scholarly journals THE EFFECT OF CERAMIC WASTE AS COARSE AGGREGATE ON STRENGTH PROPERTIES OF CONCRETE

2017 ◽  
Vol 36 (3) ◽  
pp. 691-696
Author(s):  
EE Ikponmwosa ◽  
SO Ehikhuenmen
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Control Sample ◽  
Strength Properties ◽  
Waste Material ◽  
Partial Replacement ◽  
Replacement Level ◽  
Ceramic Waste ◽  
Curing Age

This paper reports the findings on an experimental investigation of the effect of partial replacement of coarse aggregate with ceramic waste on strength properties of concrete. Compressive strength tests were conducted using 150x150x150mm cube specimens, while tensile strength was investigated using 150x300mm cylinder specimens. Results of tests show that workability, density, compressive and flexural strength of concrete decreased with increase in ceramic waste content. The compressive strength at 90 days curing age for the control sample was 24.67 N/mm2. Compressive strength values at 90 days curing age for  25%, 50% and 75% replacement levels were 21.78 N/mm2, 19.85 N/mm2and 17.85 N/mm2 respectively. The decrease in density and strength was due to ceramic waste being lighter and more porous than normal coarse aggregate. Tensile strength of concrete with ceramic waste decline gradually from 8.39 N/mm2 to 6.13 N/mm2 for the control and 75% replacement samples respectively. This could be attributed to the water absorption capacity and external porcelain nature of the waste material. A production cost savings of 10.7% for 1:2:4 concrete mix was noted at 75% replacement level. This study concludes that ceramic waste could be used for both structural and non-structural works and recommends that beyond 75% replacement level, ceramic waste material should not be used in concrete structures where strength is the major consideration. http://dx.doi.org/10.4314/njt.v36i3.5

scholarly journals Effect of Waste Tyre-Rubber Aggregate on the Strength Properties of Concrete

2018 ◽  
pp. 1-9
Author(s):  
Adetoye T. Oyebisi ◽  
Cordelia O. Osasona
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Strength Properties ◽  
Partial Replacement ◽  
Concrete Construction ◽  
Conventional Concrete ◽  
Waste Tyre ◽  
Rubber Aggregates

This research studied strength-characteristics of concrete using waste tyre-rubber as partial replacement for coarse aggregate in concrete construction and compares the results to those of conventional concrete. The specimens were produced with percentage replacements of the coarse aggregate by 5%, 10% and 15 % of rubber aggregate. A control mix with no replacement of the coarse aggregate was produced, to make a comparative analysis. The samples consisted of concrete cubes, cylinders and beams. Various tests (such as slump, compressive strength, splitting tensile strength and flexural strength tests), were conducted. Data-collection was mainly based on the results of the tests conducted on the specimens in the laboratory. The results show that there is a reduction in the compressive strength of the concrete, due to the inclusion of rubber aggregates. Compressive strength losses of 12.69%, 17.75% and 25.33% were noticed for 5%, 10%, 15% replacement of coarse aggregate, respectively; tensile strength losses of 13.01%, 20.12%, and 24.76% were observed, respectively, when 5%, 10%, 15% of the coarse aggregate was replaced, after 28 days of curing; -0.1%, -0.15% and 0.2% decrease in flexural strength was observed for 5%, 10% and 15% replacement, respectively, after curing for 28 days. Rubberised concrete was found to have some desirable characteristics (such as lower density, enhanced ductility, and a slight increase in flexural strength in the lower compressive strength concrete categories). The overall results show that it is possible to use recycled rubber tyres in concrete construction, as a partial replacement for coarse aggregates. Nevertheless, the percentage of replacement should be limited to 10% (which ensures the strength of the concrete is kept within the required range), and the application should be restricted to particular cases where the properties related to the replacement with the rubber aggregates clearly indicate an improvement on conventional concrete, and so are desirable.

scholarly journals Effect of Lightweight Waste-Based Aggregate on Lightweight Concrete

2019 ◽  
Vol 8 (4) ◽  
pp. 1041-1044
Keyword(s):  
Compressive Strength ◽  
Oil Palm ◽  
Coarse Aggregate ◽  
Lightweight Concrete ◽  
Bottom Ash ◽  
Control Sample ◽  
Waste Material ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Coal Bottom Ash

This paper study the effectiveness of waste material from industrial by-product as lightweight self-cured concrete. Waste material involved in this study is coal bottom ash, oil palm boiler clinker and hydrogel from diapers. Coal bottom ash (CBA) used as a fine aggregate replacement whilst oil palm clinker (OPBC) added into the concrete mixture as partial replacement of coarse aggregate in order to produce lightweight concrete. In addition, hydrogel from disposable diapers was acted as selfcuring agent. Different percentage of CBA as the fine aggregate replacement in concrete was used with the constant value of OPBC as coarse aggregate replacement. The result shows that the concrete sample containing 100% replacement of CBA has the lightest density as compared to other samples. In terms of compressive strength, the sample containing 40% replacement of CBA has similar compressive strength to control sample with reduction of the density of 22% when compared to the control sample. It is concluded that the recycling of CBA and OPBC as replacement material in lightweight concrete has good potential and also processing of CBA and OPBC to develop nano-material are the future potential of CBA and OPBC research for energy efficiency building.

scholarly journals Behavior of Steel Slag Concrete Subjected to Elevated Temperature

2020 ◽  
Vol 9 (4) ◽  
pp. 1165-1170
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Temperatures ◽  
Elevated Temperatures ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Partial Replacement ◽  
High Porosity ◽  
Residual Mechanical Properties

Recycling of materials has become a major interest for engineers. At present, the amount of slag deposited in storage yard adds up to millions of tons/year leading to the occupation of farm land and serious pollution to the environment, as a result of the rapid growth in the steel industry. Steel slag is made at 1500- 1650°C having a honey comp shape with high porosity. Using steel slag as the natural aggregate with a lower waste material cost can be considered as a good alternative for sustainable constructions. The objective of this study is to evaluate the performance of residual mechanical properties of concrete with steel slag as coarse aggregate partial replacement after exposing to high temperatures .This study investigates the behavior of using granulated slag as partial or fully coarse aggregate replacement with different percentages of 0%, 15%, 30%, 50% and 100% in concrete when subjected to elevated temperatures. Six groups of concrete mixes were prepared using various replacement percentages of slag exposed to different temperatures of 400 °C, 600 °C and 800 °C for different durations of 1hr, 1.5hr and 2hr. Evaluation tests were compressive strength, tensile strength, and bond strength. The steel slag concrete mixes showed week workability lower than control mix. A systematic increasing of almost up to 21.7% in compressive strength, and 66.2% in tensile strength with increasing the percentage of steel slag replacement to 50%. And the results showed improvement on concrete residual mechanical properties after subjected to elevated temperatures with the increase of steel slag content. The findings of this study give an overview of the effect of steel slag coarse aggregate replacement on concrete after exposed to high temperatures.

scholarly journals Mechanical Behaviour on Replacement of Aggregate by E-waste in Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 302-305 ◽  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Mechanical Behaviour ◽  
Coarse Aggregate ◽  
Environmental Problems ◽  
Waste Utilization ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Construction Work ◽  
Split Tensile Strength

Concrete is a widely used material in all construction work. The aim of the project is to study the behavior of concrete with replacement of E waste. The fine aggregate and coarse aggregate are naturally available due to increase in demand it is over exploited. The waste utilization is sustainable solution to environmental problems Waste from electric and electronic equipment is used as an E waste replacement for coarse aggregate in concrete which is used in the construction .Therefore the effects have been made to study the use of E waste components as a partial replacement of coarse aggregate in 5%, 10% and 15%. To determine the optimum percentage of E waste that can be replaced for coarse aggregate the compressive strength and split tensile strength of concrete to be studied. After determining the optimum percentage of E waste that can be replaced with coarse aggregate. The comparison of the conventional and optimum percentage of E waste replaced with concrete has been done

scholarly journals EFFICACY OF BASALT AND GRANITE AS COARSE AGGREGATE IN CONCRETE MIXTURE

2020 ◽  
Vol 7 (9) ◽  
pp. 1-9
Author(s):  
S.E Ubi ◽  
P.O Nkra ◽  
R.B Agbor ◽  
D.E Ewa ◽  
M. Nuchal
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Specific Gravity ◽  
Coarse Aggregate ◽  
Strength Properties ◽  
Test Results ◽  
Physical Test ◽  
Coarse Aggregates ◽  
Structural Tests ◽  
Comparative Results

This present research was on the comparison of the efficacious use of basalt and granite as coarse aggregates in concrete work. In order to obtain the basis for comparison, physical and structural tests were conducted on the different materials of the concrete and the concrete samples respectively. Physical test results revealed that basalt have a specific gravity of 2.8 and 2.5, while granite have a specific gravity of 2.9 and 2.6. In density, basalt have a density of 1554.55kg/m3 while granite had a density of 1463.64kg/m3. Aggregate impact test conducted on both aggregates revealed a percentage of 11.05% for basalt and 12.63% for granite. The following structural tests were carried out: compressive strength tests, flexural and tensile strength test and the comparative results are as follows. Compressive strength for basalt 36.39N/mm2 while 37.16N/mm2 for granite. 24.81N/mm2 tensile strength for basalt while 12.57N/mm2 for granite, 31.83N/mm2 flexural strength for basalt while 27.97N/mm2 for granite. From the above results, it can be deduced that basalt has higher strength properties than granite. Therefore, more suitable for coarse aggregate in achieving higher strength with some quantity of other composition of the concrete mix when compared to granite.

scholarly journals Strength and abrasion performance of recycled aggregate based geopolymer concrete

2021 ◽  
Author(s):  
Asfaw Mekonnen LAKEW ◽  
Mukhallad M. AL-MASHHADANI ◽  
Orhan CANPOLAT
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Coarse Aggregate ◽  
Steel Fiber ◽  
Splitting Tensile Strength ◽  
Partial Replacement ◽  
Geopolymer Concrete ◽  
Recycled Coarse Aggregate ◽  
One Year

This experimental work evaluated geopolymer concrete containing fly ash and slag by partial replacement of natural coarse aggregate (NCA) with recycled coarse aggregate (RCA) to manufacture environmental-friendly concrete. The proportion of recycled aggregates considered consists of 10%, 20%, 30%, and 40% of the total coarse aggregate amount. Also, a steel fiber ratio of 0.3% was utilized. The mechanical properties and abrasion resistance of fly ash/slag-based geopolymer concrete were then assessed. Majorly, the mechanical strength of the concrete samples decreased by the increase of RCA content. The geopolymer concrete with 40% RCA gave 28.3% lesser compressive strength and 24% lower splitting tensile strength than NCA concrete at one year. Also, the flexural strength of concrete specimens was reduced by 35% (from 5.34MPa to 3.5MPa) with the incorporation of 40% RCA. The incorporation of 30% RCA caused 23% and 22.6% reduction in compressive strength at 56 days and one year, respectively. The flexural and splitting tensile strength of the specimens was not significantly reduced (less than 10%) with the inclusion of a recycled coarse aggregate ratio of up to 30%. Furthermore, the abrasion wear thickness of every concrete sample was less than 1mm. RCA inclusion of 20% produced either insignificant reduction or better strength results compared to reference mixtures. As a result, it was considered that the combination of 0.3% steel fiber and 20% recycled coarse aggregate in fly ash/slag-based geopolymer concrete leads to an eco-friendly concrete mix with acceptable short and long-term engineering properties that would lead to sustainability in concrete production and utilization sector.

Research on Strength Properties of Concrete Using Aggregates from Repeatedly Recycling Concrete Waste

2014 ◽  
Vol 665 ◽  
pp. 147-150 ◽  
Author(s):  
Ping Hua Zhu ◽  
Yi Lei
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Strength Properties ◽  
Splitting Tensile Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Fine Aggregate ◽  
Replacement Ratio ◽  
Design Strength

The strength properties of recycled aggregate concrete (RAC) using aggregates from repeatedly recycling concrete waste were studied. The relationships between cube compressive strength and splitting tensile strength and between each strength and replacement ratio of recycled aggregate to natural aggregate were established. The results showed that the strength properties of RAC with the design strength of 30MPa can be satisfied when the quality of recycled coarse and fine aggregates met respectively the needs of Grade II in GB/T25177-2010 and Grade III in GB/T25176-2010, with the replacement ratio to natural coarse aggregate and natural fine aggregate no more than 70% and 50%. Both strengths decreased and then increased for a while before descending again with increasing replacement ratio of recycled coarse aggregate, and decreased continuously with the increase of replacement ratio of recycled fine aggregate. The relationship between cube compressive strength and splitting tensile strength of RAC was found to be exponential function.

scholarly journals Effects of Partial Replacement of Fine Aggregate with Quarry Dust on Concrete Properties

2020 ◽  
Vol 4 (1) ◽  
Author(s):  
S.O Ajamu ◽  
I.A Raheem ◽  
S.B Attah ◽  
J.O Onicha
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Replacement Level ◽  
River Sand ◽  
Split Tensile Strength ◽  
Stone Dust ◽  
Concrete Production ◽  
Quarry Dust

Natural river sand is one of the important constituent materials in concrete production while stone dust is a material obtained from crusher plants which is also sometimes being used either partially or fully in replacement of natural river sand in concrete production. Use of stone dust in concrete not only improves the quality of concrete but also conserve the natural river sand. However, due its scarcity and environmental degradation caused resulting from excessive mining of Natural river sand, there is need to investigate an alternative material of the same quality which can replace river sand in concrete production. In the present study, experiments were carried out to study the gradation of aggregates, workability, compressive strength and split tensile strength of concrete made using quarry dust as replacement of fine aggregate at 0, 25, 50, 75, and 100%. Grade M15 of concrete was produced with ordinary Portland cement (OPC) for referral concrete while M25 of concrete was prepared for compressive strength and split tensile strength concrete. Workability and Compressive strength were determined at different replacement level of fine aggregate and optimum replacement level was determined based on compressive strength. Results showed that by replacing 50% of fine aggregate with quarry dust, concrete of maximum compressive strength can be produced as compared to all other replacement levels. The effect of quarry dust on compressive strength and split tensile strength was investigated and from the overall result obtained, it was observed that the compressive strength and split tensile strength increased significantly for all the curing ages from 0% to 50% replacement level of quarry dust. Maximum value obtained for 28day compressive and tensile strength were 25N/mm2 and 2.3N/mm2 respectively and this occurred at 50% replacement.

scholarly journals Study on Strength Properties of Concrete with Ceramic Waste Aggregate and Silica Fume Admixture

2018 ◽  
Vol 7 (3.12) ◽  
pp. 831
Author(s):  
Suresh G ◽  
Harishankar S
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Silica Fume ◽  
Coarse Aggregate ◽  
Strength Properties ◽  
Industrial Wastes ◽  
Conventional Concrete ◽  
Ceramic Waste ◽  
Compressive Strength Of Concrete

The ceramic waste is used as a coarse aggregate replacement in concrete is a two way beneficial process that involves minimization of resources for construction and processing of hazardous industrial wastes that cannot be recycled. The ceramic waste obtained from waste dismantled building were used as coarse aggregate 10%, 20%, 30%, 40% and 50% replacement.  To improve the mechanical properties silica fume is added as admixture in the concrete. The optimum percentage replacement was obtained considering the strength as well as the objective of using ceramic waste aggregate. The compressive strength of concrete cubes were tested . The compressive strength of aggregate replaced concrete has been compared to that of conventional concrete and the results are evaluated. 

scholarly journals Experimental Investigation of Using Recycled Plastic Aggregates in Concrete with OPC 53 Grade

2021 ◽  
Vol 9 (8) ◽  
pp. 2918-2925
Author(s):  
Chevvu Krishnaveni
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
High Performance ◽  
Coarse Aggregate ◽  
Concrete Strength ◽  
Partial Replacement ◽  
Plastic Pollution ◽  
Split Tensile Strength ◽  
Polypropylene Fibres ◽  
Waste Products

Abstract: Plastic pollution is one of the greatest causes of global warming. Disposal of large quantity of plastic waste products causes environmental & health issues .This report will discuss a solution to plastic pollution by conducting to recycle the plastic and reuse in concrete, so the waste plastic is recycled into plastic aggregates. This paper aims to enhance the concrete mechanical properties by replacement of natural coarse aggregate with recycled plastic aggregates and by adding polypropylene fibers in combination with high performance cement as a partial replacement of cement. This both combinations in concrete gave excellent values of compressive strength and tensile strength. Replacement of coarse aggregate weight by 5%, 10%, 15%, 20%, 25% of recycled plastics and for each replacement percentages polypropylene fibres of 0.5%, 1.0%, 1.5%, 2.0% with partial replacement of cement were conducted. In literature reported that the addition of recycled plastic causes the reduction of strength due to poor bonding between concrete and plastics, to overcome this problem the addition of polypropylene fibres which has a good bonding property will improve the concrete strength were added. Result shows that 15% replacement of natural aggregates with plastic aggregate achieves the maximum strength of concrete. Keywords: Re-cycled plastic aggregates, polypropylene fibres, high performance cement, compressive strength, split tensile strength.

Sign in / Sign up

Export Citation Format

Share Document