scholarly journals Power Prediction of Bifacial Si PV Module with Different Reflection Conditions on Rooftop

2018 ◽  
Vol 8 (10) ◽  
pp. 1752 ◽  
Author(s):  
Hae Cha ◽  
Byeong Bhang ◽  
So Park ◽  
Jin Choi ◽  
Hyung Ahn
Keyword(s):  
High Performance ◽  
Measurement Data ◽  
Positive Influence ◽  
Performance Ratio ◽  
Photovoltaic Module ◽  
Rear Side ◽  
Module Structure ◽  
Power Prediction ◽  
Solar Module ◽  
Pv Module

A bifacial solar module has a structure that allows the rear electrode to be added to the existing silicon photovoltaic module structure. Thus, it can capture energy from both the front and rear sides of the module. In this paper, modeling is suggested to estimate the amount of energy generated from the rear of the bifacial photovoltaic module. After calculating the amount of irradiance from the rear side, the estimated power generation is compared with the real power output from the rear side of the module. The experiments were performed using four different environments with different albedos. The theoretical prediction of the model shows a maximum of 5% and average of 1.86% error in the measurement data. Based on the nature of the bifacial solar module, which receives additional irradiance from the rear side, this study compared the output amounts with respect to different rear environments. Recently, installation of floating Photovoltaic has been increasing. As the reflection of irradiation from the water surface occurs, the positive influence of the installation with the bifacial photovoltaic can be expected. We are confident that this research will contribute to zero energy construction by designing systems based on bifacial PV module with high performance ratio when applying solar power in a microgrid environment, which is the future energy.

scholarly journals Simulation Model of PV Module Built from Point-Focusing Fresnel Radiation Concentrators and Three-Junction High-Performance Cells

2022 ◽  
Vol 12 (2) ◽  
pp. 806
Author(s):  
Mariusz T. Sarniak
Keyword(s):  
Solar Radiation ◽  
High Performance ◽  
High Efficiency ◽  
Small Deviation ◽  
Direct Solar Radiation ◽  
Photovoltaic Module ◽  
Module Structure ◽  
Efficient Design ◽  
Pv Module ◽  
Model And Simulation

The silicon photovoltaic modules that dominate the market today are constantly being modified, but at the same time, the search for new, more efficient design solutions is underway. The study examined a less popular photovoltaic module built from point-focusing Fresnel radiation concentrators and high-efficiency three-junction cells. The advantage of this type of module is its high overall efficiency, exceeding 30%. The disadvantage is that they require biaxial precision tracking mechanisms because even a small deviation of the direction of direct solar radiation from the perpendicular to the module’s surface causes a large and abrupt drop in efficiency. This type of photovoltaic module structure is often also marked with the symbol C3PV. A mathematical model and simulation calculations were carried out in the Matlab/Simulink package for the C3PV module—the CX-75/200 model based on the “Solar Cell” component. The concentration of direct solar radiation was taken into account. For the module under consideration, experimental and simulation results show the necessity of accurate positioning concerning the direction of solar radiation—deviation of the radiation angle by about 5° causes a very high power loss (by about 92%).

scholarly journals Effect of Solar Tilt Angles on Photovoltaic Module Performance: A Behavioral Optimization Approach

2020 ◽  
pp. 90-102
Author(s):  
Trina Som ◽  
A. Sharma ◽  
D. Thakur
Keyword(s):  
Solar Energy ◽  
Tilt Angle ◽  
Photovoltaic Module ◽  
Optimization Approach ◽  
Solar Module ◽  
Monthly Average ◽  
Pv Module ◽  
Yearly Maximum ◽  
Module Performance ◽  
Better Than

In the present study, performance analyses of a solar module are made through the optimal variation of solar tilt angle, pertaining to the maximum generation of solar energy. The work has been carried out for a particular location at Tripura, in India, considering three different cases on an annual basis. An intelligent behavioural based algorithm, known as artificial bee algorithm (ABC), has been implemented for finding the optimal orientation of solar angle in analysing the performance. The result shows marginal differences are obtained in producing yearly maximum solar energy for different orientations of the PV module. It has been observed that the maximum average solar energy is obtained for the case where continuous adjustment is made by rotating the plane about the horizontal east-west axis within 20° to 30° tilt angle. The computed maximum and minimum of the monthly average efficiency is 10.9% and 8.7%, respectively. Further, a comparative study has been performed in generating average solar energy through optimal tilt angle by the implementation of Perturb & Observe method (P&O). The monthly average solar power computed by P&O method resulted better in a range of 2% to 15% in comparison to that obtained by ABC. While on the other hand, the efficiency computed by ABC algorithm was 15% to 19% better than that evaluated by P&O method for all the cases studied in the present work.

scholarly journals Impacts of Cloud Cover and Dust on the Performance of Photovoltaic Module in Niamey

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Abdoulatif Bonkaney ◽  
Saïdou Madougou ◽  
Rabani Adamou
Keyword(s):  
Cloud Cover ◽  
Photovoltaic Module ◽  
Energy Yield ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module ◽  
Long Term Effect ◽  
Daily Energy ◽  
Dust Accumulation

The sensitivity of monocrystalline solar module towards dust accumulation and cloud cover is investigated from May to August 2015 for Niamey’s environment. Two solar modules with the same characteristics have been used to assess the impacts of the dust on the solar PV module. One of the modules is being cleaned every morning and the second one was used for monitoring the effect of dust accumulation onto the surface of the unclean module for May and June. Results show that dust accumulation has a great effect on decreasing the daily energy yield of the unclean module. But this effect is a long-term effect. For the cloud cover, the effect is immediate. It was estimated that exposing the module into the environment in 23 days in June 2015 has reduced the daily energy yield by 15.29%. This limitation makes solar PV an unreliable source of power for remote devices and thus strongly suggests the challenges of cleaning the module’s surface regularly.

scholarly journals An Experimental and Comparative Performance Evaluation of a Hybrid Photovoltaic-Thermoelectric System

2021 ◽  
Vol 9 ◽  
Author(s):  
Muhammad Ahsan Iqbal Khan ◽  
Muhammad Irfan Khan ◽  
Ali Hussain Kazim ◽  
Aqsa Shabir ◽  
Fahid Riaz ◽  
...  
Keyword(s):  
Output Power ◽  
Conversion Efficiency ◽  
Hybrid System ◽  
Large Scale ◽  
Total Output ◽  
Photovoltaic Module ◽  
Rear Side ◽  
Pv System ◽  
Thermoelectric Modules ◽  
Pv Module

The majority of incident solar irradiance causes thermalization in photovoltaic (PV) cells, attenuating their efficiency. In order to use solar energy on a large scale and reduce carbon emissions, their efficiency must be enhanced. Effective thermal management can be utilized to generate additional electrical power while simultaneously improving photovoltaic efficiency. In this work, an experimental model of a hybrid photovoltaic-thermoelectric generation (PV-TEG) system is developed. Ten bismuth telluride-based thermoelectric modules are attached to the rear side of a 10 W polycrystalline silicon-based photovoltaic module in order to recover and transform waste thermal energy to usable electrical energy, ultimately cooling the PV cells. The experiment was then carried out for 10 days in Lahore, Pakistan, on both a simple PV module and a hybrid PV-TEG system. The findings revealed that a hybrid system has boosted PV module output power and conversion efficiency. The operating temperature of the PV module in the hybrid system is reduced by 5.5%, from 55°C to 52°C. Due to a drop in temperature and the addition of some recovered energy by thermoelectric modules, the total output power and conversion efficiency of the system increased. The hybrid system’s cumulative output power increased by 19% from 8.78 to 10.84 W, compared to the simple PV system. Also, the efficiency of the hybrid PV-TEG system increased from 11.6 to 14%, which is an increase of 17% overall. The results of this research could provide consideration for designing commercial hybrid PV-TEG systems.

scholarly journals Characterization Performance of Monocrystalline Silicon Photovoltaic Module Using Experimentally Measured Data

2019 ◽  
Vol 25 (10) ◽  
pp. 1-19
Author(s):  
Mena Safaa Mohammed ◽  
Emad Talib Hashim
Keyword(s):  
Ambient Temperature ◽  
Solar Irradiance ◽  
Clean Energy ◽  
Monocrystalline Silicon ◽  
Solar Irradiation ◽  
Weather Data ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Solar Module ◽  
Pv Module

Solar photovoltaic (PV) system has emerged as one of the most promising technology to generate clean energy. In this work, the performance of monocrystalline silicon photovoltaic module is studied through observing the effect of necessary parameters: solar irradiation and ambient temperature. The single diode model with series resistors is selected to find the characterization of current-voltage (I-V) and power-voltage (P-V) curves by determining the values of five parameters ( ). This model shows a high accuracy in modeling the solar PV module under various weather conditions. The modeling is simulated via using MATLAB/Simulink software. The performance of the selected solar PV module is tested experimentally for different weather data (solar irradiance and ambient temperature) that is gathered from October 2017 to April 2018 in the city of Baghdad. The collected data is recorded for the entire months during the time which is limited between 8:00 AM and 1:00 PM. This work demonstrates that the change in a cell temperature is directly proportional with the PV module current, while it is inversely proportional with the PV module voltage. Additionally, the output power of a PV module increases with decreasing the solar module temperature. Furthermore, the Simulink block diagram is used to evaluate the influence of weather factors on the PV module temperature by connecting to the MATLAB code. The best value from the results of this work was in March when the solar irradiance was equal to 1000 W/m2 and the results were: Isc,exp=3.015, Isc,mod=3.25 , RE=7.79 and Voc,exp=19.67 ,Voc,mod=19.9 ,RE=1.1

scholarly journals Performance analysis of thermosyphon hybrid photovoltaic thermal collector

2016 ◽  
Vol 27 (1) ◽  
pp. 28 ◽  
Author(s):  
N. Marc-Alain Mutombo ◽  
Freddie Inambao ◽  
Glen Bright
Keyword(s):  
Solar Irradiance ◽  
Rectangular Channel ◽  
Environmental Parameters ◽  
Photovoltaic Module ◽  
The Sun ◽  
Cell Temperature ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Incoming Energy

The conversion of solar irradiance into electricity by a photovoltaic module (PV) is 6– 7% of the incoming energy from the sun depending on the type of technology and the environmental parameters. More than 80% of incoming energy from the sun is reflected or absorbed by the solar module. The fraction of energy absorbed increases with solar cell temperature and the cells’ efficiency drops as a consequence. The efficiency of a PV module is improved by combining a PV module and a thermal collector in one unit, resulting in a hybrid photovoltaic and thermal collector (PV/T). The purpose of this paper is to present the behavior a thermosyphon hybrid PV/T when exposed to variations of environmental parameters and to demonstrate the advantage of cooling photovoltaic modules with water using a rectangular channel profile for the thermal collector. A single glazed flat-box absorber PV/T module was designed, its behavior for different environmental parameters tested, the numerical model developed, and the simulation for particular days for Durban weather run. The simulation result showed that the overall efficiency of the PV/T module was 38.7% against 14.6% for a standard PV module while the water temperature in the storage tank reached 37.1 °C. This is a great encouragement to the marketing of the PV/T technology in South Africa particularly during summer, and specifically in areas where the average annual solar irradiance is more than 4.70 kWh/m²/day.

scholarly journals A New Model for Estimation of Energy Extraction from Bifacial Photovoltaic Modules

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5089
Author(s):  
Preeti Kumari Sahu ◽  
J. N. Roy ◽  
Chandan Chakraborty ◽  
Senthilarasu Sundaram
Keyword(s):  
Tilt Angle ◽  
Geographical Location ◽  
Performance Ratio ◽  
Real Field ◽  
Photovoltaic Module ◽  
Rear Side ◽  
Energy Yield ◽  
Solar Photovoltaic ◽  
The Cost ◽  
The Impact

The energy yield from bifacial solar photovoltaic (PV) systems can be enhanced by optimizing the tilt angle. Bifacial modules boost the energy yield by 4% to 15% depending on the module type and ground reflectivity with an average of 9%. The selection of tilt angle depends on several factors, including the geographical location, weather variation, etc. Compared to the variable tilt angle, a constant angle is preferred from the point of view of the cost of installation and the cost of maintenance. This paper proposes a new method for analysing bifacial modules. A simpler rear-side irradiance model is presented to estimate the energy yield of a bifacial solar photovoltaic module. The detailed analysis also explores the optimum tilt angle for the inclined south–north orientation to obtain the maximum possible yield from the module. Taking four regions into account, i.e., Kharagpur, Ahmedabad, Delhi, and Thiruvananthapuram, in the Indian climate, we studied several cases. The Kharagpur system showed a monthly rear irradiance gain of 13%, and the Delhi climate showed an average performance ratio of 19.5%. We studied the impact of albedo and GCR on the tilt angle. Finally, the estimated model was validated with the PVSyst version 6.7.6 as well as real field test measurements taken from the National Renewable Energy Laboratory (NREL) located in the USA.

scholarly journals Comparison of Performance Measurements of Photovoltaic Modules during Winter Months in Taxila, Pakistan

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Muhammad Anser Bashir ◽  
Hafiz Muhammad Ali ◽  
Shahid Khalil ◽  
Muzaffar Ali ◽  
Aysha Maryam Siddiqui
Keyword(s):  
Solar Irradiance ◽  
Strong Dependence ◽  
Performance Ratio ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Comparative Performance ◽  
Solar Module ◽  
Photovoltaic Modules ◽  
And Performance ◽  
Module Efficiency

This paper presents the comparative performance evaluation of three commercially available photovoltaic modules (monocrystalline, polycrystalline, and single junction amorphous silicon) in Taxila, Pakistan. The experimentation was carried out at outdoor conditions for winter months. Power output, module efficiency, and performance ratio were calculated for each module and the effect of module temperature and solar irradiance on these parameters was investigated. Module parameters showed strong dependence on the solar irradiance and module temperature. Monocrystalline and polycrystalline modules showed better performance in high irradiance condition whereas it decreased suddenly with decrease in irradiance. Amorphous solar module also showed good performance in low irradiance due to its better light absorbing characteristics and thus showed higher average performance ratio. Monocrystalline photovoltaic module showed higher monthly average module efficiency and was found to be more efficient at this site. Module efficiency and performance ratio showed a decreasing trend with increase of irradiance and photovoltaic module back surface temperature.

scholarly journals Thermal and electrical energy yield analysis of a directly water cooled photovoltaic module

2016 ◽  
Vol 20 (1) ◽  
pp. 155-163
Author(s):  
Busiso Mtunzi ◽  
Edson Meyer ◽  
Simon Michael
Keyword(s):  
High Performance ◽  
Electrical Power ◽  
Electrical Energy ◽  
Performance Ratio ◽  
Photovoltaic Module ◽  
Energy Yield ◽  
Photovoltaic Modules ◽  
Utility Company ◽  
Electrical Power Output ◽  
Font Color

Electrical energy of photovoltaic modules drops by 0.5% for each degree increase in temperature. Direct water cooling of photovoltaic modules was found to give improved electrical and thermal yield. A prototype was put in place to analyse the field data for a period of a year. The results showed an initial high performance ratio and electrical power output. The monthly energy saving efficiency of the directly water cooled module was found to be approximately 61%. The solar utilisation of the naturally cooled photovoltaic module was found to be 8.79% and for the directly water cooled module its solar utilisation was 47.93%. Implementation of such systems on households may reduce the load from the utility company, bring about huge savings on electricity bills and help in reducing carbon emissions. <br><br><font color="red"><b> This article has been retracted. Link to the retraction <u><a href="http://dx.doi.org/10.2298/TSCI160407082E">10.2298/TSCI160407082E</a><u></b></font>

scholarly journals TEMPERATURE AND IRRADIANCE BASED ANALYSIS THE SPECIFIC VARIATION OF PV MODULE

2021 ◽  
Vol 83 (6) ◽  
pp. 1-17
Author(s):  
Mohsin Ali Koondhar ◽  
Irfan Ali Channa ◽  
Sadullah Chandio ◽  
Muhammad Ismail Jamali ◽  
Abdul Sami Channa ◽  
...  
Keyword(s):  
Iterative Methods ◽  
Standard Test ◽  
Operating Conditions ◽  
Back Surface ◽  
Photovoltaic Module ◽  
Solar Module ◽  
Pv Module ◽  
Test Conditions ◽  
Specific Variation ◽  
Module Efficiency

The effect of irradiance and increase of temperature on the back surface of the PV module would decrease the standardized efficiency of PV. To overcome this problem observed results of solar module (ORSM) and Newton Raphson’s (iterative) methods have been proposed in this research. This article compares ORSM and iterative methods of changing the specifications of a single diode model (SDM) extracted from a PV module beneath standard test conditions (STC) to calculate irradiance and various operating conditions. To make this comparison, the exact value of each diode parameter on the STC is essential. These are achieved by accepted algebraic values and iterative techniques. Newton Raphson’s technique has been proven to be the mainly precise method to find these specifications in STC. Therefore, these specifications are used to different techniques that change the parameters of an SDM with radiation and temperature. The MATLAB model is designed to assess the conducting of individual techniques by PVM. The results are compared with the measured data, and the accuracy of photovoltaic module efficiency has been achieved through different technologies at different temperature and insolation levels.

Sign in / Sign up

Export Citation Format

Share Document