scholarly journals Parametric Knocking Performance Investigation of Spark Ignition Natural Gas Engines and Dual Fuel Engines

2020 ◽  
Vol 8 (6) ◽  
pp. 459 ◽  
Author(s):  
La Xiang ◽  
Gerasimos Theotokatos ◽  
Haining Cui ◽  
Keda Xu ◽  
Hongkai Ben ◽  
...  
Keyword(s):  
Natural Gas ◽  
Compression Ratio ◽  
Engine Performance ◽  
Spark Ignition ◽  
Combustion Model ◽  
Dual Fuel ◽  
Ignition Timing ◽  
Natural Gas Engines ◽  
Study Results ◽  
Pilot Fuel

Both spark ignition (SI) natural gas engines and compression ignition (CI) dual fuel (DF) engines suffer from knocking when the unburnt mixture ignites spontaneously prior to the flame front arrival. In this study, a parametric investigation is performed on the knocking performance of these two engine types by using the GT-Power software. An SI natural gas engine and a DF engine are modelled by employing a two-zone zero-dimensional combustion model, which uses Wiebe function to determine the combustion rate and provides adequate prediction of the unburnt zone temperature, which is crucial for the knocking prediction. The developed models are validated against experimentally measured parameters and are subsequently used for performing parametric investigations. The derived results are analysed to quantify the effect of the compression ratio, air-fuel equivalence ratio and ignition timing on both engines as well as the effect of pilot fuel energy proportion on the DF engine. The results demonstrate that the compression ratio of the investigated SI and DF engines must be limited to 11 and 16.5, respectively, for avoiding knocking occurrence. The ignition timing for the SI and the DF engines must be controlled after −38°CA and 3°CA, respectively. A higher pilot fuel energy proportion between 5% and 15% results in increasing the knocking tendency and intensity for the DF Engine at high loads. This study results in better insights on the impacts of the investigated engine design and operating settings for natural gas (NG)-fuelled engines, thus it can provide useful support for obtaining the optimal settings targeting a desired combustion behaviour and engine performance while attenuating the knocking tendency.

scholarly journals Numerical Study of Engine Performance and Emissions for Port Injection of Ammonia into a Gasoline\Ethanol Dual-Fuel Spark Ignition Engine

2021 ◽  
Vol 11 (4) ◽  
pp. 1441
Author(s):  
Farhad Salek ◽  
Meisam Babaie ◽  
Amin Shakeri ◽  
Seyed Vahid Hosseini ◽  
Timothy Bodisco ◽  
...  
Keyword(s):  
Numerical Study ◽  
Combustion Process ◽  
Engine Performance ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Combustion Model ◽  
Dual Fuel ◽  
Spark Ignition Engines ◽  
Performance And Emissions ◽  
Hc Emissions

This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.

scholarly journals Implementation and Parameter Analysis of the Knock Phenomenon of a Marine Dual-Fuel Engine Based on a Two-Zone Combustion Model

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 602
Author(s):  
Fang-Kun Zou ◽  
Hong Zeng ◽  
Huai-Yu Wang ◽  
Xin-Xin Wang ◽  
Zhao-Xin Xu
Keyword(s):  
Natural Gas ◽  
Air Temperature ◽  
Compression Ratio ◽  
Operating Parameter ◽  
Parameter Analysis ◽  
Combustion Model ◽  
Dual Fuel ◽  
Inlet Temperature ◽  
Dimensional Model ◽  
Engine Knock

The stable working window of a dual-fuel engine is narrow, and it is prone to knock during operation. The occurrence of knock limits the load and torque output of a dual-fuel engine, and even causes engine damage in severe cases. The existing volumetric model of marine dual-fuel engine has little research on the related problems of knock simulation. In order to analyze the causes of knock phenomenon and the influence of operating parameter changes on knock, under the Matlab/Simulink simulation environment, a quasi-dimensional model was established with MAN 8L51/60DF dual-fuel engine as the prototype, and the model was calibrated using the bench data. The knock intensity index coefficient (KI) was used as the evaluation index of knock intensity. Three parameters, the intake air temperature, compression ratio, and natural gas intake, were selected as variables to simulate the engine. According to the analysis of the simulation results, the influence of the parameter changes on the occurrence of engine knock phenomenon and knock intensity could be further studied. The results showed that the combination of the KI model and the quasi-dimensional model could effectively and accurately predict the engine performance and knock trend. The change of gas inlet quality, compression ratio, and inlet temperature could promote the occurrence of detonation, the engine knock could be avoided by controlling the intake air temperature below 336 K, compression ratio not exceeding 15 or the intake volume of natural gas per cycle not exceeding 11.25 g/cycle.

To Study the Effects of (Compressed Natural Gas + Diesel) Under Dual Fuel Mode on Engine Performance and Emissions Characteristic

2020 ◽  
Vol 18 (2) ◽  
pp. 108-112
Author(s):  
Ashok Kumar ◽  
Piyushi Nautiyal ◽  
Kamalasish Dev
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Engine Performance ◽  
Experimental Results ◽  
Dual Fuel ◽  
Compressed Natural Gas ◽  
Performance And Emissions ◽  
Pilot Fuel ◽  
Energy Share ◽  
Engine Performance And Emissions

The present study is investigated on the performance and emissions characteristics of a diesel engine fuelled by compressed natural gas and base diesel (CNG + Diesel). The CNG fuels used as the primary fuel, and diesel as pilot fuel under dual-fuel mode. The pilot fuel is partially replaced by CNG at a different percentage. The primary fuel is injected into the engine with intake air during the suction stroke. The experimental results reveal the effect of CNG + diesel under dual fuel mode on BTE, BSFC, CO, CO2, HC, NOx and Smoke. It is observed from the experimental results that CO2, NOx and Smoke emissions decreased but HC and CO emissions increase with an increase in CNG energy share.

Numerical and Experimental Investigation on Performance of Dual Fuel D87 Engine

2010 ◽  
Author(s):  
A. Gharehghani ◽  
A. Jazayeri ◽  
M. Mirsalim ◽  
M. Ghanbari
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Engine Performance ◽  
Diesel Oil ◽  
Combustion Characteristic ◽  
Combustion Model ◽  
Dual Fuel ◽  
Detailed Chemical Kinetics ◽  
Mode Of Operation ◽  
Cheap Alternative

Conventional compression ignition internal combustion engines can easily be converted to a dual fuel mode of operation using natural gas as the main fuel and diesel oil injection as pilot to initiate the mixture or as a part of main fuel to improve the power output by changing the percentage of diesel oil to natural gas. Natural gas is abundant and relatively cheap alternative fuel with capability of reducing emission levels considerably. In order to examine the combustion characteristic of a heavy duty diesel engine which is locally produced, called D87, in dual fuel mode of operation. A detail performance analysis has been carried out where the main fuel is natural gas and diesel oil is as pilot injection. A reduced detailed chemical kinetics combustion model is combined with a partially stirred combustion model which is inserted in KIVA3V2 code to predict the knock and performance characteristics of the engine. Also, interaction between fuels during the combustion has been studied. Influence of parameters such as intake pressure and temperature on occurrence of knock and the effect of initial swirl ratio on engine performance parameters such in cylinder heat release rate, temperature-pressure and emission levels have been investigated. Appropriate computational grid for KIVA has been generated by ANSYS ICEM CFD commercial software. The developed model results are compared and validated with experimental results available during development tests.

Comparative Evaluation of the Effect of Intake Charge Temperature, Pilot Fuel Quantity and Injection Advance on Dual Fuel Compression Ignition Engine Performance Characteristics and Emitted Pollutants

2009 ◽  
Author(s):  
Roussos G. Papagiannakis ◽  
Theodoros C. Zannis ◽  
Elias A. Yfantis ◽  
Dimitrios T. Hountalas
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
High Speed ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Performance Characteristics ◽  
Dual Fuel ◽  
Pilot Fuel

The simultaneous reduction of nitrogen oxide emissions and particulate matter in a compression ignition environment is quite difficult due to the soot/NOx trade off and it is often accompanied by fuel consumption penalties. Thus, fuel reformulation is also essential for the curtailment of diesel pollutant emissions along with the optimization of combustion-related design factors and exhaust after-treatment equipment. Various solutions have been proposed for improving the combustion process of conventional diesel engines and reducing the exhaust emissions without making serious modifications on the engine, one of which is the use of natural gas as a supplement for the conventional diesel fuel (Dual Fuel Natural Gas/Diesel Engines). Natural gas is considered to be quite promising since its cost is relative lower compared to conventional fuels and it has high auto-ignition temperature compared to other gaseous fuels facilitating thus its use on future and existing fleet of small high speed direct injection diesel engines without serious modifications on their structure. Moreover, natural gas does not generate particulates when burned in engines. The most common natural gas/diesel operating mode is referred to as the Pilot Ignited Natural Gas Diesel Engine (P.I.N.G.D.E). Here, the primary fuel is natural gas that controls the engine power output, while the pilot diesel fuel injected near the end of the compression stroke autoignites and creates ignition sources for the surrounding gaseous fuel mixture to be burned. Previous research studies have shown that the main disadvantage of this dual fuel combustion is its negative impact on engine efficiency compared to the normal diesel operation, while carbon monoxide emissions are also increased. The specific engine operating mode, in comparison with conventional diesel fuel operation, suffers from low brake engine efficiency and high carbon monoxide (CO) emissions. The influence becomes more evident at part load conditions. Intake charge temperature, pilot fuel quantity and injection advance are some of the engine parameters which influence significantly the combustion mechanism inside the combustion chamber of a Pilot Ignited Natural Gas Diesel Engine. In order to be examined the effect of these parameters on performance and exhaust emissions of a natural gas/diesel engine a theoretical investigation has been conducted by using a numerical simulation. In order to be examined the effect of increased air inlet temperature combined with increased pilot fuel quantity and its injection timing on performance and exhaust emissions of a pilot ignited natural gas-diesel engine, a theoretical investigation has been conducted by using a comprehensive two-zone phenomenological model. The results concerning engine performance characteristics and NO, CO and Soot emissions for various engine operating conditions (i.e. load and engine speed), comes from the employment of a comprehensive two-zone phenomenological model which had been applied on a high-speed natural gas/diesel engine. The main objectives of this comparative assessment are to record and to comparatively evaluate the relative impact each one of the above mentioned parameters on engine performance characteristics and emitted pollutants. Furthermore, the present investigation deals with the determining of optimum combinations between the parameters referred before since at high engine load conditions, the simultaneous increase some of the specific parameters may lead in undesirable results about engine performance characteristics. The conclusions of the specific investigation will be extremely valuable for the application of this technology on existing DI diesel engines.

Effects of Natural Gas Compositions on Engine In-Cylinder Process

2015 ◽  
Vol 1092-1093 ◽  
pp. 498-503
Author(s):  
La Xiang ◽  
Yu Ding
Keyword(s):  
Natural Gas ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Engine Performance ◽  
Maximum Temperature ◽  
Maximum Pressure ◽  
Test Bed ◽  
Promising Alternative ◽  
Natural Gas Engines ◽  
Lower Maximum

Natural gas (NG) is one of the most promising alternative fuels of diesel and petrol because of its economics and environmental protection. Generally the NG engine share the similar structure profile with diesel or petrol engine but the combustion characteristics of NG is varied from the fuels, so the investigation of NG engine combustion process receive more attentions from the researchers. In this paper, a zero-dimensional model on the basis of Vibe function is built in the MATLAB/SIMULINK environment. The model provides the prediction of combustion process in natural gas engines, which has been verified by the experimental data in the NG test bed. Furthermore, the influence of NG composition on engine performance is investigated, in which the in-cylinder maximum pressure and temperature and mean indicated pressure are compared using different type NG. It is shown in the results that NG with higher composition of methane results in lower maximum temperature and mean indicated pressure as well as higher maximum pressure.

Performance of Dual Fuel Engine Running on Jojoba Oil as Pilot Fuel and CNG or LPG

2007 ◽  
Author(s):  
Mohamed Y. E. Selim ◽  
M. S. Radwan ◽  
H. E. Saleh
Keyword(s):  
Methyl Ester ◽  
Natural Gas ◽  
Pressure Rise ◽  
Combustion Noise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Pilot Fuel

The use of Jojoba Methyl Ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or LPG at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or liquefied petroleum gas (LPG) as the main fuel and Jojoba Methyl Ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic data of 100 engine cycle in terms of maximum pressure and its pressure rise rate. The tests examined the following engine parameters: gaseous fuel type, engine speed and load, pilot fuel injection timing, pilot fuel mass and compression ratio. Results showed that using the Jojoba fuel with its improved properties has improved the dual fuel engine performance, reduced the combustion noise, extended knocking limits and reduced the cyclic variability of the combustion.

Evaluation of Spark Plug and Timing Configurations on the Fuel Consumption, Combustion Stability, and Emissions of a Large-Bore, Two-Stroke, Natural Gas Engine

2016 ◽  
Author(s):  
Derek Johnson ◽  
Marc Besch ◽  
Nathaniel Fowler ◽  
Robert Heltzel ◽  
April Covington
Keyword(s):  
Natural Gas ◽  
Fuel Consumption ◽  
Combustion Engine ◽  
Engine Performance ◽  
Combustion Stability ◽  
Oxides Of Nitrogen ◽  
Natural Gas Engines ◽  
Fuel Delivery ◽  
Spark Plug ◽  
Trade Offs

Emissions compliance is a driving factor for internal combustion engine research pertaining to both new and old technologies. New standards and compliance requirements for off-road spark ignited engines are currently under review and include greenhouse gases. To continue operation of legacy natural gas engines, research is required to increase or maintain engine efficiency, while reducing emissions of carbon monoxide, oxides of nitrogen, and volatile organic compounds such as formaldehyde. A variety of technologies can be found on legacy, large-bore natural gas engines that allow them to meet current emissions standards — these include exhaust after-treatment, advanced ignition technologies, and fuel delivery methods. The natural gas industry uses a variety of spark plugs and tuning methods to improve engine performance or decrease emissions of existing engines. The focus of this study was to examine the effects of various spark plug configurations along with spark timing to examine any potential benefits. Spark plugs with varied electrode diameter, number of ground electrodes, and heat ranges were evaluated against efficiency and exhaust emissions. Combustion analyses were also conducted to examine peak firing pressure, location of peak firing pressure, and indicated mean effective pressure. The test platform was an AJAX-E42 engine. The engine has a bore and stroke of 0.216 × 0.254 meters (m), respectively. The engine displacement was 9.29 liters (L) with a compression ratio of 6:1. The engine was modified to include electronic spark plug timing capabilities along with a mass flow controller to ensure accurate fuel delivery. Each spark plug configuration was examined at ignition timings of 17, 14, 11, 8, and 5 crank angle degrees before top dead center. The various configurations were examined to identify optimal conditions for each plug comparing trade-offs among brake specific fuel consumption, oxides of nitrogen, methane, formaldehyde, and combustion stability.

Sign in / Sign up

Export Citation Format

Share Document