuracy of the experimental results. Finally, the FEA model is developed using ANSYS/LS-DYNA to provide a comprehensive understanding of the dynamic response of the glass. Excellent correlation in deflection is obtained between the measurements and predictions.

scholarly journals Dynamic damage in carbon-fibre composites

2016 ◽  
Vol 374 (2071) ◽  
pp. 20160018 ◽  
Author(s):  
N. K. Bourne ◽  
S. Parry ◽  
D. Townsend ◽  
P. J. Withers ◽  
C. Soutis ◽  
...  
Keyword(s):  
Carbon Fibre ◽  
High Speed ◽  
Failure Modes ◽  
Structural Integrity ◽  
High Speed Photography ◽  
Compression Phase ◽  
Impact Surface ◽  
Fibre Composites ◽  
The Impact ◽  
Carbon Fibre Composites

The Taylor test is used to determine damage evolution in carbon-fibre composites across a range of strain rates. The hierarchy of damage across the scales is key in determining the suite of operating mechanisms and high-speed diagnostics are used to determine states during dynamic loading. Experiments record the test response as a function of the orientation of the cylinder cut from the engineered multi-ply composite with high-speed photography and post-mortem target examination. The ensuing damage occurs during the shock compression phase but three other tensile loading modes operate during the test and these are explored. Experiment has shown that ply orientations respond to two components of release; longitudinal and radial as well as the hoop stresses generated in inelastic flow at the impact surface. The test is a discriminant not only of damage thresholds but of local failure modes and their kinetics. This article is part of the themed issue ‘Multiscale modelling of the structural integrity of composite materials’.

High and Low Speed Impact Characteristics of Nanocomposites

2015 ◽  
Vol 1105 ◽  
pp. 62-66 ◽  
Author(s):  
Saud Aldajah ◽  
Yousef Haik ◽  
Kamal Moustafa ◽  
Ammar Alomari
Keyword(s):  
High Speed ◽  
Impact Resistance ◽  
Absorption Capacity ◽  
Impact Testing ◽  
Energy Absorption Capacity ◽  
Low Speed ◽  
High Speed Impact ◽  
Bulletproof Vest ◽  
Impact Characteristics ◽  
The Impact

Nanocomposites attracted the attention of scientists due to their superior mechanical, thermal, chemical and electrical properties. This research studied the impact of adding carbon nanotubes (CNTs) to the woven Kevlar laminated composites on the high and low speed impact characteristics. Different percentages of CNTs were added to the woven Kevlar-Vinylester composite materials. An in-house developed drop weight testing apparatus was utilized for the low speed impact testing. Two different concentrations of the CNTs were added to a 15-layer woven Kevlar laminates, 0.32 wt% and 0.8 wt%. The results showed that: The 0.32 wt % CNT sample enhanced the interlaminar strength of the composite without enhancing the energy absorption capacity whereas, the 0.8 wt % CNT sample did not improve the impact resistance of the Kevlar composite.For the high speed impact tests, a bulletproof vest was prepared using woven Kevlar, resin, and CNTs at 1.5 w% percentage. The ballistic shooting was carried out by a professional shooter using a 30 caliber and 9 mm bullets for the tests. The CNT bulletproof sample bounced back the 30 caliber copper alloy bullet with no penetration.

Impact resistance of Nomex honeycomb sandwich structures with thin fibre reinforced polymer facesheets

2016 ◽  
Vol 20 (5) ◽  
pp. 531-552 ◽  
Author(s):  
Longquan Liu ◽  
Han Feng ◽  
Huaqing Tang ◽  
Zhongwei Guan
Keyword(s):  
Finite Element ◽  
Impact Energy ◽  
Sandwich Structures ◽  
Impact Resistance ◽  
Impact Response ◽  
Woven Fabric ◽  
Drop Weight ◽  
Honeycomb Sandwich ◽  
Nomex Honeycomb ◽  
The Impact

In order to investigate the impact resistance of the Nomex honeycomb sandwich structures skinned with thin fibre reinforced woven fabric composites, both drop-weight experimental work and meso-mechanical finite element modelling were conducted and the corresponding output was compared. Drop-weight impact tests with different impact parameters, including impact energy, impactor mass and facesheets, were carried out on Nomex honeycomb-cored sandwich structures. It was found that the impact resistance and the penetration depth of the Nomex honeycomb sandwich structures were significantly influenced by the impact energy. However, for impact energies that cause full perforation, the impact resistance is characterized with almost the same initial stiffness and peak force. The impactor mass has little influence on the impact response and the perforation force is primarily dependent on the thickness of the facesheet, which generally varies linearly with it. In the numerical simulation, a comprehensive finite element model was developed which considers all the constituent materials of the Nomex honeycomb, i.e. aramid paper, phenolic resin, and the micro-structure of the honeycomb wall. The model was validated against the corresponding experimental results and then further applied to study the effects of various impact angles on the response of the honeycomb. It was found that both the impact resistance and the perforation depth are significantly influenced by the impact angle. The former increases with the obliquity, while the latter decreases with it. The orientation of the Nomex core has little effect on the impact response, while the angle between the impact direction and the fibre direction of the facesheets has a great influence on the impact response.

Sign in / Sign up

Export Citation Format

Share Document