scholarly journals Strength Behavior of Mortar Using Slag As Partial Replacement of Cement

1970 ◽  
Vol 3 ◽  
Author(s):  
Md Moinul Islam ◽  
Md Saiful Islam ◽  
Md Aftabur Rahman ◽  
Amrita Das
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Cement Mortar ◽  
Partial Replacement ◽  
Strength Development ◽  
Test Results ◽  
Granulated Blast Furnace Slag ◽  
Strength Behavior ◽  
Furnace Slag ◽  
Curing Age

This paper presents an experimental investigation carried out to study the effects of Ground Granulated Blast Furnace Slag (GGBFS) on strength development of mortar and the optimum use of slag in mortar. Cement was partially replaced with seven percentages (10%, 20%, 30%, 40%, 50%, 60% and 70%) of slag by weight. Ordinary Portland cement (OPC) mortar was also prepared as reference mortar. A total of 400 cube and briquet mortar specimens were cast and compressive as well as tensile strength of the mortar specimens were determined at curing age of 3, 7, 14, 28, 60, 90 and 180 days. Test results show that strength increases with the increase of slag up to an optimum value, beyond which, strength values start decreasing with further addition of slag. Among the seven slag mortars, the optimum amount of cement replacement is about 40%, which provides 19% higher compressive strength and 25% higher tensile strength as compared to OPC mortar. KEY WORDS: Slag; Cement; Mortar; Compressive Strength; Tensile Strength; Hydration. DOI: http://dx.doi.org/10.3329/mist.v3i0.8053

scholarly journals Effect of Polypropylene Fiber, GGBS and Fly Ash over the Strength Aspects of Concrete: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 978-983
Author(s):  
Khalid Bashir Mir
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Polypropylene Fiber ◽  
Synthetic Fiber ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

In this review study the usage of three different kinds of constructional materials was discussed in detail. The three materials comprised of Ground Granulated Blast Furnace Slag, fly and polypropylene fiber. Ground Granulated Blast Furnace Slag is basically the slag derived after the quenching process of iron slag produced during the processing of iron in iron industry. Fly ash is the waste generated from the coal processing industries and is mainly used in the road constructions works. Polypropylene fiber is a synthetic fiber that has very high tensile strength and flexural strength. This fiber is also known as synthetic fiber as it is mainly used in the synthetic industry. Depending upon the results of previous studies over the usage of these materials various conclusions has been drawn which are as follows. The results of studies related to the usage of Ground Granulated Blast Furnace Slag as partial replacement of cement concluded that the most optimum usage percentage of Ground Granulated Blast Furnace Slag as partial replacement of cement was found to be between 20 percent and 30 percent and beyond this limit the strength of concrete was decreasing. The past studies related to the usage of fly ash as partial replacement of cement shoed that the most optimum usage percentage of fly ash was found to be between 15 percent to 20 percent and beyond this percentage the strength parameters of concrete such as compressive strength, flexural strength and split tensile strength starts declining up to a greater extent. The studies related to the usage of polypropylene fiber showed that the usage of this fiber increases the compressive strength of soil and the most optimum results were found between 1.0 percent to 1.5 percent usages of polypropylene fiber. Above this percentage there will be negative effect on the strength aspects and the compressive strength starts declining.

Early and Late Compressive Strengths Behaviour of Concrete with Blended South African Extenders

2019 ◽  
Vol 803 ◽  
pp. 302-308
Author(s):  
Abiodun Ebenezer Akinwale ◽  
Bolanle Deborah Ikotun ◽  
Ayo Samuel Afolabi
Keyword(s):  
Compressive Strength ◽  
South African ◽  
Control Sample ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Granulated Blast Furnace Slag ◽  
Compressive Strength Test ◽  
Furnace Slag ◽  
Curing Age

The use of different supplementary cementitious materials (SCMs) has attracted the interest of researchers for years. These materials have their advantages and dis-advantages. The optimal use of these SCMs in concrete may call for blending them together in concrete instead of using them individually. The blend may increase their quality as one disadvantages may be catered for by another one advantages. The present study focusses on investigating the effect of proportional combination of these SCMs on strength development. Three different South African SCMs (Ground granulated blast-furnace slag, Silica fume and Fly ash) were blended at different proportions and used as replacement of cement in concrete. Compressive strength test based on SANS 5860:2006 standard were adopted. The compressive test was performed on 16 different mixes at 7, 14, 28, 90 and 120 days curing periods. The water/cement ratio for all the mix was maintained at 0.5. The compressive strength results are desirable for each curing age at the 30% replacement of cement in which each SCM contributes 10% to the mix, greater strength value at curing age beyond 120 days compared to control sample was envisaged for this sample.

scholarly journals Effect of fine recycled aggregates on the properties of non-cement blended materials

2020 ◽  
Vol 323 ◽  
pp. 01018
Author(s):  
Wei-Ting Lin ◽  
Lukáš Fiala ◽  
An Cheng ◽  
Michaela Petříková
Keyword(s):  
Compressive Strength ◽  
Blast Furnace Slag ◽  
Interface Structure ◽  
Strength Test ◽  
Recycled Aggregates ◽  
Test Results ◽  
Granulated Blast Furnace Slag ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Furnace Slag

In this study, the different proportions of co-fired fly ash and ground granulated blast-furnace slag were used to fully replace the cement as non-cement blended materials in a fixed water-cement ratio. The recycled fine aggregates were replaced with natural fine aggregates as 10%, 20%, 30%, 40% and 50%. The flowability, compressive strength, water absorption and scanning electron microscope observations were used as the engineered indices by adding different proportions of recycled fine aggregates. The test results indicated that the fluidity cannot be measured normally due to the increase in the proportion of recycled fine aggregates due to its higher absorbability. In the compressive strength test, the compressive strength decreased accordingly as the recycled fine aggregates increased due to the interface structure and the performance of recycled aggregates. The fine aggregates and other blended materials had poor cementation properties, resulting in a tendency for their compressive strength to decrease. However, the compressive strength can be controlled above 35 MPa of the green non-cement blended materials containing 20% recycled aggregates.

Effect of Ground Granulated Blast Furnace Slag on Compressive Strength of POFA Blended Concrete

2015 ◽  
Vol 802 ◽  
pp. 142-148
Author(s):  
M.N. Noor Azline ◽  
Farah Nora Aznieta Abd Aziz ◽  
Arafa Suleiman Juma
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Strength Development ◽  
Replacement Level ◽  
Concrete Compressive Strength ◽  
Cement Replacement ◽  
Granulated Blast Furnace Slag ◽  
Strength Tests ◽  
Furnace Slag

The article reports a laboratory experimental programme that investigated effect of ground granulated blast furnace (GGBS) on compressive strength of POFA ternary concrete. Compressive strength tests were performed at a range of cements combinations, including 100%PC, two POFA levels for binary concrete, 35% and 45%, and 15%GGBS inclusion for POFA ternary concrete. The compressive strength results were examined in comparison to PC only and equivalent POFA binary concretes for up to 28 days. Results show that the reduction in compressive strength is greater with the higher cement replacement level for all concretes particularly for POFA binary concretes. However, 15%GGBS in POFA blended concrete has a comparable compressive strength compared to PC concrete at both, 35% and 45%, cement replacement levels except for ternary concrete at 0.65 w/c. In addition, the compressive strength of ternary concrete is slightly higher compared to binary concrete for all concrete combinations. Although there is no significant noticeable influence on strength development, the presence of GGBS did not adverse the strength development of POFA blended concrete. Thus, it can be concluded that GGBS compensates the adverse effect of POFA at early strength development.

scholarly journals THE EFFECT OF CERAMIC WASTE AS COARSE AGGREGATE ON STRENGTH PROPERTIES OF CONCRETE

2017 ◽  
Vol 36 (3) ◽  
pp. 691-696
Author(s):  
EE Ikponmwosa ◽  
SO Ehikhuenmen
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Control Sample ◽  
Strength Properties ◽  
Waste Material ◽  
Partial Replacement ◽  
Replacement Level ◽  
Ceramic Waste ◽  
Curing Age

This paper reports the findings on an experimental investigation of the effect of partial replacement of coarse aggregate with ceramic waste on strength properties of concrete. Compressive strength tests were conducted using 150x150x150mm cube specimens, while tensile strength was investigated using 150x300mm cylinder specimens. Results of tests show that workability, density, compressive and flexural strength of concrete decreased with increase in ceramic waste content. The compressive strength at 90 days curing age for the control sample was 24.67 N/mm2. Compressive strength values at 90 days curing age for  25%, 50% and 75% replacement levels were 21.78 N/mm2, 19.85 N/mm2and 17.85 N/mm2 respectively. The decrease in density and strength was due to ceramic waste being lighter and more porous than normal coarse aggregate. Tensile strength of concrete with ceramic waste decline gradually from 8.39 N/mm2 to 6.13 N/mm2 for the control and 75% replacement samples respectively. This could be attributed to the water absorption capacity and external porcelain nature of the waste material. A production cost savings of 10.7% for 1:2:4 concrete mix was noted at 75% replacement level. This study concludes that ceramic waste could be used for both structural and non-structural works and recommends that beyond 75% replacement level, ceramic waste material should not be used in concrete structures where strength is the major consideration. http://dx.doi.org/10.4314/njt.v36i3.5

scholarly journals Evaluation of Strength Development in Concrete with Ground Granulated Blast Furnace Slag Using Apparent Activation Energy

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 442 ◽  
Author(s):  
Hyun-Min Yang ◽  
Seung-Jun Kwon ◽  
Nosang Vincent Myung ◽  
Jitendra Kumar Singh ◽  
Han-Seung Lee ◽  
...  
Keyword(s):  
Activation Energy ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Apparent Activation Energy ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
Strength Development ◽  
Replacement Ratio ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Ground granulated blast furnace slag (GGBFS) conventionally has been incorporated with ordinary Portland cement (OPC) owing to reduce the environmental load and enhance the engineering performance. Concrete with GGBFS shows different strength development of normal concrete, but sensitive, to exterior condition. Thus, a precise strength evaluation technique based on a quantitative model like full maturity model is required. Many studies have been performed on strength development of the concrete using equivalent age which is based on the apparent activation energy. In this process, it considers the effect of time and temperature simultaneously. However, the previous models on the apparent activation energy of concrete with mineral admixtures have limitation, and they have not considered the effect of temperature on strength development. In this paper, the apparent activation energy with GGBFS replacement ratio was calculated through several experiments and used to predict the compressive strength of GGBFS concrete. Concrete and mortar specimens with 0.6 water/binder ratio, and 0 to 60% GGBFS replacement were prepared. The apparent activation energy (Ea) was experimentally derived considering three different curing temperatures. Thermodynamic reactivity of GGBFS mixed concrete at different curing temperature was applied to evaluate the compressive strength model, and the experimental results were in good agreement with the model. The results show that when GGBFS replacement ratio was increased, there was a delay in compressive strength.

scholarly journals Evolution of Mechanical Properties with Time of Fly-Ash-Based Geopolymer Mortars under the Effect of Granulated Ground Blast Furnace Slag Addition

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1135 ◽  
Author(s):  
Mateusz Sitarz ◽  
Izabela Hager ◽  
Marta Choińska
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Modulus Of Elasticity ◽  
Blast Furnace Slag ◽  
Energy Savings ◽  
Pulse Velocity ◽  
Partial Replacement ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Geopolymers are considered to alternatives to Portland cement, providing an opportunity to exploit aluminosilicate wastes or co-products with promising performances in the construction sector. This research is aimed at investigating the strength of fly-ash-geopolymers of different ages. The effect of granulated blast furnace slag (GGBFS) as a partial replacement of fly ash (FA) on the tensile (ft) and compressive strength (fc), as well as the modulus of elasticity, is investigated. The main advantage of the developed geopolymer mixes containing GGBFS is their ability to set and harden at room temperature with no need for heating to obtain binding properties, reducing the energy consumption of their production processes. This procedure presents a huge advantage over binders requiring heat curing, constituting a significant energy savings and reduction of CO2 emissions. It is found that the development of strength strongly depends on the ratio of fly-ash to granulated blast furnace slag. With the highest amount of GGBFS, the compressive strength of geopolymers made of fly-ash reached 63 MPa after 28 days of curing at ambient temperature. The evolution of compressive strength with time is correlated with the development of ultrasound pulse velocity methods, which are used to evaluate maturity. The modulus of elasticity changes with strength and the relationship obtained for the geopolymer is presented on the basis of typical models used for cement-based materials. The tensile to compressive strength ratios of the tested geopolymers are identified as higher than for cementitious binders, and the ft(fc) relationship is juxtaposed with dependencies known for cement binders, showing that the square root function gives the best fit to the results.

Effect of Corrosion Inhibitor on the Compressive Strength of Polymer-Modified Cement Mortars

2014 ◽  
Vol 692 ◽  
pp. 482-485
Author(s):  
Jae Eun Jeong ◽  
Keun Hyeok Yang ◽  
In Gu Yun
Keyword(s):  
Compressive Strength ◽  
Corrosion Inhibitor ◽  
Cement Mortar ◽  
Strength Development ◽  
Test Results ◽  
Initial Flow ◽  
Cement Mortars ◽  
Compressive Strength Development

This study examined initial flow and compressive strength development of polymer-modified cement mortar according to the addition of corrosion inhibitor. Test results showed that with the increase of the amount of corrosion inhibitor, the initial flow of mortars increased whereas compressive strength decreased. The strength development of mortar specimens could be reasonably predicted using the modified ACI 209 equations.

Sign in / Sign up

Export Citation Format

Share Document