scholarly journals Effect of Mono-, Di-, and Triethylene Glycol on the Activity of Phosphate-Doped NiMo/Al2O3 Hydrotreating Catalysts

Catalysts ◽  
2019 ◽  
Vol 9 (1) ◽  
pp. 96 ◽  
Author(s):  
Alexey Nuzhdin ◽  
Galina Bukhtiyarova ◽  
Aleksander Porsin ◽  
Igor Prosvirin ◽  
Irina Deliy ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Triethylene Glycol ◽  
Sulfide Catalysts ◽  
Gas Oil ◽  
N2 Adsorption ◽  
X Ray ◽  
Transmission Electron ◽  
Al2o3 Catalyst ◽  
Impregnation Solution

The effect of glycols on the catalytic properties of phosphate-doped NiMo/Al2O3 catalysts in the hydrotreating of straight-run gas oil (SRGO) was studied. The NiMo(P)/Al2O3 catalysts were prepared using ethylene glycol (EG), diethylene glycol (DEG), and triethylene glycol (TEG) as additives. The organic agent was introduced into the aqueous impregnation solution obtained by the dissolving of MoO3 in H3PO4 solution, followed by Ni(OH)2 addition. The Raman and UV–Vis studies show that the impregnation solution contains diphosphopentamolybdate HxP2Mo5O23(6−x)− and Ni(H2O)62+, and that these ions are not affected by the presence of glycols. When the impregnation solution comes in contact with the γ-Al2O3 surface, HxP2Mo5O23(6−x)− is decomposed completely. The catalysts were characterized by Raman spectroscopy, low-temperature N2 adsorption, X-ray photoelectron spectroscopy, and transmission electron microscopy. It is shown that the sulfide catalysts prepared with glycols display higher activity in the hydrotreating of straight-run gas oil than the NiMoP/Al2O3 catalyst prepared without the additive. The hydrodesulfurization and hydrodenitrogenation activities depend on the glycol type and are decreased in the following order: NiMoP-DEG/Al2O3 > NiMoP-EG/Al2O3 > NiMoP-TEG/Al2O3 > NiMoP/Al2O3. The higher activity of NiMoP-DEG/Al2O3 can be explained with the higher dispersion of molybdenum on the surface of the catalyst in the sulfide state.

scholarly journals Surface Study of CuO Nanopetals by Advanced Nanocharacterization Techniques with Enhanced Optical and Catalytic Properties

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1298 ◽  
Author(s):  
Muhammad Arif Khan ◽  
Nafarizal Nayan ◽  
Shadiullah Shadiullah ◽  
Mohd Khairul Ahmad ◽  
Chin Fhong Soon
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Average Length ◽  
Tem Analysis ◽  
X Ray ◽  
Surface Study ◽  
Transmission Electron ◽  
One Step ◽  
Controlled Morphology ◽  
Xrd Patterns

In the present work, a facile one-step hydrothermal synthesis of well-defined stabilized CuO nanopetals and its surface study by advanced nanocharacterization techniques for enhanced optical and catalytic properties has been investigated. Characterization by Transmission electron microscopy (TEM) analysis confirmed existence of high crystalline CuO nanopetals with average length and diameter of 1611.96 nm and 650.50 nm, respectively. The nanopetals are monodispersed with a large surface area, controlled morphology, and demonstrate the nanocrystalline nature with a monoclinic structure. The phase purity of the as-synthesized sample was confirmed by Raman spectroscopy and X-ray diffraction (XRD) patterns. A significantly wide absorption up to 800 nm and increased band gap were observed in CuO nanopetals. The valance band (VB) and conduction band (CB) positions at CuO surface are measured to be of +0.7 and −1.03 eV, respectively, using X-ray photoelectron spectroscopy (XPS), which would be very promising for efficient catalytic properties. Furthermore, the obtained CuO nanopetals in the presence of hydrogen peroxide ( H 2 O 2 ) achieved excellent catalytic activities for degradation of methylene blue (MB) under dark, with degradation rate > 99% after 90 min, which is significantly higher than reported in the literature. The enhanced catalytic activity was referred to the controlled morphology of monodispersed CuO nanopetals, co-operative role of H 2 O 2 and energy band structure. This work contributes to a new approach for extensive application opportunities in environmental improvement.

scholarly journals Heterogeneous Fenton-like oxidation of p-hydroxybenzoic acid using Fe/CeO2-TiO2 catalyst

2019 ◽  
Vol 79 (7) ◽  
pp. 1276-1286 ◽  
Author(s):  
Tijani Hammedi ◽  
Mohamed Triki ◽  
Mayra G. Alvarez ◽  
Jordi Llorca ◽  
Abdelhamid Ghorbel ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Molar Ratio ◽  
Hydroxybenzoic Acid ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission ◽  
Temperature Programmed

Abstract This paper is built on the Fenton-like oxidation of p-hydroxybenzoic acid (p–HBZ) in the presence of H2O2 and 3%Fe supported on CeO2-TiO2 aerogels under mild conditions. These catalysts were deeply characterized by X-ray diffraction (XRD), hydrogen temperature programmed reduction (H2-TPR), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and X-ray photoelectron spectroscopy (XPS). The effect of thermal treatment, pH (2–3, 5, 7), H2O2/p–HBZ molar ratio (5, 15, 20, 25) and reaction temperature (25 °C, 40 °C and 60 °C) on the catalytic properties of supported Fe catalysts are studied. Our results highlight the role of CeO2 and the calcination of the catalyst to obtain the highest catalytic properties after 10 min: 73% of p–HBZ conversion and 52% of total organic carbon (TOC) abatement.

Synthesis of Au-SiO2 Composite Nanospheres and Their Catalytic Activity

2016 ◽  
Vol 16 (4) ◽  
pp. 3821-3826 ◽  
Author(s):  
Wang Dexuan ◽  
Li Guian ◽  
Han Qingyan ◽  
Wang Ziqiang ◽  
Pan Liping ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Photoelectron Spectroscopy ◽  
Au Nanoparticles ◽  
Catalytic Properties ◽  
Organic Dyes ◽  
Chemical Elements ◽  
X Ray ◽  
Transmission Electron ◽  
Environmentally Friendly Approach

We report a simple and environmentally friendly approach to the synthesis of Au-SiO2 composite nanospheres. Our method presents a route for the decoration of preformed amine functionalized SiO2 nanospheres by in situ formation of Au nanoparticles at three different concentrations of Au precursor (HAuCl4). Herein, the silane coupling agent (KH-550) is used as an intermediary to connect the Au nanoparticles to the surfaces of the SiO2 nanospheres, which helps avoid the aggregation of Au nanoparticles. The crystal structure, chemical elements, morphology and catalytic properties of the Au-SiO2 composite nanospheres were analyzed by transmission electron microscopy (TEM), X-Ray powder diffraction (XRD), UV-vis-spectrophotometer (UV-vis) and X-ray photoelectron spectroscopy (XPS). The analytical results demonstrate that the Au nanoparticles (4–9 nm) were homogeneously distributed on the surface of the SiO2 nanospheres, which had a good FCC crystal structure. Moreover, the Au-SiO2 composite nanospheres exhibited good catalytic properties, measured by their ability to reduce organic dyes. The Au-SiO2 composite nanospheres are promising candidates for applications in catalysis and wastewater treatment.

scholarly journals A Colorimetric Assay for the Detection of Glucose and H2O2 Based on Cu-Ag/g-C3N4/ZIF Hybrids with Superior Peroxidase Mimetic Activity

Molecules ◽  
2020 ◽  
Vol 25 (19) ◽  
pp. 4432
Author(s):  
Quan Pan ◽  
Yuelin Kong ◽  
Kuan Chen ◽  
Mi Mao ◽  
Xiaohui Wan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Catalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Colorimetric Assay ◽  
X Ray Diffraction ◽  
Zeolitic Imidazolate Framework ◽  
X Ray ◽  
Transmission Electron ◽  
H2o2 Generation

In this work, we report the synthesis of Cu-Ag bimetallic nanopartiles and g-C3N4 nanosheets decorated on zeolitic imidazolate framework-8 (ZIF-8) to form a Cu-Ag/g-C3N4/ZIF hybrid. The hybrid was synthesized and characterized by Transmission electron microscopy (TEM), Fourier transformed infrared (FTIR), the X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Cu-Ag/g-C3N4/ZIF hybrid has intrinsic peroxidaselike catalytic activity towards the oxidation of TMB in the presence of H2O2. The situ synthesis of Cu-Ag bimetallic nanopartiles on 2D support such as g-C3N4 nanosheets would significantly enhance the peroxidaselike catalytic properties of individual Cu-Ag bimetallic nanopartiles and the g-C3N4 nanosheets. After loading of Cu-Ag bimetallic nanopartiles and g-C3N4 nanosheets on the ZIF-8, the hybrids exhibited superior peroxidaselike catalytic activity and good recyclability. Then, this method was applied for detecting glucose in human serum, owing the significant potential for detection of metabolites with H2O2-generation reactions.

scholarly journals Preparation of a Series of Pd@UIO-66 by a Double-Solvent Method and Its Catalytic Performance for Toluene Oxidation

Materials ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 88 ◽  
Author(s):  
Chuanying Wei ◽  
Haili Hou ◽  
Ermo Wang ◽  
Min Lu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Active Sites ◽  
Catalytic Properties ◽  
Catalytic Performance ◽  
Adsorbed Oxygen ◽  
Large Specific Surface Area ◽  
Toluene Oxidation ◽  
X Ray ◽  
Solvent Method ◽  
Transmission Electron

This paper reports on the preparation, characterization, and catalytic properties of the Pd@UIO-66 for toluene oxidation. The samples are prepared by the double-solvent method to form catalysts with large specific surface area, highly dispersed Pd0 (Elemental palladium) and abundant adsorbed oxygen, which are characterized by X-ray Photoelectron Spectroscopy (XPS), Brunauer-Emmett-Teller (BET) and Transmission Electron Microscopy (TEM). The results show that as the Pd content increases, the adsorbed oxygen content further increases, but at the same time Pd0 will agglomerate and lose some active sites, which will affect its catalytic performance. While 0.2%Pd@UIO-66 has the highest concentration of Pd0, the result shows it has the best catalytic activity and the T90 temperature is 210 °C.

scholarly journals α-Cellulose Fibers of Paper-Waste Origin Surface-Modified with Fe3O4 and Thiolated-Chitosan for Efficacious Immobilization of Laccase

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 581
Author(s):  
Gajanan S. Ghodake ◽  
Surendra K. Shinde ◽  
Ganesh D. Saratale ◽  
Rijuta G. Saratale ◽  
Min Kim ◽  
...  
Keyword(s):  
Enzyme Immobilization ◽  
Photoelectron Spectroscopy ◽  
Cellulose Fibers ◽  
Relative Activity ◽  
Significant Activity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Laccase Immobilization ◽  
Surface Modified

The utilization of waste-paper-biomass for extraction of important α-cellulose biopolymer, and modification of extracted α-cellulose for application in enzyme immobilization can be extremely vital for green circular bio-economy. Thus, in this study, α-cellulose fibers were super-magnetized (Fe3O4), grafted with chitosan (CTNs), and thiol (-SH) modified for laccase immobilization. The developed material was characterized by high-resolution transmission electron microscopy (HR-TEM), HR-TEM energy dispersive X-ray spectroscopy (HR-TEM-EDS), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FT-IR) analyses. Laccase immobilized on α-Cellulose-Fe3O4-CTNs (α-Cellulose-Fe3O4-CTNs-Laccase) gave significant activity recovery (99.16%) and laccase loading potential (169.36 mg/g). The α-Cellulose-Fe3O4-CTNs-Laccase displayed excellent stabilities for temperature, pH, and storage time. The α-Cellulose-Fe3O4-CTNs-Laccase applied in repeated cycles shown remarkable consistency of activity retention for 10 cycles. After the 10th cycle, α-Cellulose-Fe3O4-CTNs possessed 80.65% relative activity. Furthermore, α-Cellulose-Fe3O4-CTNs-Laccase shown excellent degradation of pharmaceutical contaminant sulfamethoxazole (SMX). The SMX degradation by α-Cellulose-Fe3O4-CTNs-Laccase was found optimum at incubation time (20 h), pH (3), temperatures (30 °C), and shaking conditions (200 rpm). Finally, α-Cellulose-Fe3O4-CTNs-Laccase gave repeated degradation of SMX. Thus, this study presents a novel, waste-derived, highly capable, and super-magnetic nanocomposite for enzyme immobilization applications.

scholarly journals Novel Carbon Dots Derived from Glycyrrhizae Radix et Rhizoma and Their Anti-Gastric Ulcer Effect

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1512
Author(s):  
Yuhan Liu ◽  
Meiling Zhang ◽  
Jinjun Cheng ◽  
Yue Zhang ◽  
Hui Kong ◽  
...  
Keyword(s):  
Gastric Ulcer ◽  
Photoelectron Spectroscopy ◽  
Carbon Dots ◽  
High Performance ◽  
Raw264.7 Cells ◽  
Mice Model ◽  
X Ray ◽  
Glycyrrhizae Radix ◽  
Transmission Electron ◽  
High Resolution Tem

Glycyrrhizae Radix et Rhizoma (GRR) is one of the commonly used traditional Chinese medicines in clinical practice, which has been applied to treat digestive system diseases for hundreds of years. GRR is preferred for anti-gastric ulcer, however, the main active compounds are still unknown. In this study, GRR was used as precursor to synthesize carbon dots (CDs) by a environment-friendly one-step pyrolysis process. GRR-CDs were characterized by using transmission electron microscopy, high-resolution TEM, fourier transform infrared, ultraviolet-visible and fluorescence spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and high-performance liquid chromatography. In addition, cellular toxicity of GRR-CDs was studied by using CCK-8 in RAW264.7 cells, and the anti-gastric ulcer activity was evaluated and confirmed using mice model of acute alcoholic gastric ulcer. The experiment confirmed that GRR-CDs were the spherical structure with a large number of active groups on the surface and their particle size ranged from 2 to 10 nm. GRR-CDs had no toxicity to RAW264.7 cells at concentration of 19.5 to 5000 μg/mL and could reduce the oxidative damage of gastric mucosa and tissues caused by alcohol, as demonstrated by restoring expression of malondialdehyde, superoxide dismutase and nitric oxide in serum and tissue of mice. The results indicated the explicit anti-ulcer activity of GRR-CDs, which provided a new insights for the research on effective material basis of GRR.

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

2021 ◽  
pp. 174751982098472
Author(s):  
Jun Yu ◽  
Ying Han ◽  
Guoqing Chen ◽  
Xiuzhen Xiao ◽  
Haifang Mao ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Co Hydrogenation ◽  
X Ray ◽  
Highly Active ◽  
Transmission Electron ◽  
Co Insertion ◽  
Temperature Programmed Surface Reaction ◽  
Temperature Programmed ◽  
Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

scholarly journals Synthesis, characterization and in vitro cytotoxicity study of Co and Ni ferrite nanoparticles prepared by sol-gel method

2021 ◽  
Vol 3 (7) ◽  
Author(s):  
Alexandre Pancotti ◽  
Dener Pereira Santos ◽  
Dielly Oliveira Morais ◽  
Mauro Vinícius de Barros Souza ◽  
Débora R. Lima ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Test Sample ◽  
In Vitro Cytotoxicity ◽  
Gel Method ◽  
X Ray ◽  
Sol Gel Method ◽  
Transmission Electron ◽  
Crystallite Sizes

AbstractIn this study, we report the synthesis and characterization of NiFe2O4 and CoFe2O4 nanoparticles (NPs) which are widely used in the biomedical area. There is still limited knowledge how the properties of these materials are influenced by different chemical routes. In this work, we investigated the effect of heat treatment over cytotoxicity of cobalt and niquel ferrites NPs synthesized by sol-gel method. Then the samples were studied using transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), Fourier Transform Infrared Spectroscopy Analysis (FTIR), and X-ray fluorescence (XRF). The average crystallite sizes of the particles were found to be in the range of 20–35 nm. The hemocompatibility (erythrocytes and leukocytes) was checked. Cytotoxicity results were similar to those of the control test sample, therefore suggesting hemocompatibility of the tested materials.

scholarly journals Surface Stoichiometry and Depth Profile of Tix-CuyNz Thin Films Deposited by Magnetron Sputtering

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3191
Author(s):  
Arun Kumar Mukhopadhyay ◽  
Avishek Roy ◽  
Gourab Bhattacharjee ◽  
Sadhan Chandra Das ◽  
Abhijit Majumdar ◽  
...  
Keyword(s):  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Film Surface ◽  
Grazing Incidence ◽  
X Ray Diffraction ◽  
X Ray ◽  
Relative Composition ◽  
Transmission Electron ◽  
Deposited Film ◽  
Deposited Films

We report the surface stoichiometry of Tix-CuyNz thin film as a function of film depth. Films are deposited by high power impulse (HiPIMS) and DC magnetron sputtering (DCMS). The composition of Ti, Cu, and N in the deposited film is investigated by X-ray photoelectron spectroscopy (XPS). At a larger depth, the relative composition of Cu and Ti in the film is increased compared to the surface. The amount of adventitious carbon which is present on the film surface strongly decreases with film depth. Deposited films also contain a significant amount of oxygen whose origin is not fully clear. Grazing incidence X-ray diffraction (GIXD) shows a Cu3N phase on the surface, while transmission electron microscopy (TEM) indicates a polycrystalline structure and the presence of a Ti3CuN phase.

Sign in / Sign up

Export Citation Format

Share Document