scholarly journals Interaction of rock-bolt supports while weak rock reinforcing by means of injection rock bolts

2021 ◽  
Vol 15 (4) ◽  
pp. 8-14
Author(s):  
Oleksandr Krykovskyi ◽  
Viktoriia Krykovska ◽  
Serhii Skipochka
Keyword(s):  
Rock Mass ◽  
Mine Working ◽  
Initial Permeability ◽  
Rock Bolt ◽  
Water Inflow ◽  
Mechanics Of Solids ◽  
Gas Emission ◽  
Rock Bolts ◽  
A Value ◽  
Enclosing Rocks

Purpose is to analyze changes in shape and dimensions of a rock mass area, fortified with the help of a polymer, depending upon the density of injection rock bolts as well as the value of initial permeability of enclosing rocks to substantiate optimum process solutions to support roofs within the unstable rocks and protect mine workings against water inflow and gas emission. Methods. Numerical modeling method for coupled processes of rock mass strain and filtration of liquid components of a polymer has been applied. The model is based upon fundamental ideas of mechanics of solids and filtration theory. The problem has been solved using a finite element method. Its solution took into consideration both the initial permeability and the permeability stipulated by mine working driving, injection time of reagents and their polymerization, and effect of po-lymer foaming in the process of mixing of its components. Changes in physicomechanical and filtration characteristics of rock mass during polymer hardening were simulated. It has been taken into consideration that a metal delivery pipe starts operating as a reinforcing support element only after the polymer hardening. Findings. If three and five injection rock bolts are installed within a mine working section then stresses, permeability coefficients, pressure of liquid polymeric composition, and geometry of the fortified area of rock mass have been calculated. It has been shown that rock bolt location is quite important to form a rock-bolt arch. It has been demonstrated for the assumed conditions that if five injection rock bolts are installed within the mine working roof then close interaction between rock-bolt supports takes place; moreover, the integral arch is formed within the mine working roof. Originality. Dependence of change in the polymer reinforced area upon a value of initial permeability of enclosing rocks has been derived. It has been shown that in terms of low values of initial permeability, geometry of rock-bolt supports as well as its size is identified only by means of a value of the unloaded zone around the mine working. In this context, initial permeabi-lity increase results in the enlarged diameter of the reinforced rock mass area in the neighbourhood of the injection rock bolt. Practical implications. The findings are recommended to be applied while improving a method to support the mine working roof and decrease water inflow as well as gas emission from the rocks, being undermined, into the working.

scholarly journals Reinforcement of Underground Excavation with Expansion Shell Rock Bolt Equipped with Deformable Component

2017 ◽  
Vol 39 (1) ◽  
pp. 39-52 ◽  
Author(s):  
Waldemar Korzeniowski ◽  
Krzysztof Skrzypkowski ◽  
Krzysztof Zagórski
Keyword(s):  
Rock Mass ◽  
Construction Materials ◽  
Rock Bolt ◽  
Loading Test ◽  
Rock Bolts ◽  
Disk Spring ◽  
Static Loading Test ◽  
Two Phases ◽  
Rock Bolt Support ◽  
Ultimate Loading Capacity

AbstractThe basic type of rock mass reinforcement method for both preparatory and operational workings in underground metal ore mines, both in Poland and in different countries across the world, is the expansion shell or adhesive-bonded rock bolt. The article discusses results of static loading test of the expansion shell rock bolts equipped with originally developed deformable component. This component consists of two profiled rock bolt washers, two disk springs, and three guide bars. The disk spring and disk washer material differs in stiffness. The construction materials ensure that at first the springs under loading are partially compressed, and then the rock bolt washer is plastically deformed. The rock bolts tested were installed in blocks simulating a rock mass with rock compressive strength of 80 MPa. The rock bolt was loaded statically until its ultimate loading capacity was exceeded. The study presents the results obtained under laboratory conditions in the test rig allowing testing of the rock bolts at their natural size, as used in underground metal ore mines. The stress-strain/displacement characteristics of the expansion shell rock bolt with the deformable component were determined experimentally. The relationships between the geometric parameters and specific strains or displacements of the bolt rod were described, and the percentage contribution of those values in total displacements, resulting from the deformation of rock bolt support components (washer, thread) and the expansion shell head displacements, were estimated. The stiffness of the yielded and stiff bolts was empirically determined, including stiffness parameters of every individual part (deformable component, steel rod). There were two phases of displacement observed during the static tension of the rock bolt which differed in their intensity.

Laboratory Method for Evaluating the Characteristics of Expansion Rock Bolts Subjected to Axial Tension / Laboratoryjna Metoda Badania Charakterystyk Kotew Rozprężnych Poddanych Rozciąganiu Osiowemu

2015 ◽  
Vol 60 (1) ◽  
pp. 209-224 ◽  
Author(s):  
Waldemar Korzeniowski ◽  
Krzysztof Skrzypkowski ◽  
Łukasz Herezy
Keyword(s):  
Rock Mass ◽  
Laboratory Method ◽  
Operating Conditions ◽  
Rock Bolt ◽  
Test Facility ◽  
Geometrical Parameters ◽  
Rock Bolts ◽  
Axial Tension ◽  
Rock Bolt Support ◽  
Bolt Support

Abstract Rock bolts have long been used in Poland, above all in the ore mining. Worldwide experience (Australia, Chile, Canada, South Africa, Sweden, and USA) provides evidence of rock bolt supports being used for loads under both static and dynamic conditions. There are new construction designs dedicated to the more extreme operating conditions, particularly in mining but also in tunneling. Appreciating the role and significance of the rock bolt support and its use in Polish conditions amounting to millions of units per year, this article describes a new laboratory test facility which enables rock bolt testing under static load conditions. Measuring equipment used as well as the possibilities of the test facility were characterized. Tests were conducted on expansion rock bolt supports installed inside a block simulating rock mass with compression strength of 80 MPa, which was loaded statically as determined by taking account of the load in order to maintain the desired axial tension, which was statically burdened in accordance with determined program load taking into consideration the maintenance of set axial tension strength at specified time intervals until capacity was exceeded. As an experiment the stress-strain characteristics of the rock bolt support were removed showing detailed dependence between its geometrical parameters as well as actual rock bolt deformation and its percentage share in total displacement and deformation resulting from the deformation of the bolt support elements (washer, thread). Two characteristic exchange parts with varying intensity of deformation /displacement per unit were highlighted with an increase in axial force static rock bolt supports installed in the rock mass.

scholarly journals Mathematical modeling of tight roof periodical falling

2018 ◽  
Vol 60 ◽  
pp. 00020 ◽  
Author(s):  
Vira Prykhodko ◽  
Nataliia Ulanova ◽  
Oleksandr Haidai ◽  
Dina Klymenko
Keyword(s):  
Mathematical Modeling ◽  
Rock Mass ◽  
Boundary Element Method ◽  
Coal Seam ◽  
Mine Working ◽  
Strain State ◽  
Stress And Strain ◽  
Mine Workings ◽  
Roof Falling ◽  
Enclosing Rocks

The paper proposes a method to determine of a coal seam roof falling step basing upon the analysis of stress and strain state of the rock mass area with mine workings formed as a result of coal preparatory and extraction operations. A boundary element method has been applied to define stress and strain state (SSS). Fissuring of enclosing rocks was modeled by means of transversal-isotropic medium. Dependence of destructed rocks zone height within the roof of a seam being mined upon the weakening of the rock mass due to its fissuring and mine working geometry has been determined. Effect of fissility on the periodical roof falling step has been studied. Changes in support loads in the process of stope advance have been determined. A scheme of partial backfilling of the worked out area has been proposed to maintain the support in its working order.

Experimental Bond Behavior of Mortar Grouted GFRP Rock Bolt

2011 ◽  
Vol 261-263 ◽  
pp. 1244-1248 ◽  
Author(s):  
Qi Neng Weng ◽  
Yong Yuan ◽  
Qian Guan Zhang
Keyword(s):  
Rock Mass ◽  
Concrete Block ◽  
Rock Bolt ◽  
Rock Bolts ◽  
Engineering Structures ◽  
Bond Behavior ◽  
Gfrp Bars ◽  
Pull Out ◽  
Glass Fiber Reinforced ◽  
Concrete Blocks

Bolts are widely used in slope engineering, tunnel and large cave supporting structures, as well as restoration of engineering structures. They can improve the strength and stability of ground, rock mass, and other structures. The traditional steel bolt has some disadvantages, such as easy corrosion, heavy weight, and difficult operation. Glass Fiber Reinforced Polymer (GFRP) is more resistant to chloride, stronger and lighter than steel. Those advantages make it a better alternative in some fields of engineering. To utilize GFRP bars as rock bolt, some aspects of its behavior, such as bond strength in mortar, bearing capacity, and bond stress distributing along its interface, have to be examined. This paper presents a research on bond behavior of GFRP rock bolts. A concrete block is used to represent rock mass in laboratory. Modified pull out tests were conducted on selected GFRP bars and compared with steel ones that were grouted with mortar in concrete blocks. Bond characteristics of mortar grouted GFRP rock bolts with diameter 16mm were mainly evaluated and other specs of bolts were also discussed.

scholarly journals Classification of Factors Affecting the Performance of Fully Grouted Rock Bolts with Empirical Classification Systems

2019 ◽  
Vol 9 (22) ◽  
pp. 4781 ◽  
Author(s):  
Haneol Kim ◽  
Hafeezur Rehman ◽  
Wahid Ali ◽  
Abdul Muntaqim Naji ◽  
Jung-joo Kim ◽  
...  
Keyword(s):  
Rock Mass ◽  
Field Experiments ◽  
Classification Systems ◽  
Rock Bolt ◽  
Rock Bolts ◽  
Tunnel Support ◽  
Support Materials ◽  
Pull Out ◽  
Controllable Factors ◽  
Grouted Rock Bolts

Empirical classification systems do not provide details of the factors that affect the performance of fully grouted rock bolts, as they are based on average values. Fully grouted rock-bolt patterns during tunnel-support design are a part of the composite support, and they are functions of rock-mass quality and tunnel span. Various fully grouted rock bolts are used in situ in different environments, along with other tunnel-support materials in static and dynamic environments during tunnel construction. The rock-bolt performances are evaluated through pull-out tests that follow ASTM standards. Several field pull-out tests were conducted on cement and resin grouted rock bolts. Under groundwater flow conditions, inflated steel tube rock bolts were tested and the results were compared with fully grouted rock bolts. Based on field experiments and previous studies, the factors that affect rock bolt performances are divided into five groups with respective sub-factors. Natural parameters cannot be controlled to ensure safety, economy, and stability in tunnels. The controllable factors, too, can be varied only within a practical range. In conclusion, the factors investigated here should be considered with the empirical support pattern of rock-mass classification systems for safe and economical design.

scholarly journals MODELLING ROCK MASS IMPROVEMENT USING ROCK BOLTS

2017 ◽  
Vol 10 ◽  
pp. 43 ◽  
Author(s):  
Jan Pruška
Keyword(s):  
Rock Mass ◽  
Rock Bolt ◽  
Numerical Calculations ◽  
Underground Excavation ◽  
Rock Bolts ◽  
Fem Modelling ◽  
Excavation Stability ◽  
Bolt Reinforcement ◽  
Grouted Bolts ◽  
Underground Constructions

Anchor support currently represents a significant reinforcing technique in underground constructions. The principles of rock bolt reinforcement action are derived from various concepts of the underground excavation stability. In recent times, rock bolt design techniques have been complemented by numerical calculations procedures. The paper describes FEM modelling of a rock bolt system for mechanical and grouted bolts.

scholarly journals Studying the performance of fully encapsulated rock bolts with modified structural elements

2021 ◽  
Author(s):  
Jianhang Chen ◽  
Hongbao Zhao ◽  
Fulian He ◽  
Junwen Zhang ◽  
Kangming Tao
Keyword(s):  
Shear Stress ◽  
Load Transfer ◽  
Maximum Shear Stress ◽  
Coupling Model ◽  
Numerical Approach ◽  
Rock Bolt ◽  
Structural Elements ◽  
Rock Bolts ◽  
Two Stage ◽  
Bolt Diameter

AbstractNumerical simulation is a useful tool in investigating the loading performance of rock bolts. The cable structural elements (cableSELs) in FLAC3D are commonly adopted to simulate rock bolts to solve geotechnical issues. In this study, the bonding performance of the interface between the rock bolt and the grout material was simulated with a two-stage shearing coupling model. Furthermore, the FISH language was used to incorporate this two-stage shear coupling model into FLAC3D to modify the current cableSELs. Comparison was performed between numerical and experimental results to confirm that the numerical approach can properly simulate the loading performance of rock bolts. Based on the modified cableSELs, the influence of the bolt diameter on the performance of rock bolts and the shear stress propagation along the interface between the bolt and the grout were studied. The simulation results indicated that the load transfer capacity of rock bolts rose with the rock bolt diameter apparently. With the bolt diameter increasing, the performance of the rock bolting system was likely to change from the ductile behaviour to the brittle behaviour. Moreover, after the rock bolt was loaded, the position where the maximum shear stress occurred was variable. Specifically, with the continuous loading, it shifted from the rock bolt loaded end to the other end.

scholarly journals Weightage Effect during Back-Calculation of Rock-Mass Quality from the Installed Tunnel Support in Rock-Mass Rating and Tunneling Quality Index System

2019 ◽  
Vol 9 (10) ◽  
pp. 2065 ◽  
Author(s):  
Jonguk Kim ◽  
Hafeezur Rehman ◽  
Wahid Ali ◽  
Abdul Muntaqim Naji ◽  
Hankyu Yoo
Keyword(s):  
Rock Mass ◽  
Quality Index ◽  
Rock Bolt ◽  
Rock Mass Rating ◽  
Rock Mass Quality ◽  
Back Calculation ◽  
The Difference ◽  
Bolt Spacing ◽  
Q System ◽  
Selection Of

In extensively used empirical rock-mass classification systems, the rock-mass rating (RMR) and tunneling quality index (Q) system, rock-mass quality, and tunnel span are used for the selection of rock bolt length and spacing and shotcrete thickness. In both systems, the rock bolt spacing and shotcrete thickness selection are based on the same principle, which is used for the back-calculation of the rock-mass quality. For back-calculation, there is no criterion for the selection of rock-bolt-spacing-based rock-mass quality weightage and shotcrete thickness along with tunnel-span-based rock-mass quality weightage. To determine this weightage effect during the back-calculation, five weightage cases are selected, explained through example, and applied using published data. In the RMR system, the weightage effect is expressed in terms of the difference between the calculated and back-calculated rock-mass quality in the two versions of RMR. In the Q system, the weightage effect is presented in plots of stress reduction factor versus relative block size. The results show that the weightage effect during back-calculation not only depends on the difference in rock-bolt-spacing-based rock-mass quality and shotcrete along with tunnel-span-based rock-mass quality, but also on their corresponding values.

Sign in / Sign up

Export Citation Format

Share Document