scholarly journals The Bent-Tube Nozzle Optimization of Force-Spinning With the Gray Wolf Algorithm

2021 ◽  
Vol 9 ◽  
Author(s):  
Kang Liu ◽  
Wenhui Li ◽  
Peiyan Ye ◽  
Zhiming Zhang ◽  
Qiaoling Ji ◽  
...  
Keyword(s):  
Diameter Distribution ◽  
Curvature Radius ◽  
Gray Wolf ◽  
Straight Tube ◽  
Structure Parameters ◽  
Solution Flow ◽  
Bending Angle ◽  
Industrial Manufacture ◽  
The Mathematical Model ◽  
The Relationship

Force-spinning is a popular way to fabricate various fine fibers such as polymer and metal nanofibers, which are being widely employed in medical and industrial manufacture. The spinneret is the key of the device for spinning fibers, and the physical performance and morphology of the spun nanofibers are largely determined by its structure parameters. In this article, the effect of spinneret parameters on the outlet velocity is explored and the spinneret parameters are also optimized to obtain the maximum outlet velocity. The mathematical model of the solution flow in four areas is established at first, and the relationship between outlet velocity and structure parameters is acquired. This model can directly reflect the flow velocity of the solution in each area. Then, the optimal parameters of outlet diameter, bending angle, and curvature radius are obtained combined with the gray wolf algorithm (GWA). It is found that a curved-tube nozzle with a bending angle of 9.1°, nozzle diameter of 0.6 mm, and curvature radius of 10 mm can obtain the maximum outlet velocity and better velocity distribution. Subsequently, the simulation is utilized to analyze and compare the velocity situation of different parameters. Finally, the fiber of 5 wt% PEO solution is manufactured by a straight-tube nozzle and optimized bent-tube nozzle in the laboratory, and the morphology and diameter distribution were observed using a scanning electron microscope (SEM). The results showed that the outlet velocity was dramatically improved after the bent-tube parameters were optimized by GWA, and nanofibers of better surface quality could be obtained using optimized bent-tube nozzles.

Simulation of Yarn Tension Control System Based on Simulink

2010 ◽  
Vol 426-427 ◽  
pp. 106-108 ◽  
Author(s):  
De Gong Chang ◽  
Zhi Juan Xiao ◽  
Y.H. Liu ◽  
H. Li
Keyword(s):  
Control System ◽  
Dynamic Performance ◽  
Digital Simulation ◽  
Tension Control ◽  
Structure Parameters ◽  
Yarn Tension ◽  
Magnetic Powder Brake ◽  
Tension Control System ◽  
The Mathematical Model ◽  
The Relationship

Based on the analyses of the yarn tension and the mathematical model of the magnetic powder brake, the digital simulation of the yarn tension fuzzy control system was performed by using MATLAB Simulink. The relationship between the structure parameters and the system dynamic performance was then obtained, and the system scheme was justified.

Temperature Influence on Performance of Oxidation Ponds

1991 ◽  
Vol 24 (5) ◽  
pp. 85-96 ◽  
Author(s):  
Qingliang Zhao ◽  
Zijie Zhang
Keyword(s):  
Mathematical Model ◽  
Temperature Influence ◽  
Field Scale ◽  
Experiment Data ◽  
Computer Technique ◽  
Oxidation Pond ◽  
Optimum Model ◽  
Oxidation Ponds ◽  
The Mathematical Model ◽  
The Relationship

By means of simulated tests of a laboratory–scale oxidation pond model, the relationship between BOD5 and temperature fluctuation was researched. Mathematical modelling for the pond's performance and K1determination were systematically described. The calculation of T–K1–CeCe/Ci) was complex but the problem was solved by utilizing computer technique in the paper, and the mathematical model which could best simulate experiment data was developed. On the basis of experiment results,the concept of plug–ratio–coefficient is also presented. Finally the optimum model recommended here was verified with the field–scale pond data.

Numerical Simulation on Velocity Profiles of Mill Bearing Lubrication

2010 ◽  
Vol 145 ◽  
pp. 282-286
Author(s):  
Qing Xue Huang ◽  
Jian Mei Wang ◽  
Yu Gui Li ◽  
Li Feng Ma ◽  
Chun Jiang Zhao
Keyword(s):  
Cross Section ◽  
Velocity Profiles ◽  
Flow State ◽  
Oil Film ◽  
Velocity Gradients ◽  
Oil Flow ◽  
The Mathematical Model ◽  
The Relationship ◽  
General Velocity ◽  
Oil Film Pressure

No 460 oil-film bearing oil as the dedicated lubricant is regarded as the incompressible Newtonian fluid. To comprehensively analyze the real oil flow state, the mathematical model on velocity profiles, together with its dimensionless equations, is established, and the calculating program is developed to simulate the 3D velocity profiles and velocity gradients at different oil flow layers. The relationship between velocity profiles and the oil film pressure is discussed, and the velocity tendency is consistent with the general velocity profile of wedge cross section. The conclusions are beneficial to the further study on lubricating performances of heavy contact components and to prolong their service lives.

scholarly journals Experimental-numerical studies of the effect of cell structure on the mechanical properties of polypropylene foams

e-Polymers ◽  
2020 ◽  
Vol 20 (1) ◽  
pp. 713-723
Author(s):  
Wei Gong ◽  
Tuan-Hui Jiang ◽  
Xiang-Bu Zeng ◽  
Li He ◽  
Chun Zhang
Keyword(s):  
Mechanical Properties ◽  
Size Distribution ◽  
Cell Size ◽  
Cell Structure ◽  
Structure Parameters ◽  
Cell Size Distribution ◽  
Numerical Studies ◽  
Polypropylene Foam ◽  
The Impact ◽  
The Relationship

AbstractThe effects of the cell size and distribution on the mechanical properties of polypropylene foam were simulated and analyzed by finite element modeling with ANSYS and supporting experiments. The results show that the reduced cell size and narrow size distribution have beneficial influences on both the tensile and impact strengths. Decreasing the cell size or narrowing the cell size distribution was more effective for increasing the impact strength than the tensile strength in the same case. The relationship between the mechanical properties and cell structure parameters has a good correlation with the theoretical model.

Modified Model for Static Behavior of Microcantilever Gas Sensor Adsorbed with Monolayer Molecules

2011 ◽  
Vol 415-417 ◽  
pp. 455-459
Author(s):  
Xiao Ming Wang ◽  
Fei Wang ◽  
Xue Zeng Zhao ◽  
Da Lei Jing
Keyword(s):  
Young’S Modulus ◽  
Young's Modulus ◽  
Curvature Radius ◽  
Static Behavior ◽  
Neutral Layer ◽  
Modified Model ◽  
Adsorbed Molecules ◽  
Microcantilever Sensors ◽  
The Relationship ◽  
Layer Position

The modified static bending model of microcantilever with monolayer molecules has been established based on energy method, in which the change in neutral layer position caused by adsorption-induced stress has been considered. On this basis, we have analyzed the relationship between the bending curvature radius of a microcantilever with its thickness, Young’s modulus and molecule-molecule distance of adsorbed molecules when it is adsorbed with monolayer water molecules. Additionally, we have investigated the effect of change in neutral layer position on the static behavior of microcantilever sensors and have found that: 1) the bending curvature radius of microcantilever is affected by its Young’s modulus, thickness and distance of adsorbed molecules respectively; 2)the predicted error of bending curvature radius caused by the change in neutral layer position slightly increases with decreasing Young’s modulus and thickness, whereas the effect of distance between adsorbed molecules on the error is significant.

scholarly journals The relative compliance of energy-storing tendons may be due to the helical fibril arrangement of their fascicles

2017 ◽  
Vol 14 (133) ◽  
pp. 20170261 ◽  
Author(s):  
Tom Shearer ◽  
Chavaunne T. Thorpe ◽  
Hazel R. C. Screen
Keyword(s):  
Flexor Tendon ◽  
Extensor Tendon ◽  
Mechanical Tension ◽  
Superficial Digital Flexor Tendon ◽  
Microstructural Model ◽  
And Function ◽  
Nonlinear Elastic ◽  
The Mathematical Model ◽  
The Relationship ◽  
Fitting Parameters

A nonlinear elastic microstructural model is used to investigate the relationship between structure and function in energy-storing and positional tendons. The model is used to fit mechanical tension test data from the equine common digital extensor tendon (CDET) and superficial digital flexor tendon (SDFT), which are used as archetypes of positional and energy-storing tendons, respectively. The fibril crimp and fascicle helix angles of the two tendon types are used as fitting parameters in the mathematical model to predict their values. The outer fibril crimp angles were predicted to be 15.1° ± 2.3° in the CDET and 15.8° ± 4.1° in the SDFT, and the average crimp angles were predicted to be 10.0° ± 1.5° in the CDET and 10.5° ± 2.7° in the SDFT. The crimp angles were not found to be statistically significantly different between the two tendon types ( p = 0.572). By contrast, the fascicle helix angles were predicted to be 7.9° ± 9.3° in the CDET and 29.1° ± 10.3° in the SDFT and were found to be statistically highly significantly different between the two tendon types ( p < 0.001). This supports previous qualitative observations that helical substructures are more likely to be found in energy-storing tendons than in positional tendons and suggests that the relative compliance of energy-storing tendons may be directly caused by these helical substructures.

scholarly journals METHODS OF FORMULATING AND SOLVING OPTIMIZATION PROBLEMS OF CUTTING LOGS OF LARGE SIZE BY BAR-SAWING METHOD WITH CUTTING OUT ONE BAR AND FIVE PAIRS OF SIDE EDGING BOARDS WITH SUBSEQUENT SAWING LUMBER FOR EDGED BOARDS

2017 ◽  
Vol 7 (1) ◽  
pp. 137-150
Author(s):  
Агапов ◽  
Aleksandr Agapov
Keyword(s):  
Mathematical Model ◽  
Objective Function ◽  
Optimization Problem ◽  
Optimization Problems ◽  
Target Function ◽  
Cross Sectional ◽  
Optimization Task ◽  
Cutting Out ◽  
The Mathematical Model ◽  
The Relationship

For the first time the mathematical model of task optimization for this scheme of cutting logs, including the objective function and six equations of connection. The article discusses Pythagorean area of the logs. Therefore, the target function is represented as the sum of the cross-sectional areas of edging boards. Equation of the relationship represents the relationship of the diameter of the logs in the vertex end with the size of the resulting edging boards. This relationship is described through the use of the Pythagorean Theorem. Such a representation of the mathematical model of optimization task is considered a classic one. However, the solution of this mathematical model by the classic method is proved to be problematic. For the solution of the mathematical model we used the method of Lagrange multipliers. Solution algorithm to determine the optimal dimensions of the beams and side edging boards taking into account the width of cut is suggested. Using a numerical method, optimal dimensions of the beams and planks are determined, in which the objective function takes the maximum value. It turned out that with the increase of the width of the cut, thickness of the beam increases and the dimensions of the side edging boards reduce. Dimensions of the extreme side planks to increase the width of cut is reduced to a greater extent than the side boards, which are located closer to the center of the log. The algorithm for solving the optimization problem is recommended to use for calculation and preparation of sawing schedule in the design and operation of sawmill lines for timber production. When using the proposed algorithm for solving the optimization problem the output of lumber can be increased to 3-5 %.

Sign in / Sign up

Export Citation Format

Share Document