Performance and Emissions Characteristics of Diesel Engine Fuelled by Biodiesel Derived from Palm Oil

2013 ◽  
Vol 315 ◽  
pp. 517-522 ◽  
Author(s):  
Amir Khalid ◽  
Shahrul Azmir Osman ◽  
M. Norrizam Mohamad Jaat ◽  
Norrizal Mustaffa ◽  
Siti Mariam Basharie ◽  
...  
Keyword(s):  
Palm Oil ◽  
Engine Speed ◽  
Oxidation Stability ◽  
Combustion Process ◽  
Engine Performance ◽  
Load Test ◽  
Emission Regulations ◽  
Oxygenated Fuel ◽  
Performance And Emissions ◽  
Hc Emissions

Bio fuels based on vegetable oils offer the advantage being a sustainable, annually renewable source of automobile fuel. Despite years of improvement attempts, the key issue in using vegetable oil-based fuels is oxidation stability, stoichiometric point, bio-fuel composition, antioxidants on the degradation and much oxygen with comparing to diesel gas oil. Thus, the improvement of emissions exhausted from diesel engines fueled by biodiesel derived from palm oil is urgently required to meet the future stringent emission regulations. Purpose of this study is to explore how significant the effects of palm oil blending ratio on combustion process that strongly affects the vehicles performance and exhaust emissions. The engine speed was varied from 15003000 rpm, load test condition varied by Dynapack chassis dynamometer from 050% and palm oil blending ratio from 515vol% (B5B15). Increased blends of biodiesel ratio is found to enhance the combustion process, resulting in decreased the HC emissions with nearly equal of engine performance. The improvement of combustion process is expected to be strongly influenced by oxygenated fuel in biodiesel content.

scholarly journals Effects of Fuel Additive on Performance and Emissions Characteristics of Diesel Engine Fuelled by Biodiesel Derived from Palm Oil

2015 ◽  
Vol 773-774 ◽  
pp. 491-495 ◽  
Author(s):  
Amir Khalid ◽  
Azmi Abas
Keyword(s):  
Palm Oil ◽  
Diesel Fuel ◽  
Engine Speed ◽  
Combustion Process ◽  
Engine Performance ◽  
Load Test ◽  
Fuel Additive ◽  
Animal Fats ◽  
Oxygenated Fuel ◽  
Performance And Emissions

Biodiesel is the alternate fuel which is derived from renewable sources either is vegetable oils or animal fats. Biodiesel is non-toxic, have higher biodegradability, free of sulphur, no aromatics and its oxygen content of about 10-11% which is usually not contained in diesel fuel. These characteristics thus predominantly influences to the emissions of carbon monoxide (CO) and hydrocarbons (HC) in the exhaust gas. Purpose of this study is to investigate the effects of fuel additive, oil palm blended fuel, engine speed and test load conditions on the exhaust emissions and engine performance. The engine speed was varied from 1500 to 3000 rpm, load test condition varied by dynapack chassis dynamometer in 0, 50 and 100% and blends of 5(B5), 10(B10) and 15vol%(B15) palm oil with the diesel fuel. Increased of blends ratio with same mixing booster quantity can improve the engine performance, combustion process and give less CO emission. However, this condition tends to produce high NOx production due to higher oxygenated fuel in biodiesel content.

Effects of Biodiesel on Performance and Emissions Characteristics in Diesel Engine

2014 ◽  
Vol 663 ◽  
pp. 39-43
Author(s):  
Amir Khalid ◽  
M. Jaat ◽  
Norrizal Mustaffa ◽  
M.D. Anuar ◽  
B. Manshoor ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Engine Speed ◽  
Combustion Process ◽  
Engine Performance ◽  
Load Test ◽  
Test Load ◽  
Animal Fats ◽  
Oxygenated Fuel ◽  
Performance And Emissions ◽  
Blended Fuel

Biodiesel is the alternate fuel which is derived from renewable sources either is vegetable oils or animal fats. Biodiesel is non-toxic, have higher biodegradability, free of sulphur, no aromatics and its oxygen content of about 10-11% which is usually not contained in diesel fuel. These characteristics thus predominantly influences to the emissions of carbon monoxide (CO) and hydrocarbons (HC) in the exhaust gas. Purpose of this study is to investigate the effects of oil palm blended fuel, engine speed and test load conditions on the fuel properties, combustion process, combustion characteristics, exhaust emissions and engine performance. The engine speed was varied from 1500 to 3000 rpm, load test condition varied by dynapack chassis dynamometer in 0% ,50% and 100% and blends of 5 (B5), 10 (B10) and 15 vol% (B15) palm oil with the diesel fuel. Increased of blends ratio can improve the combustion process and give less HC and CO emission and almost nearly engine performance. However, this condition tends to produce high NOx production due to higher oxygenated fuel in biodiesel content.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

Experimental Investigation of Emissions Characteristics of Small Diesel Engine Fuelled by Blended Crude Palm Oil

2014 ◽  
Vol 660 ◽  
pp. 462-467
Author(s):  
Amir Khalid ◽  
M.D. Anuar ◽  
Azwan Sapit ◽  
Azahari Razali ◽  
Bukhari Manshoor ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Palm Oil ◽  
Oxidation Stability ◽  
Combustion Process ◽  
High Viscosity ◽  
Exhaust Emission ◽  
Crude Palm Oil ◽  
Performance And Emission ◽  
Emission Parameter ◽  
Oxygenated Fuel

Biodiesel is an alternative, decomposable and biological-processed fuel that has similar characteristics with mineral diesel which can be used directly into diesel engines. Crude palm oil (CPO) is one of the vegetable oil that has potential for use as a fuel in diesel engine. However, Biodiesel is also an oxygenated fuel and more density, viscosity meaning it contains influences the emissions production during burning process. Despite years of improvement attempts, the key issue in using crude palm oil fuels is oxidation stability, high viscosity and much oxygen comparing to diesel fuel. Thus, the improvement of performance and emission exhausted from biodiesel fuels is urgently required to meet the future performance and emission regulations. Purpose of this study is to explore how significant the effect of biodiesel blends on the exhaust emission with different speed. The engine speed was varied from 1500-2500 rpm and CPO blending ratio from 5-15 vol% (B5-B15).The emission parameter have been tested in term of opacity, hydrocarbon (HC), nitrogen oxide (NOX), carbon dioxide (CO2 ) and oxygen (O2). Increased blends of biodiesel ratio is found to enhance the combustion process, resulting in decreased the HC emissions and also other exhaust emission element. The improvement of combustion process is expected to be strongly influenced by oxygenated fuel in biodiesel content.

scholarly journals Jet A and Propane gas combustion in a turboshaft engine: performance and emissions reductions

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Ali Hasan ◽  
Oskar J. Haidn
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Emissions Reductions ◽  
Gas Combustion ◽  
Liquid Petroleum Gas ◽  
Performance And Emissions ◽  
Air Mixing ◽  
Turboshaft Engine ◽  
Engine Performance And Emissions ◽  
Lower Carbon

AbstractThe Paris Agreement has highlighted the need in reducing carbon emissions. Attempts in using lower carbon fuels such as Propane gas have seen limited success, mainly due to liquid petroleum gas tanks structural/size limitations. A compromised solution is presented, by combusting Jet A fuel with a small fraction of Propane gas. Propane gas with its relatively faster overall igniting time, expedites the combustion process. Computational fluid dynamics software was used to demonstrate this solution, with results validated against physical engine data. Jet A fuel was combusted with different Propane gas dosing fractions. Results demonstrated that depending on specific propane gas dosing fractions emission reductions in ppm are; NOx from 84 to 41, CO2 from less than 18,372 to less than 15,865, escaping unburned fuels dropped from 11.4 (just Jet A) to 6.26e-2 (with a 0.2 fraction of Propane gas). Soot and CO increased, this is due to current combustion chamber air mixing design.

scholarly journals Combustion Conduct Of A Single-Cylinder Spark-Ignition Affected By Ethanol Fuel Mixtures of Supplement Hydroxy Gas (HHO)

2021 ◽  
Vol 14 (2) ◽  
pp. 125-129
Author(s):  
Gatot Setyono ◽  
Navik Kholili
Keyword(s):  
Fossil Fuels ◽  
Engine Speed ◽  
Performance Test ◽  
Fuel Injection ◽  
Automatic Transmission ◽  
Combustion Process ◽  
Engine Performance ◽  
Calorific Value ◽  
Spark Ignition ◽  
Fuel Mixtures

Ethanol is an alternative fuel to replace fossil fuels. Ethanol's high octane value can substitute for power in spark-ignition engines (SI). Gasoline mixed with ethanol will reduce the calorific value generated and intensify the combustion process in the combustion chamber. Through the engine performance test, we can find out the increase in the performance of the SI engine. Several essential variables can improve engine performance, such as gasoline-ethanol variations, iridium spark plugs, and hydroxy gas generators (HHO). This research uses an experimental method by utilizing gasoline (octane-92)-ethanol variations (35%, 45%, and 55% v/v) with the intake of hydroxy gas during the combustion process. The SI automatic transmission engine has a capacity of 124.8 cubic centimeters (one cylinder-four stroke), a compression ratio of 11/1, fuel injection, and iridium spark plugs. Engine performance test using chassis dyno test with engine speed variations of 4000-9000 rpm. This study resulted in optimal performance on a 55% increase in gasoline-ethanol mixture with an intensify in output-power, pressure, and thermal efficiency at an engine-speed of 8000 rpm. It is contrary to the specific fuel consumption has decreased.

Engine Performance and Emissions for a Heavy-Duty Diesel Engine Converted to Stoichiometric Natural Gas Operation

2020 ◽  
Author(s):  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Catalytic Converter ◽  
Combustion Process ◽  
Engine Performance ◽  
Intake Manifold ◽  
Heavy Duty ◽  
Indicated Mean Effective Pressure ◽  
Performance And Emissions ◽  
Heavy Duty Diesel ◽  
Ci Engines

Abstract Converting existing compression ignition (CI) engines to spark ignition (SI) operation can increase the use of natural gas (NG) in heavy-duty engine applications and reduce the reliance on petroleum fuels. Gas fumigation upstream of the intake manifold and the addition of a spark plug in place of the diesel injector to initiate and control the combustion process is a convenient approach for converting existing diesel engines to dedicated NG operation. Stoichiometric operation and a three-way catalytic converter can help the engine to comply with increasingly strict emission regulations. However, as the CI-to-SI conversion usually maintains the conventional geometry of a CI engine (i.e., maintains the flat cylinder head and the bowl-in piston), the goal of this study was to observe some of the effects that the diesel conversion to stoichiometric NG SI operation will have on the engine’s performance and emissions. Dynamometer tests were performed at a constant engine speed at 1300 rpm but various spark timings. The experimental results for a net indicated mean effective pressure ∼ 6.7 bar showed that ignition timing did not affect the end of combustion due to the slow-burn inside the squish. Moreover, the less-optimal conditions inside the squish led to increased carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. While the combustion event was stable with no signs of knocking at the medium load conditions investigated here, the results suggest that the engine control needs to optimize the mass fraction trapped inside the squish region for a higher efficiency and lower emissions.

Effects of the Re-Entrant Bowl Geometry on a DI Turbocharged Diesel Engine Performance and Emissions—A CFD Approach

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
S. Pasupathy Venkateswaran ◽  
G. Nagarajan
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Combustion Process ◽  
Engine Performance ◽  
Maximum Diameter ◽  
Diffusion Combustion ◽  
Turbocharged Diesel Engine ◽  
Performance And Emissions ◽  
Di Diesel Engine ◽  
Fuel Mixing

The purpose of this study is to investigate the influence of re-entrant bowl geometry on both engine performance and combustion efficiency in a direct injection (DI), turbocharged diesel engine for heavy-duty applications. The piston bowl design is one of the most important factors that affect the air–fuel mixing and the subsequent combustion and pollutant formation processes in a DI diesel engine. The bowl geometry and dimensions, such as the pip region, bowl lip area, and toroidal radius, are all known to have an effect on the in-cylinder mixing and combustion processes. Based on the idea of enhancing diffusion combustion at the later stage of the combustion period, three different bowl geometries, namely, bowl 1 (baseline), bowl 2, and bowl 3 were selected and investigated. All the other relevant parameters, namely, compression ratio, maximum diameter of the bowl, squish clearance and injection rate were kept constant. A commercial CFD code STAR-CD was used to model the in-cylinder flows and combustion process, and experimental results of the baseline bowl were used to validate the numerical model. The simulation results show that, bowl 3 enhance the turbulence and hence results in better air-fuel mixing among all three bowls in a DI diesel engine. As a result, the indicated specific fuel consumption and soot emission reduced although the NOx emission is increased owing to better mixing and a faster combustion process. Globally, since the reduction in soot is larger (−46% as regards baseline) than the increase in NOx (+15% as regards baseline), it can be concluded that bowl 3 is the best trade-off between performance and emissions.

Investigation of Engine Performance and Emission Characteristics of Si Engine Fuelled with Ethanol Blends by Numerical Simulation

2014 ◽  
Vol 1016 ◽  
pp. 597-601
Author(s):  
Ceyla Ozgur ◽  
Erdi Tosun ◽  
Tayfun Ozgur ◽  
Gökhan Tuccar ◽  
Kadi̇r Aydin
Keyword(s):  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition Engine ◽  
Emission Characteristics ◽  
Si Engine ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Ethanol Addition ◽  
Ethanol Blends ◽  
Engine Performance And Emissions

In this study the influences of ethanol addition to gasoline on an spark ignition engine performance and emissions were explored. AVL BOOST software was used to simulate the performance and emission characteristics of different ethanol-gasoline blends. The blended fuels contain 5%, 10% and 15% of ethanol by volume, and indicated as B95E5, B90E10, and B85E15, respectively. The results showed that ethanol addition to gasoline fuel improve combustion process, decrease CO emissions and reduce BSFC of the SI engine.

Wear, Performance and Emissions of a Two-Stroke Engine Running on Palm Oil Methyl Ester Blended Lubricant

1996 ◽  
Vol 210 (4) ◽  
pp. 213-219 ◽  
Author(s):  
H H Masjuki ◽  
M A Maleque
Keyword(s):  
Methyl Ester ◽  
Palm Oil ◽  
Gasoline Engine ◽  
Engine Performance ◽  
Lubricating Oil ◽  
Wear Behaviour ◽  
Exhaust Gas ◽  
Piston Rings ◽  
Gasoline Engines ◽  
Performance And Emissions

Results of study on wear of piston rings, engine performance and exhaust gas emissions of palm oil methyl ester (POME) as a lubricating oil additive in a two-stroke gasoline engine test are presented. Piston ring wear behaviour was monitored as a function of running time. The power output and brake specific fuel consumption of the engine were measured at different speeds. Varnish/lacquer and carbon deposit on the spark plug electrode, cylinder and piston heads as well as exhaust gas (CO2, CO and O2) emission were measured. For comparison purposes, two types of commercial lubricating oils, viz. oil A and oil B were used. The wear resistance of piston rings with POME blending lubrication was found to be greater than the pure commercial oil lubrication. Other results indicate that the POME acts as an additive which improves the engine performance and exhaust emissions of two-stroke gasoline engines.

Sign in / Sign up

Export Citation Format

Share Document