scholarly journals Surface Functionalization of Three Dimensional-Printed Polycaprolactone-Bioactive Glass Scaffolds by Grafting GelMA Under UV Irradiation

2020 ◽  
Vol 7 ◽  
Author(s):  
Farnaz Ghorbani ◽  
Melika Sahranavard ◽  
Zohre Mousavi Nejad ◽  
Dejian Li ◽  
Ali Zamanian ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Surface Roughness ◽  
Surface Modification ◽  
Bioactive Glass ◽  
Uv Irradiation ◽  
Three Dimensional ◽  
Homogeneous Distribution ◽  
X Ray ◽  
Fused Deposition ◽  
3D Printed

In this study, bioactive glass nanoparticles (BGNPs) with an average diameter of less than 10 nm were synthesized using a sol-gel method and then characterized by transmission electron microscopy (TEM), differential scanning calorimetric (DSC), Fourier transforms infrared spectroscopy (FTIR), and x-ray spectroscopy (XRD). Afterward, three dimensional (3D)-printed polycaprolactone (PCL) scaffolds along with fused deposition modeling (FDM) were incorporated with BGNPs, and the surface of the composite constructs was then functionalized by coating with the gelatin methacryloyl (GelMA) under UV irradiation. Field emission scanning electron microscopy micrographs demonstrated the interconnected porous microstructure with an average pore diameter of 260 µm and homogeneous distribution of BGNPs. Therefore, no noticeable shrinkage was observed in 3D-printed scaffolds compared with the computer-designed file. Besides, the surface was uniformly covered by GelMA, and no effect of surface modification was observed on the microstructure while surface roughness increased. The addition of the BGNPs the to PCL scaffolds showed a slight change in pore size and porosity; however, it increased surface roughness. According to mechanical analysis, the compression strength of the scaffolds was increased by the BGNPs addition and surface modification. Also, a reduction was observed in the absorption capacity and biodegradation of scaffolds in phosphate-buffered saline media after the incorporation of BGNPs, while the presence of the GelMA layer increased the swelling potential and stability of the composite matrixes. Moreover, the capability of inducing bio-mineralization of hydroxyapatite-like layers, as a function of BGNPs content, was proven by FE-SEM micrographs, EDX spectra, and x-ray diffraction spectra (XRD) after soaking the obtained samples in concentrated simulated body fluid. A higher potential of the modified constructs to interact with the aqueous media led to better precipitation of minerals. According to in-vitro assays, the modified scaffolds can provide a suitable surface for the attachment and spreading of the bone marrow mesenchymal stem cells (BMSCs). Furthermore, the number of the proliferated cells confirms the biocompatibility of the scaffolds, especially after a modification process. Cell differentiation was verified by alkaline phosphatase activity as well as the expression of osteogenic genes such as osteocalcin and osteopontin. Accordingly, the scaffolds showed an initial potential for reconstruction of the injured bone.

scholarly journals Surface Roughness Effect on the 3d Printed Butt Joints Strength

2015 ◽  
Author(s):  
V. Kovan ◽  
G. Altan ◽  
E.S. Topal ◽  
H.E. Camurlu
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Three Dimensional ◽  
Thickness Effect ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Object

Three-dimensional printing or 3D printing (also called additive manufacturing) is any of various processes used to make a three-dimensional object. Fused deposition modelling (FDM) is an additive manufacturing technology commonly used for modelling, prototyping, and production applications. It is one of the techniques used for 3D printing. FDM is somewhat restricted in the size and the variation of shapes that may be fabricated. For parts too large to fit on a single build, for faster job builds with less support material, or for parts with finer features, sectioning and bonding FDM parts is a great solution. The strength of adhesive bonded FDM parts is affected by the surface roughness. In this study, the layer thickness effect on bonding strength is experimentally studied and the results are discussed.

Analysis of Correlation Between Contrast and Component of Polylatic Acid Composite for Fused Deposition Modeling 3D Printing

2020 ◽  
Vol 20 (8) ◽  
pp. 5107-5111
Author(s):  
Kyu-Hyon Son ◽  
Jung-Hun Kim ◽  
Dong-Eun Kim ◽  
Min-Sik Kang ◽  
Joo-Heon Song ◽  
...  
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Disruptive Technology ◽  
X Ray ◽  
Fused Deposition ◽  
Potential Applicability ◽  
Deposition Modeling ◽  
3D Printed ◽  
Cie Lab

Additive manufacturing or three-dimensional (3D) printing is considered a disruptive technology for producing components with topologically optimized complex geometries as well as functionalities that are not achievable by traditional methods. 3D printing is expected to revolutionize the manufacturing of components. While several 3D printing systems are available, printing based on fused-deposition modeling (FDM) using thermoplastics is particularly widespread because of the simplicity and potential applicability of the method. In this study, we report the analysis of correlation between contrast and component of polylactic acid (PLA) based composite for FDM 3D printing. The pre-fabricated white composite and black composite were mixed in the fraction of 100:0, 90:10, 75:25, 50:50, 25:75, and 0:100% (v/v) and the obtained mixture was extruded using HX-35 3D filament extrusion line. The samples in different contrast were printed in disk like shape, and the gray scale filaments and 3D printed samples were measured the morphology and components using a field emission scanning electron microscope and energy dispersive X-ray spectroscopy. The CIE-lab values of the samples were measured using a colorimeter and the correlation between CIE-lab values and the components were analyzed. Although the component of Ti was linearly increased, the CIE-lab values show a clear exponential increase by increasing the white composite.

scholarly journals Mechanical Characterization and Thermodynamic Analysis of Laser-Polished Landscape Design Products Using 3D Printing

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2601
Author(s):  
Yue Ba ◽  
Yu Wen ◽  
Shibin Wu
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
High Surface ◽  
Landscape Design ◽  
Laser Polishing ◽  
Fused Deposition ◽  
Design Structure ◽  
3D Printed ◽  
Stability And Accuracy

Recent innovations in 3D printing technologies and processes have influenced how landscape products are designed, built, and developed. In landscape architecture, reduced-size models are 3D-printed to replicate full-size structures. However, high surface roughness usually occurs on the surfaces of such 3D-printed components, which requires additional post-treatment. In this work, we develop a new type of landscape design structure based on the fused deposition modeling (FDM) technique and present a laser polishing method for FDM-fabricated polylactic acid (PLA) mechanical components, whereby the surface roughness of the laser-polished surfaces is reduced from over Ra 15 µm to less than 0.25 µm. The detailed results of thermodynamics and microstructure evolution are further analyzed during laser polishing. The stability and accuracy of the results are evaluated based on the standard deviation. Additionally, the superior tensile and flexural properties are examined in the laser-polished layer, in which the ultimate tensile strength (UTS) is increased by up to 46.6% and the flexural strength is increased by up to 74.5% compared with the as-fabricated components. Finally, a real polished landscape model is simulated and optimized using a series of scales.

scholarly journals Multi-Scale Studies of 3D Printed Mn–Na–W/SiO2 Catalyst for Oxidative Coupling of Methane

Catalysts ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 290
Author(s):  
Tim Karsten ◽  
Vesna Middelkoop ◽  
Dorota Matras ◽  
Antonis Vamvakeros ◽  
Stephen Poulston ◽  
...  
Keyword(s):  
Oxidative Coupling ◽  
Oxidative Coupling Of Methane ◽  
Operating Conditions ◽  
Homogeneous Distribution ◽  
Silica Support ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
X Ray ◽  
Multi Scale ◽  
3D Printed

This work presents multi-scale approaches to investigate 3D printed structured Mn–Na–W/SiO2 catalysts used for the oxidative coupling of methane (OCM) reaction. The performance of the 3D printed catalysts has been compared to their conventional analogues, packed beds of pellets and powder. The physicochemical properties of the 3D printed catalysts were investigated using scanning electron microscopy, nitrogen adsorption and X-ray diffraction (XRD). Performance and durability tests of the 3D printed catalysts were conducted in the laboratory and in a miniplant under real reaction conditions. In addition, synchrotron-based X-ray diffraction computed tomography technique (XRD-CT) was employed to obtain cross sectional maps at three different positions selected within the 3D printed catalyst body during the OCM reaction. The maps revealed the evolution of catalyst active phases and silica support on spatial and temporal scales within the interiors of the 3D printed catalyst under operating conditions. These results were accompanied with SEM-EDS analysis that indicated a homogeneous distribution of the active catalyst particles across the silica support.

scholarly journals 3D Printed Masks for Powders and Viruses Safety Protection Using Food Grade Polymers: Empirical Tests

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 617
Author(s):  
Ruben Foresti ◽  
Benedetta Ghezzi ◽  
Matteo Vettori ◽  
Lorenzo Bergonzi ◽  
Silvia Attolino ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Material Selection ◽  
Mechanical Resistance ◽  
Biological Safety ◽  
Fused Deposition ◽  
Industrial Grade ◽  
Safety Protection ◽  
3D Printed ◽  
Manufacturing Technologies

The production of 3D printed safety protection devices (SPD) requires particular attention to the material selection and to the evaluation of mechanical resistance, biological safety and surface roughness related to the accumulation of bacteria and viruses. We explored the possibility to adopt additive manufacturing technologies for the production of respirator masks, responding to the sudden demand of SPDs caused by the emergency scenario of the pandemic spread of SARS-COV-2. In this study, we developed different prototypes of masks, exclusively applying basic additive manufacturing technologies like fused deposition modeling (FDM) and droplet-based precision extrusion deposition (db-PED) to common food packaging materials. We analyzed the resulting mechanical characteristics, biological safety (cell adhesion and viability), surface roughness and resistance to dissolution, before and after the cleaning and disinfection phases. We showed that masks 3D printed with home-grade printing equipment have similar performances compared to the industrial-grade ones, and furthermore we obtained a perfect face fit by customizing their shape. Finally, we developed novel approaches to the additive manufacturing post-processing phases essential to assure human safety in the production of 3D printed custom medical devices.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

scholarly journals Dimensional Accuracy of Dental Models for Three-Unit Prostheses Fabricated by Various 3D Printing Technologies

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1550
Author(s):  
Soo-Yeon Yoo ◽  
Seong-Kyun Kim ◽  
Seong-Joo Heo ◽  
Jai-Young Koak ◽  
Joung-Gyu Kim
Keyword(s):  
Surface Roughness ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
3D Analysis ◽  
Digital Light Processing ◽  
Test Models ◽  
Reference File ◽  
Significant Difference ◽  
Jet Printing ◽  
3D Printed

Previous studies on accuracy of three-dimensional (3D) printed model focused on full arch measurements at few points. The aim of this study was to examine the dimensional accuracy of 3D-printed models which were teeth-prepped for three-unit fixed prostheses, especially at margin and proximal contact areas. The prepped dental model was scanned with a desktop scanner. Using this reference file, test models were fabricated by digital light processing (DLP), Multi-Jet printing (MJP), and stereo-lithography apparatus (SLA) techniques. We calculated the accuracy (trueness and precision) of 3D-printed models on 3D planes, and deviations of each measured points at buccolingual and mesiodistal planes. We also analyzed the surface roughness of resin printed models. For overall 3D analysis, MJP showed significantly higher accuracy (trueness) than DLP and SLA techniques; however, there was not any statistically significant difference on precision. For deviations on margins of molar tooth and distance to proximal contact, MJP showed significantly accurate results; however, for a premolar tooth, there was no significant difference between the groups. 3D color maps of printed models showed contraction buccolingually, and surface roughness of the models fabricated by MJP technique was observed as the lowest. The accuracy of the 3D-printed resin models by DLP, MJP, and SLA techniques showed a clinically acceptable range to use as a working model for manufacturing dental prostheses

scholarly journals On the Post-Processing of 3D-Printed ABS Parts

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1559
Author(s):  
Mohammad Reza Khosravani ◽  
Jonas Schüürmann ◽  
Filippo Berto ◽  
Tamara Reinicke
Keyword(s):  
Surface Treatment ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Tests ◽  
Fracture Load ◽  
Post Processing ◽  
Fused Deposition ◽  
Dog Bone ◽  
3D Printed

Application of Additive Manufacturing (AM) has significantly increased in the past few years. AM also known as three-dimensional (3D) printing has been currently used in fabrication of prototypes and end-use products. Considering the new applications of additively manufactured components, it is necessary to study structural details of these parts. In the current study, influence of a post-processing on the mechanical properties of 3D-printed parts has been investigated. To this aim, Acrylonitrile Butadiene Styrene (ABS) material was used to produce test coupons based on the Fused Deposition Modeling (FDM) process. More in deep, a device was designed and fabricated to fix imperfection and provide smooth surfaces on the 3D-printed ABS specimens. Later, original and treated specimens were subjected to a series of tensile loads, three-point bending tests, and water absorption tests. The experimental tests indicated fracture load in untreated dog-bone shaped specimen was 2026.1 N which was decreased to 1951.7 N after surface treatment. Moreover, the performed surface treatment was lead and decrease in tensile strength from 29.37 MPa to 26.25 MPa. Comparison of the results confirmed effects of the surface modification on the fracture toughness of the examined semi-circular bending components. Moreover, a 3D laser microscope was used for visual investigation of the specimens. The documented results are beneficial for next designs and optimization of finishing processes.

scholarly journals Influence of the Infill Geometry of 3D-Printed Tablets on Drug Dissolution

2021 ◽  
Vol 5 (1) ◽  
pp. 15
Author(s):  
Nuno Venâncio ◽  
Gabriela G. Pereira ◽  
João F. Pinto ◽  
Ana I. Fernandes
Keyword(s):  
Three Dimensional ◽  
Drug Dissolution ◽  
Fused Deposition Modelling ◽  
Three Dimensional Printing ◽  
Preliminary Results ◽  
Fused Deposition ◽  
3D Printed ◽  
Dimensional Printing ◽  
Hot Melt ◽  
Patient Centric

Patient-centric therapy is especially important in pediatrics and may be attained by three-dimensional printing. Filaments containing 30% w/w of theophylline were produced by hot-melt extrusion and printed using fused deposition modelling to produce tablets. Here, preliminary results evaluating the effect of infill geometry (cross, star, grid) on drug content and release are reported.

scholarly journals Synthesis of Three-Dimensional Fe3O4/Graphene Aerogels for the Removal of Arsenic Ions from Water

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Yan Ye ◽  
Da Yin ◽  
Bin Wang ◽  
Qingwen Zhang
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
3D Structure ◽  
Three Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Aerogels ◽  
Transmission Electron ◽  
Potential Applications ◽  
Removal Of Arsenic

We report the synthesis of three-dimensional Fe3O4/graphene aerogels (GAs) and their application for the removal of arsenic (As) ions from water. The morphology and properties of Fe3O4/GAs have been characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and superconducting quantum inference device. The 3D nanostructure shows that iron oxide nanoparticles are decorated on graphene with an interconnected network structure. It is found that Fe3O4/GAs own a capacity of As(V) ions adsorption up to 40.048 mg/g due to their remarkable 3D structure and existence of magnetic Fe3O4nanoparticles for separation. The adsorption isotherm matches well with the Langmuir model and kinetic analysis suggests that the adsorption process is pseudo-second-ordered. In addition to the excellent adsorption capability, Fe3O4/GAs can be easily and effectively separated from water, indicating potential applications in water treatment.

Sign in / Sign up

Export Citation Format

Share Document