scholarly journals Penambahan Serbuk Kayu Kamper terhadap Kuat Tekan Beton

2021 ◽  
Vol 9 (2) ◽  
pp. 85-92
Author(s):  
Lydia Darmiyanti ◽  
Gali Pribadi ◽  
Achmad Pahrul Rodji
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Furniture Industry ◽  
Wood Powder ◽  
Organic Fiber ◽  
Sand Mixture ◽  
Compressive Strength Of Concrete

Sawdust waste from the furniture industry should be considered. Nowadays, the increased demand for furniture is in line with the increase in sawdust waste produced. Therefore, it is necessary to make use of sawdust to protect environment. An alternative use is the addition of sawdust as the concrete mixture. Cellulose and hemicellulose compounds are compounds contained in wood powder, where these compounds can provide additional bonding between particles in the cement and sand mixture in concrete. Therefore, concrete can be stronger as well as more water resistant, hence it can be used for a specific purpose in constructions. This study aims to analyze the compressive strength of concrete due to the addition of sawdust as an organic fiber in the concrete mixture with the percentage of 0.25%, 0.50%, 0.75% and 1% as substitution of sand. Organic fibers as additives in concrete are being developed until recently. The proposed concrete was 25 MPa quality. Result showed the increase in the compressive strength of concrete by 0.98% in 1% wood powder mixed at 28 days of concrete age.

scholarly journals Pengaruh Penambahan Sat Additive Addition H.E Terhadap Kuat Tekan Beton

2020 ◽  
Vol 2 (1) ◽  
pp. 31-57
Author(s):  
Ni Ketut Sri Astati Sukawati
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Partial Replacement ◽  
Work Related ◽  
Coarse Aggregates ◽  
Alternative Ingredients ◽  
Fine Aggregates ◽  
Compressive Strength Test ◽  
Compressive Strength Of Concrete ◽  
Artificial Stone

Concrete with various variants is a basic requirement in building a building. The concrete mixture is diverse depending on the planning made beforehand. The cement mixture is usually in the form of a mixture of artificial stone, cement, water and fine aggregates and coarse aggregates. Aggregates (fine aggregates and coarse aggregates) function as fillers in concrete mixtures. (Subakti, A., 1994). However, in building construction, additives are often added, but there is still a sense of uncertainty at the time of dismantling the mold and the reference before the concrete reaches sufficient strength to carry its own weight and the carrying loads acting on it. To overcome the time of carrying out work related to concrete, it is necessary to find an alternative solution, for example by looking for alternative ingredients of concrete mixture on the basis of consideration without reducing the quality of the concrete. From the results of previous studies it was stated that due to the partial replacement of cement with Fly Ash, the strength of the pressure and tensile strength of the concrete had increased (Budhi Saputro, A., 2008). Based on the description above, the author seeks to examine how the compressive strength of concrete characteristics that occur by adding additives Addition H.E in the concrete mixture and is there any additive Additon H.E effect on the increase in the compressive strength characteristic of the concrete. From the results of the study, it was found that the compressive strength of the concrete with the addition of additives HE was that after the compressive strength test of the concrete cube was carried out and the analysis of concrete compressive strength of 10 specimens, in each experiment a cube specimen was made with the addition of additons. HE with a dose of 80 cc, 120 cc, and 200 cc can accelerate and increase the compressive strength of concrete characteristics.

scholarly journals Pengaruh Pemanfaatan Abu Tumbuhan Perumpung Terhadap Peningkatan Kuat Tekan Beton K300

Jurnal Tekno ◽  
2021 ◽  
Vol 18 (2) ◽  
pp. 11-20
Author(s):  
Ahmad Junaidi ◽  
R Dewo Hiraliyamaesa Hariyanto
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Wild Plant ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Compressive Strength Of Concrete ◽  
Test Objects

Perumpung (Eulalia japonica) is a wild plant that usually grows on the banks of river. The locals consider this plant as a waste/pest, but the authors are interested in researching perumpung because they are similar to bamboo, sugarcane and other fibrous plants. In this study, the authors aims to compare the compressive strength of normal concrete with the compressive strength of concrete added with Perumpung ash at 28-days-old K-300. The study used a cube-shaped test object (15 x 15 x 15 cm) with 6 samples for each condition. The total number of test objects is 48, which consists of 8 conditions, namely normal conditions and 5%, 7.5%, 10%, 12.5%, 15%, 17.5% and 20% addition of perumpung ash by cement weight. The results obtained that the compressive strength of 28-days-old concrete under normal conditions was 316,060 kg/cm2 and the addition of 5% ash was 331.583 kg/cm2, 7.5% was 337.181 kg/cm2, 10% was 341.813 kg/cm2, 12 ,5% is 347,045 kg/cm2, 15% is 353,889 kg/cm2, 17.5% is 311,160 kg/cm2 and 20% is 298.44 kg/cm2. From the results above it can be concluded that the addition of 15% Perumpung Ash to the concrete mixture increases the maximum characteristic concrete compressive strength by 353.889 kg/cm2.

scholarly journals Kuat Tekan Beton Mutu Tinggi dengan Memanfaatkan Fly Ash dan Bubuk Kaca Sebagai Bahan Pengisi

2020 ◽  
Vol 20 (01) ◽  
pp. 61-68
Author(s):  
Siska Apriwelni ◽  
Nugraha Bintang Wirawan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Glass Powder ◽  
Concrete Mixture ◽  
Strength Testing ◽  
Concrete Compressive Strength ◽  
High Quality ◽  
Glass Waste ◽  
Powder Addition ◽  
Compressive Strength Of Concrete

(ID) Penelitian ini membahas pengaruh kuat tekan beton mutu tinggi dengan memanfaatkan limbah fly ash dan limbah kaca. Tujuan dari penelitian ini untuk mengetahui kuat tekan beton pada masing-masing variasi, mengetahui persentase campuran beton untuk menghasilkan kuat tekan maksimum, dan mengetahui apakah fly ash dan serbuk kaca efektif digunakan secara bersamaan sebagai bahan campuran beton. Komposisi fly ash terdiri dari 5 variasi yaitu persentase 0%, 5%, 10%, 15%, dan 20%. Sedangkan untuk komposisi serbuk kaca terdiri dari 2 variasi yaitu persentase 5% dan 10%. Jumlah benda uji 30 buah silinder berukuran diameter 15 cm dan tinggi 30 cm dengan 3 benda uji untuk setiap variasi. Perencanaan campuran beton menggunakan SNI 03-2834-2000 yang dimodifikasi. Pengujian kuat tekan diuji pada umur beton 28 hari. Beton dengan fly ash 0% dan serbuk kaca 10% memiliki kuat tekan paling tinggi dibandingkan dengan beton dengan tambahan fly ash, yaitu 46,77%. Selain itu, dapat disimpulkan bahwa semakin bertambahnya jumlah persentase serbuk kaca yang digunakan menunjukkan bahwa kuat tekan beton semakin bertambah juga. Penambahan fly ash pada campuran beton mempengaruhi kuat tekan beton yang dihasilkan. Pada variasi fly ash 0% memiliki kuat tekan tertinggi baik pada saat campuran serbuk kaca 5%dan 10%. Variasi fly ash 15% adalah kondisi optimum campuran beton dengan kuat tekan beton yaitu 43,31 Mpa. Kedua limbah ini dapat dikombinasikan dan dimanfaatkan dengan baik dan digunakan dalam pembuatan beton mutu tinggi. (EN) This study discusses the effect of high quality concrete by utilizing fly ash and glass waste. The purpose of this study is to determine the compressive strength of concrete in each variation, to determine the contribution of concrete to produce compressive strength, and to find out that fly ash and glass powder are effectively used in full as a concrete admixture. Fly ash composition consists of 5 variations, namely the percentage of 0%, 5%, 10%, 15%, and 20%. While for the composition of glass powder consists of 2 variations, namely the percentage of 5% and 10%. The number of specimens is 30 cylinders with a diameter of 15 cm and a height of 30 cm with 3 specimens for each variation. Concrete mixture planning using SNI 03-2834-2000 was developed. Compressive strength testing on concrete age 28 days. Concrete with 0% fly ash and 10% glass powder have the highest compressive strength compared to concrete with additional fly ash, which is 46.77%. In addition, it can increase the amount of glass powder addition that is used to show the concrete compressive strength is increasing as well. The addition of fly ash in the concrete mixture has an effect on the compressive strength of the concrete produced. In the variation of 0% fly ash has the highest compressive strength when the glass powder mixture of 5% and 10%. The 15% fly ash variation is the optimal concrete mixture with compressive strength of 43.31 MPa. These two wastes can be combined and utilized properly and are used in making high quality concrete.  

Compressive Strength of Concrete from Lightweight Bubbles Aggregate

2015 ◽  
Vol 754-755 ◽  
pp. 348-353 ◽  
Author(s):  
Norlia Mohamad Ibrahim ◽  
Leong Qi Wen ◽  
Mustaqqim Abdul Rahim ◽  
Khairul Nizar Ismail ◽  
Roshazita Che Amat ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Compressive Strength ◽  
Natural Resources ◽  
Concrete Structure ◽  
Concrete Mixture ◽  
New Materials ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

Compressive strength of concrete is the major mechanical properties of concrete that need to be focused on. Poor compressive strength will lead to low susceptibility of concrete structure towards designated actions. Many researches have been conducted to enhance the compressive strength of concrete by incorporating new materials in the concrete mixture. The dependencies towards natural resources can be reduced. Therefore, this paper presents the results of an experimental study concerning the incorporation of artificial lightweight bubbles aggregate (LBA) into cementations mixture in order to produce comparable compressive strength but at a lower densities. Three concrete mixtures containing various percentages of LBA, (10% - 50% of LBA) and one mixture used normal aggregate (NA) were prepared and characterized. The compressive strength of LBA in concrete was identified to be ranged between 39 MPa and 54 MPa. Meanwhile, the densities vary between 2000 kg/m3 to 2300 kg/m3.

scholarly journals Studi Perancangan Campuran Beton Menggunakan Abu Batu Sebagai Agregat Halus. (Hal. 108-117)

2019 ◽  
Vol 5 (3) ◽  
pp. 108
Author(s):  
Muhammad Malik Ibrahim ◽  
Priyanto Saelan
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Natural Sand ◽  
Additional Water ◽  
Compressive Strength Of Concrete ◽  
Concrete Materials ◽  
The Relationship ◽  
Water Ratio ◽  
Research Show

ABSTRAKSalah satu limbah yang dapat digunakan sebagai pengganti bahan pembuat beton adalah abu batu. Abu batu merupakan limbah dari proses pemecahan bongkahan batu. Ditinjau dari ukuran butirannya maka abu batu merupakan agregat halus. Abu batu memiliki penyerapan air yang lebih tinggi daripada pasir alami, maka dari itu untuk mendapatkan kelecakan campuran beton yang sama dengan kelecakan campuran beton menggunakan pasir alami, penggunaan abu batu sebagai agregat halus dalam campuran beton perlu tambahan air. Namun hal ini akan menyebabkan faktor air-semen bertambah. Sehingga hasil kuat tekan akan menurun. Hal ini sesuai dengan hubungan antara kuat tekan beton dengan faktor air-semen. Perekayasaan yang dilakukan adalah dengan menaikkan faktor granular (G) dan menaikkan kuat tekan rencana berdasarlan teori Dreux. Abu batu pada penelitian ini digunakan sebagai substitusi pasir alami dengan proporsi 0%, 20%, 40%, 60%, 80%, dan 100%. Hasil penelititan ini memperlihatkan penggunaan abu batu sebagai agregat halus lebih dari 40% akan sangat drastis menurunkan kuat tekan beton.Kata kunci: perekayasaan, substitusi, campuran beton, abu batu, agregat halus ABSTRACTOne of the wastes that can be used as a substitute for concrete materials is stone ash. Stone ash is a waste from the process of stone crusher. Consider from the size of the grain, stone ash as fine aggregate. Stone ash has a higher water absorption than natural sand, therefore to get the concrete workability that is the same as the concrete workability using natural sand, the use of stone ash as fine aggregate in the concrete mixture needs additional water. But this will cause the cement-water ratio to increase. So that the compressive strength will decrease. This is following the relationship between the compressive strength of concrete and the cement-water ratio. Engineering is done by increasing the granular factor (G) and increasing the compressive strength of the plan based on Dreux theory. Stone ash in this study was used as a substitute for natural sand with a proportion of 0%, 20%, 40%, 60%, 80%, and 100%. The results of this research show that the use of stone ash as fine aggregate of more than 40% will greatly reduce the compressive strength of the concrete.Keywords: engineering, substitute, concrete mixture, stone ash, fine aggregate

scholarly journals The influence of different type of aggregate, fly ash and fiber-reinforced polymer on splitting resistance in pretensioned concrete railroad ties

2021 ◽  
Vol 27 (4) ◽  
pp. 135-140
Author(s):  
Adrijana Savić ◽  
Robert Peterman
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Fiber Reinforced Polymer ◽  
Concrete Mixture ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Pretensioned Concrete ◽  
Edge Distance ◽  
Different Types ◽  
Compressive Strength Of Concrete

This research evaluates the influence of the different types of concrete mixture, using a shallow type of indentation of wire, having the different edge distance and compressive strength of concrete on splitting resistance in pretensioned concrete railroad sleepers. The investigated compressive strength of concrete was 4500psi. The research was experimental, and the part of this research was formally adapted in Arema StandardsforRailwayEngineering Chapter 30 section 4.2.4.

A review: sustainable compressive strength properties of concrete mix with replacement by marble powder

2020 ◽  
Vol 1 (98) ◽  
pp. 11-23
Author(s):  
N. Sharma ◽  
M. Singh Thakur ◽  
P.L. Goel ◽  
P. Sihag
Keyword(s):  
Compressive Strength ◽  
Design Methodology ◽  
Strength Properties ◽  
Concrete Mixture ◽  
Fine Aggregates ◽  
Concrete Mix ◽  
Marble Powder ◽  
Compressive Strength Of Concrete ◽  
The Impact

Purpose: Over the years, various experiments have been performed to investigate the impact of marble powder within the concrete mixture. In the present study, a review has been done to check the persistence of marble dirt as the substitute for concrete constituents. Design/methodology/approach: Furthermore, the impact of marble powder as a replacement of cement and aggregates were reviewed. By reviewing previous studies, the result indicates that the use of waste marble powder in cement and aggregate was adequate to a certain range. Findings: By replacing cement with marble powder in a range between 5% to 10% by weight, it increases the compressive strength of concrete mix by 11.30% to 24.56%, compared to the nominal mix. According to the study, any further increase in the amount of marble powder in place of cement i.e, 12.5% to 20% replacement by weight, results in the reduction of compressive strength of concrete mix by 7.5% to 26.01%. Replacement of aggregates from 5% to 75% with marble powder increases the compressive strength of about 3.22% to 23.91% as compared to the nominal mix. Research limitations/implications: It was also concluded from the current study that, to obtain higher compressive strength, it is advantageous to replace fine aggregates with marble powder than the replacement of cement with the marble powder.

scholarly journals OPTIMIZING THE USE OF ROCK ASH AS FINE AGGREGATES WITH THE ADDITION OF ADDITIVES TO THE CONCRETE MIXTURE WITH A COMPRESSIVE STRENGTH OF 350 Kg/cm2

CI-TECH ◽  
2020 ◽  
Vol 1 (01) ◽  
pp. 45-48
Author(s):  
Triaswati ◽  
Srie Subekti ◽  
Sulchan Arifin ◽  
Febri Aditya
Keyword(s):  
Compressive Strength ◽  
Test Object ◽  
Concrete Mixture ◽  
Normal Concrete ◽  
Type D ◽  
Cylinder Test ◽  
Fine Aggregates ◽  
Stone Dust ◽  
Compressive Strength Of Concrete

Stone dust nowadays is a side product of the stone crushing industry, the quality of which is quite a lot that it becomes a waste that needs to be handled. This study is intended to find out the composition of stone dust by adding some additive substance type D and type F to reach a compressive strength of 350 kg/cm2. The variation of percentage of stone dust on the composition of concrete mixture is 0%, 20%, 40%, 60%, 80%, 100%. The design of concrete mixture composition refers to the procedure of making preparation of the normal concrete mixture. SNI 03-2384-1993. The size of the cylinder test object is 15 cm in diameter and 30 cm in height. The result of this research shows that the mixture using stone dust has quite an effect on the compressive strength of concrete. From the result of the experiment, it is shown that for compressive strength of 350 kg/cm2, we can use 100% of stone dust with a resulted compressive strength of 445 kg/cm2.

scholarly journals THE EFFECT OF COMPARISON OF CONCRETE USING TANGKILING SAND AND KAPUAS SAND ON THE COMPRESSIVE STRENGTH OF CONCRETE

2020 ◽  
Vol 8 (1) ◽  
pp. 36-41
Author(s):  
Whendy Trissan ◽  
Yongki Pratomo
Keyword(s):  
Compressive Strength ◽  
Total Sample ◽  
Concrete Mixture ◽  
Fine Aggregate ◽  
Concrete Compressive Strength ◽  
Normal Concrete ◽  
Study Program ◽  
Fine Aggregates ◽  
Compressive Strength Of Concrete ◽  
Building Engineering

In general, concrete fillers are made from materials that are easily obtained, easily processed, and have the durability and strength that is very much needed in particular construction of coarse and fine aggregates, each region would have different aggregates as the main ingredients in making concrete. The research conducted aims to determine how the optimum compressive strength value of the concrete produced from the addition of Kapuas Sand to the concrete mixture. In this research, Kapuas Sand is used as a fine aggregate enhancer. The percentage variation of Kapuas red sand used in this study varies, namely 0%, 25%, 50%, 75%, and 100%. Concrete mixture planning using SNI 03-2834-2000. The test uses cylindrical specimens with a height of 30 cm, a diameter of 15 cm with a total sample of 10 cylinders for each addition of Kapuas Sand so that the total specimens are 50 cylinders. Testing is carried out at the age of 14 and 28 days in the Laboratory of Building Engineering Education Study Program, Faculty of Teacher Training and Education, University of Palangka Raya. The results of the compressive strength of concrete using a mixture of Kapuas Sand at 28 days 0% 25%, 50%, 75% and, 100% respectively were 24.71 MPa, 21.79 MPa, 25.36 MPa, 23 .3 MPa, and .22.62 MPa. This result shows the compressive strength value of concrete in the concrete mix with a percentage of 50% that is equal to 25.36 MPa while the compressive strength of normal concrete is 24.71 MPa so that the compressive strength of concrete is 2.66% of normal concrete compressive strength with age concrete compressive strength 28 days.

PENGARUH PENAMBAHAN LIMBAH GIPSUM TERHADAP KUAT TEKAN BETON

2020 ◽  
Vol 2 (1) ◽  
pp. 1-12
Author(s):  
Rafki Imani ◽  
Widiawati Purba ◽  
Rainaldi S Nainggolan
Keyword(s):  
Compressive Strength ◽  
Concrete Mixture ◽  
Main Constituent ◽  
Concrete Compressive Strength ◽  
Concrete Technology ◽  
Normal Concrete ◽  
Compressive Strength Of Concrete ◽  
Waste Mixture

AbstractConcrete is composed of three main constituent materials, namely cement, aggregate and water. The development of concrete technology in the trial of adding a mixture of materials continues to be done to achieve the desired strength and quality. In this experiment, the addition of gypsum waste was used as a concrete mixture to determine its effect on the compressive strength of concrete. The variation in the percentage of the addition of gypsum waste is 5%, 10%, and 15% with the age of treatment observed at 14 days and 28 days. The results showed that the normal compressive strength value at 14 days was 186.87 kg/cm2, while with the addition of gypsum waste mixture the concrete compressive strength at 5%, 10% and 15% were obtained 178.45 kg respectively /cm2, 101, 01 kg/cm2, 70.71 kg/cm2. Meanwhile the compressive strength value of normal concrete at 28 days is 164.44 kg/cm2, and the compressive strength value of concrete after mixed with gypsum waste at 28 days is obtained 157.04 kg/cm2, 88.89 kg/cm2, 62.22 kg/cm2. Based on the results it can be concluded that the addition of gypsum waste as a concrete mixture material can reduce the compressive strength values of normal concrete.Keywords : Concrete, compressive strength, and gypsum waste.AbstrakBahan beton terdiri dari semen, pasir, kerikil dan air. Perkembangan teknologi beton dalam uji coba penambahan bahan campuran terus dilakukan untuk mendapatkan kekuatan dan mutu beton yang diinginkan. Dalam penelitian ini, penambahan limbah gipsum dimaksudkan sebagai campuran beton untuk melihat pengaruhnya pada nilai kuat tekan beton. Variasi persentase penambahan limbah gipsum ini adalah sebesar 5%, 10%, dan 15% dengan umur perawatan diamati pada umur 14 hari dan 28 hari. Hasil penelitian menunjukkan bahwa nilai kuat tekan beton normal pada umur 14 hari diperoleh sebesar 186,87 kg/cm2, sementara dengan penambahan campuran limbah gipsum nilai kuat tekan beton pada persentase 5%, 10% dan 15% secara berurutan diperoleh sebesar 178,45 kg/cm2, 101, 01 kg/cm2, 70,71 kg/cm2. Sementara nilai kuat tekan beton normal pada umur 28 hari adalah sebesar 164,44 kg/cm2, dan nilai kuat tekan beton setelah dicampur limbah gipsum pada umur 28 hari secara berurutan diperoleh sebesar 157,04 kg/cm2, 88,89 kg/cm2, 62,22 kg/cm2. Hasil penelitian menyimpulkan bahwa penambahan limbah gipsum sebagai bahan campuran beton dapat mengurangi nilai kuat tekan beton dibandingkan dengan kuat tekan beton normal. Kata kunci : Beton, kuat tekan dan limbah gipsum.

Sign in / Sign up

Export Citation Format

Share Document